Sony KP-43T75A, KP-53SV75A service manual Registration Adjustment PJE, Setup for Adjustment

3-10. REGISTRATION ADJUSTMENT (PJE)

•FUNCTION OF BUTTONS OF REMOTE COMMANDER FOR PJE MODE.

		MUTING		DVD/	SAT/	POWER
				VTR	CABLE
						TV
		SYSTEM		FUNCTION			Color select
		OFF	DVD/VTR SAT/CABLE			TV
Adjustment item
		TV/VTR	FREEZE		SWAP	PIP	GRNnBLUnRED
up				m	N	M
		X		z	x	ACTIVE
			POSITION		AUDIO		Test signal select
			SLEEP		ANT	TV/VIDEO
		PICTURE		CC MTS/SAP		DISPLAY	crosshach+video signal
		MODE
Adjustment item
		1		2	3		dots+video signal
down		4		5	6		crosshach+black
		7		8	9		dots+black
		JUMP			ENTER		off
				0
INIT*		INDEX				GUIDE
							Mode select
		RESET				MENU
			VOL		CH		(FineCoarseadjustmentadjustment)
READ*		CODE SET
							ENTER
				TV
data up/down
INIT*:	Press 7, "INIT" green letters appear on the screen.
	Then press ENTER, all the PJE data are reset.
READ*:	Press 0, "READ" green letters appear on the screen.
	Then press ENTER, all the PJE default data are
	restored.

Note: Internal patterns are used for geometry and convergence adjustments. However, sizing and centering must be done with the use of an external generator. The recommended pattern would be a monoscope, or equivalent pattern, which would provide the means to adjust both the linearity and sizing of the picture.

[SETUP FOR ADJUSTMENT]

•Current flow in circuit should be stable before attempting adjustment. So wait 5 minutes after turning on the TV power.

•At the 4 insides of the screen, locate the middle. Use a tape measure to identify the middle.

: middle

•Separate adjustments are required for multiple modes and should be done in the following order (as each mode requires a separate adjustment) :

•NTSC mode

•PAL-N mode

In all these modes, both color convergence and geometry adjustment affects each other.

KP-43T75A/53SV75A

RM-Y906 RM-Y906

1.Set to the service mode by pressing quickly keys on the remote commander in the standby mode in the following order:

[DISPLAY] n5 n[VOL+] n[TV POWER]

2.Change TV mode to the video input mode.

3.Change the VPNT mode to the PJE 00 FDIS.

PJE 00 00

FDIS

4.Set FDIS data to “01” to display the registration data of each spot in the fine adjustment.

PJE 00 01

FDIS

5.Press 6 to display the test signal (crosshatch) on the screen.

6.Select GRN CENT(*) with the 1 and 4 keys on the remote commander and check that the adjustment data is now “000” both vertically and horizontally.

	(H)	(V)
GRN	000	000
CENT

*: In the factory preset, “GRN CENT” appears on the screen first. In case of other colors “RED” or “BLU”, change color by every pressing 3 key.

7.Cover the both red and blue picture lenses with the lens caps to show only the green color.

SUB DEFLECTION ADJUSTMENT ITEM
Adjustment	O : Yes	– : No
				Adjustment type
Display	Adjustment item		G		R	B
			H/V		H/V	H/V
CENT	CENT		O/O		O/O	O/O
SKEW	SKEW		O/O		O/O	O/O
SIZE	SIZE		–/–		O/O	O/O
LIN	LIN		–/–		O/–	O/–
KEY	KEY		–/–		–/O	–/O
PIN	PIN		–/O		–/O	–/O

– 35 –