Sony MP595 Ground the power harness, Power connections, Correct wire splicing, Crimp terminals

Page 34

AirLink MP595 / MP595W Modem User Guide

Note: If you choose to install a separate switch, it must be connected to the white ignition sense wire, not the red battery wire, so that the MP modem can perform a controlled shutdown, as described on page 27.

Note: Ensure that all wires are correctly spliced or crimped. Improper grounding and wire connections may lead to equipment damage or safety hazards.

on when the ignition is switched to “Accessory” mode. In this configuration, the MP modem is on whenever other vehicle electrical devices can be switched on—such as when the radio and windshield fan can run.

—or—

Separately switched. Connect the white ignition sense wire to a separate switch mounted in a convenient location, which allows the MP modem to be turned on or off regardless of the position of the ignition key. In this configuration, the MP modem can be powered on or off even if the key is not in the ignition.

The MP modem also has a “Power Off Timer”. When power is removed from the ignition sense wire, the MP modem remains on for the period defined by the Power Off Timer, up to a maximum of 240 minutes. The Power Off Timer is configured in 3G Watcher. See the online help in 3G Watcher for details.

Ground the power harness

You must connect the black ground wire from the power harness to the grounded negative terminal of the vehicle battery, or another appropriate electrical ground. Failing to ground the power harness properly may damage the MP modem, may cause radio interference, and can be dangerous. (See “Ground the MP modem” on page 22.) The ground wire in the MP modem power harness is not fused.

Power connections

Connecting the MP modem’s power wires properly is important—poor connections can damage the wiring, the MP modem, or the vehicle’s electrical system, and can be dangerous.

Correct wire splicing

You can splice the wires of the power harness to the car wiring. Proper splicing is essential to reliable operation of the MP modem. Do NOT use “quick taps”; they reduce the integrity of the wire that is cut and let moisture into the cable.

An appropriate method of splicing is to strip a small portion of the insulation, solder the wires together, then heat‐shrink the connection to re‐insulate it.

Crimp terminals

If suitable terminal connection points are available on the vehicle for power and ignition sense, then using automotive crimp terminals is recommended. When using crimp

 

 

 

 

 

 

 

28

 

 

 

 

 

2130795

 

 

 

Image 34
Contents User Guide for Verizon Page Important Notice Safety and Hazards Limitation Liability Patents Copyright Qualcomm 3GSupport@sierrawireless.com Trademarks Contact InformationDirecting users to the MP 3G Modems AT Command Reference Revision HistoryContents MP Modem Operation Configuring the Router Functions Support and Warranty Regulatory Information AirLink MP595 / MP595W Modem User Guide 2130795 Introducing the MP Modem About Cdma Cdma account and coverageConnection methods Receive diversitySupported Cdma radio frequencies Virtual serial port VPN support for RnapDocumentation SoftwareMP Modem Manager AirLink MP595 / MP595W Modem User Guide Getting Started Where do you want to install your MP modem? Plan your MP modem installationWhat type of connections do you plan to use? Getting Started Required equipment Package contentsAdditional required equipment MP modem accessories System requirementsAirLink MP595 / MP595W Modem User Guide 2130795 Installation overview Hardware and Software InstallationMP modem housing Overview of installation steps Connector panelGPS and I/O options Select a location for the MP modem Install the MP modemMount the MP modem Mounting the MP modemGround the MP modem Mounting the MP modem. Arrows indicate the mounting holesMount the antennas and install the cables Main RF antennaMP 595880W only GPS antennaAntenna locations Install the antennas and cables Power connector Molex pinouts Install the power harnessPower connector Vehicle installationIgnition sense on/off wiring Ignition sense optionsCorrect wire splicing Ground the power harnessPower connections Crimp terminalsOffice installation Connect the MP modem to computer cableSerial connector DB9 pinouts Install the USB, Ethernet or serial cableActivate your account Install the softwarePort connections Manual activation Test the systemActivation Wizard Automated activationMP Modem Operation Turning the MP modem on and offStatus indicators LED operation3G Watcher software Reset the MP modem3G Watcher Help Connection to MP Physical Interface Launching 3G WatcherChanging the Physical Interface Establishing connections 3G Watcher windowAuto-Connect for DUN You now have DUN connectionConfiguring the Router Functions NAT modeNon-NAT mode NAT modeMP modem networking basics in NAT ModeSet up static IP addresses Static IP and TCP/UDP port forwarding in NAT modeEnable the router File and resource sharing over LANSet up TCP/UDP port forwarding AirLink MP595 / MP595W Modem User Guide 2130795 Configuring the Wireless Access Point OverviewUnlock MP modem configuration Change the password optionalEnable the wireless access point Set the SsidConfigure the security settings Reset the MP modem to factory defaults Configure security on the client computersAirLink MP595 / MP595W Modem User Guide 2130795 Configuring the MP Modem to Report GPS and I/O Data GPS configuration and reportingGPS protocols and commands GPS display in 3G WatcherDevice installation and configuration GPS Taip quick referencePort specifications Connector pinoutsDigital input devices A button wired to Pin 4 digital input and Pin 10 Ground Example panic button connectionsDigital output devices Analog input devicesConfiguration using AT or 3G Watcher commands Example analog sensor connectionsAnalog input setup ExampleDigital I/O setup AirLink MP595 / MP595W Modem User Guide 2130795 Sending Data to Your Network Application Configure the MP modem toReport frequency timers Route data to a serverTmsumregind Sending Data to Your Network Application Monitoring and Tracking configuration IP AddressingProblem created by Network Address Translation Solutions to the NAT problem Retrieve the Unique Mobile Device IDWarranty Support and WarrantyTechnical support AirLink MP595 / MP595W Modem User Guide 2130795 Technical Specifications Regulatory, radio frequency and electrical specificationsEnvironmental specifications Weight and dimensionsHost interfaces GPS specificationsOther interfaces Port characteristics Wireless access point specificationsWPA2 AirLink MP595 / MP595W Modem User Guide 2130795 Regulatory Information CanadaFCC Caution Important NoteApproved antennas Index NumericsRev 1.5 Jul.08 Index Wireless Access Point. See WAP Document SubTitle 2130795

MP595 specifications

The Sony MP595 is a sophisticated multimedia projector that offers advanced features ideal for both professional and personal use. Renowned for its superb image quality and versatile functionality, the MP595 is designed to deliver exceptional visual experiences in a variety of settings.

One of the standout characteristics of the MP595 is its high resolution. It typically supports resolutions up to 1920x1080, allowing for sharp and detailed images that enhance presentations and media consumption. This capability is particularly advantageous for businesses and educational institutions that require clarity for their visual content, from presentations to detailed graphs and charts.

The projector employs advanced DLP (Digital Light Processing) technology, which contributes to its vibrant color reproduction and excellent contrast ratios. This technology minimizes the presence of rainbow artifacts, providing a more seamless viewing experience. The result is bright, rich colors that captivate audiences, making it a perfect choice for movie nights, corporate presentations, or classroom settings.

Another notable feature is the MP595's portability. Weighing modestly, it features a compact design that makes it easy to transport to various locations. Whether it’s moving from a conference room to a training seminar, the lightweight nature of the projector simplifies setup and takedown, ensuring that users can focus more on their presentations rather than logistics.

Connectivity options are plentiful with the MP595, allowing users to easily connect to various devices. It usually includes HDMI, VGA, and USB ports, accommodating laptops, tablets, and other media players. Wireless connectivity capabilities further expand its versatility, enabling presentations directly from smartphones or tablets without the need for cables.

In terms of sound, the Sony MP595 integrates a robust built-in audio system that enhances the overall experience. This eliminates the need for external speakers in smaller settings, making it an all-in-one solution for presentations and home entertainment.

Additionally, the projector often features adjustable settings for lens shift and keystone correction, which help in achieving optimal image alignment on any surface. These adjustments are crucial for maintaining image integrity when projecting from various angles.

Overall, the Sony MP595 stands out with its high-resolution capabilities, portability, versatile connectivity, and advanced technologies. It is a reliable choice for anyone looking to enhance their visual presentations, whether for business, education, or entertainment purposes. The combination of these features positions the MP595 as a formidable player in the multimedia projector market.