Sony MP595 manual Mount the antennas and install the cables, Main RF antenna

Page 29

Note: Tighten cables connected to the MP modem by hand. Do not use tools.

Hardware and Software Installation

You can also use a ground screw on the connector panel of the MP modem. Use a 16‐gauge wire if you choose to use a ground screw. A ground screw is not required as long as the power harness is properly grounded.

I/O

Power

If you are using a ground screw, insert it here.

Figure 3-4: The ground screw connector on the connector panel.

Step 2—Mount the antennas and install the cables

The MP 595 modem has two Main RF antenna connectors and one GPS antenna connector. The MP 595W has an additional RF antenna connector for an AP antenna. The MP modem requires an RF antenna to connect to the wireless network. The second RF connector is optional and allows for receive diversity.

The built‐in GPS module requires a dedicated GPS antenna or a combination antenna with cables to both the Main RF and GPS antenna connectors on the MP modem.

If you already have an MP modem combination GPS antenna, you can re‐use it with your new MP modem. This antenna has two leads—one for Main RF (TNC connector) and one for GPS (SMA connector).

Main RF antenna

Use an approved Main RF antenna to connect to the wireless network. The antenna must have 50 ohms impedance and a cable with a TNC connector (or SMA connector if the antenna is being used for receive diversity), as well as the following characteristics:

The total maximum gain, including cable loss, must not exceed 4.15 dBi (if the antenna operates on the PCS band) or 5.1 dBi (if the antenna operates only on the Cellular band).

The antenna must transmit and receive on the necessary frequency bands in your coverage area. The MP modem supports these RF bands:

 

 

 

 

 

 

 

Rev 1.5 Jul.08

 

 

 

 

 

23

 

 

 

Image 29
Contents User Guide for Verizon Page Important Notice Safety and Hazards Limitation Liability Qualcomm 3G Patents CopyrightTrademarks Contact Information Support@sierrawireless.comRevision History Directing users to the MP 3G Modems AT Command ReferenceContents MP Modem Operation Configuring the Router Functions Support and Warranty Regulatory Information AirLink MP595 / MP595W Modem User Guide 2130795 Introducing the MP Modem Cdma account and coverage About CdmaSupported Cdma radio frequencies Receive diversityConnection methods VPN support for Rnap Virtual serial portMP Modem Manager SoftwareDocumentation AirLink MP595 / MP595W Modem User Guide Getting Started What type of connections do you plan to use? Plan your MP modem installationWhere do you want to install your MP modem? Getting Started Additional required equipment Package contentsRequired equipment System requirements MP modem accessoriesAirLink MP595 / MP595W Modem User Guide 2130795 MP modem housing Hardware and Software InstallationInstallation overview GPS and I/O options Connector panelOverview of installation steps Mount the MP modem Install the MP modemSelect a location for the MP modem Mounting the MP modemMounting the MP modem. Arrows indicate the mounting holes Ground the MP modemMain RF antenna Mount the antennas and install the cablesAntenna locations GPS antennaMP 595880W only Install the antennas and cables Power connector Install the power harnessPower connector Molex pinouts Vehicle installationIgnition sense options Ignition sense on/off wiringPower connections Ground the power harnessCorrect wire splicing Crimp terminalsConnect the MP modem to computer cable Office installationInstall the USB, Ethernet or serial cable Serial connector DB9 pinoutsPort connections Install the softwareActivate your account Activation Wizard Test the systemManual activation Automated activationTurning the MP modem on and off MP Modem OperationLED operation Status indicators3G Watcher Help Reset the MP modem3G Watcher software Changing the Physical Interface Launching 3G WatcherConnection to MP Physical Interface 3G Watcher window Establishing connectionsYou now have DUN connection Auto-Connect for DUNNAT mode Configuring the Router FunctionsNAT mode Non-NAT modeMode MP modem networking basics in NATEnable the router Static IP and TCP/UDP port forwarding in NAT modeSet up static IP addresses File and resource sharing over LANSet up TCP/UDP port forwarding AirLink MP595 / MP595W Modem User Guide 2130795 Overview Configuring the Wireless Access PointChange the password optional Unlock MP modem configurationSet the Ssid Enable the wireless access pointConfigure the security settings Configure security on the client computers Reset the MP modem to factory defaultsAirLink MP595 / MP595W Modem User Guide 2130795 GPS configuration and reporting Configuring the MP Modem to Report GPS and I/O DataGPS display in 3G Watcher GPS protocols and commandsGPS Taip quick reference Device installation and configurationDigital input devices Connector pinoutsPort specifications Example panic button connections A button wired to Pin 4 digital input and Pin 10 GroundAnalog input devices Digital output devicesExample analog sensor connections Configuration using AT or 3G Watcher commandsExample Analog input setupDigital I/O setup AirLink MP595 / MP595W Modem User Guide 2130795 Report frequency timers Configure the MP modem toSending Data to Your Network Application Route data to a serverTmsumregind Sending Data to Your Network Application IP Addressing Monitoring and Tracking configurationProblem created by Network Address Translation Retrieve the Unique Mobile Device ID Solutions to the NAT problemTechnical support Support and WarrantyWarranty AirLink MP595 / MP595W Modem User Guide 2130795 Regulatory, radio frequency and electrical specifications Technical SpecificationsWeight and dimensions Environmental specificationsOther interfaces GPS specificationsHost interfaces Wireless access point specifications Port characteristicsWPA2 AirLink MP595 / MP595W Modem User Guide 2130795 Canada Regulatory InformationApproved antennas Important NoteFCC Caution Numerics IndexRev 1.5 Jul.08 Index Wireless Access Point. See WAP Document SubTitle 2130795

MP595 specifications

The Sony MP595 is a sophisticated multimedia projector that offers advanced features ideal for both professional and personal use. Renowned for its superb image quality and versatile functionality, the MP595 is designed to deliver exceptional visual experiences in a variety of settings.

One of the standout characteristics of the MP595 is its high resolution. It typically supports resolutions up to 1920x1080, allowing for sharp and detailed images that enhance presentations and media consumption. This capability is particularly advantageous for businesses and educational institutions that require clarity for their visual content, from presentations to detailed graphs and charts.

The projector employs advanced DLP (Digital Light Processing) technology, which contributes to its vibrant color reproduction and excellent contrast ratios. This technology minimizes the presence of rainbow artifacts, providing a more seamless viewing experience. The result is bright, rich colors that captivate audiences, making it a perfect choice for movie nights, corporate presentations, or classroom settings.

Another notable feature is the MP595's portability. Weighing modestly, it features a compact design that makes it easy to transport to various locations. Whether it’s moving from a conference room to a training seminar, the lightweight nature of the projector simplifies setup and takedown, ensuring that users can focus more on their presentations rather than logistics.

Connectivity options are plentiful with the MP595, allowing users to easily connect to various devices. It usually includes HDMI, VGA, and USB ports, accommodating laptops, tablets, and other media players. Wireless connectivity capabilities further expand its versatility, enabling presentations directly from smartphones or tablets without the need for cables.

In terms of sound, the Sony MP595 integrates a robust built-in audio system that enhances the overall experience. This eliminates the need for external speakers in smaller settings, making it an all-in-one solution for presentations and home entertainment.

Additionally, the projector often features adjustable settings for lens shift and keystone correction, which help in achieving optimal image alignment on any surface. These adjustments are crucial for maintaining image integrity when projecting from various angles.

Overall, the Sony MP595 stands out with its high-resolution capabilities, portability, versatile connectivity, and advanced technologies. It is a reliable choice for anyone looking to enhance their visual presentations, whether for business, education, or entertainment purposes. The combination of these features positions the MP595 as a formidable player in the multimedia projector market.