Dell E19S, R520 Installing An AC Power Supply, Wiring Instructions For a DC Power Supply

Page 78

Installing An AC Power Supply

CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.

1.Verify that both the power supplies are the same type and have the same maximum output power.

NOTE: The maximum output power (shown in Watts) is listed on the power supply label.

2.If applicable, remove the power supply blank.

3.Slide the new power supply into the chassis until the power supply is fully seated and the release latch snaps into place.

NOTE: If you unlatched the cable management arm, re-latch it. For information about the cable management arm, see the system’s rack documentation.

4.Connect the power cable to the power supply and plug the cable into a power outlet.

CAUTION: When connecting the power cable, secure the cable with the strap.

NOTE: When installing, hot-swapping, or hot-adding a new power supply, allow several seconds for the system to recognize the power supply and determine its status. The power-supply status indicator turns green to signify that the power supply is functioning properly.

Wiring Instructions For A DC Power Supply

Your system supports up to two –(48–60) V DC power supplies (when available).

WARNING: For equipment using –(48–60) V DC power supplies, a qualified electrician must perform all connections to DC power and to safety grounds. Do not attempt connecting to DC power or installing grounds yourself. All electrical wiring must comply with applicable local or national codes and practices. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow all safety instructions that came with the product.

CAUTION: Wire the unit with copper only, unless otherwise specified, use only 10 American Wire Gauge (AWG) wire rated minimum 90 ºC for source and return. Protect the –(48–60) V DC (1 wire) with a branch circuit over- current protection rated 50 A for DC with a high interrupt current rating.

NOTE: A readily accessible disconnect device that is suitably approved and rated shall be incorporated in the field wiring.

Input Requirements

Supply voltage: –(48–60) V DC

Current consumption: 32 A (maximum)

Kit Contents

Dell part number 6RYJ9 terminal block or equivalent (1)

#6-32 nut equipped with lock washer (1)

Required Tools

Wire-stripper pliers capable of removing insulation from size 10 AWG solid or stranded, insulated copper wire

78

Image 78
Contents Regulatory Model E19S Series Regulatory Type E19S001 Dell Inc. All Rights Reserved Contents Installing Memory Modules Installing System ComponentsMemory Optimized Independent Channel Mode Installing a Dual Slot Hard-Drive BlankInstalling The Power Supply Blank Installing The Optical DriveExpansion-Card Installation Guidelines Internal USB Memory Key OptionalWhen To Use The Embedded System Diagnostics 101111 123 113117 141Page Front-Panel Features And Indicators Indicator, Button, or Icon Description ConnectorUse this button only if directed to do so by qualified Front and the system status indicator on the backUSB connectors Support personnel or by the operating systemsLCD Panel Features Home ScreenButton Description Setup Menu View MenuOff Hard-Drive Indicator PatternsDrive-Status Condition Indicator Pattern RAID Only SecondsConnects a PCI Express expansion card Back-Panel Features And IndicatorsConnector Through the optional cable management arm CompliantNIC Indicator Codes Power Indicator CodesPower supply and that the power supply is operational AC power supply status indicator/handleDC power supply status indicator Flashing amber Indicates a problem with the power supplyPower Indicator Codes For Non-Redundant Power Supply Diagnostic Indicator Condition Pattern Green Other Information You May NeedF10 Choosing The System Boot ModeKeystroke Description F11 F12Entering System Setup Responding To Error MessagesUsing The System Setup Navigation Keys System Bios Screen System Setup OptionsSystem Setup Main Screen System Information ScreenMemory Settings Screen Processor Settings ScreenExecute Disable Option is set to EnabledPrefetcher option is set to Enabled Execute Disable option is set to EnabledSata Settings Screen Boot Settings ScreenIntegrated Devices Screen Serial Communications Screen System Profile Settings Screen System Security Screen System And Setup Password Features Miscellaneous SettingsAssigning a System And/Or Setup Password Operating With a Setup Password Enabled Entering The Uefi Boot ManagerUsing Your System Password To Secure Your System Boot Manager enables you toUsing The Boot Manager Navigation Keys Boot Manager ScreenEntering The iDRAC Settings Utility IDRAC Settings UtilityUefi Boot Menu Changing The Thermal SettingsPage Page Front Bezel Optional Installing The Front BezelRecommended Tools Release latchOpening The System Opening And Closing The SystemRemoving The Front Bezel Keylock Front bezel Locking hookInside The System Closing The SystemSystem cover Latch Latch release lock Cooling shroud Cooling fans Expansion-card latch Heat sink for processorDIMMs Inside the System-Non-Redundant Power Supply Unit Chassis Cooling ShroudRemoving and Installing the Cooling Shroud Removing The Cooling Shroud1333, 1066, Dual rank Installing The Cooling ShroudSystem Memory 1333, 1066 Dual rank Quad rankMemory channels are organized as follows ProcessorGeneral Memory Module Guidelines Mode-Specific GuidelinesAdvanced ECC Lockstep Memory Sparing Memory Optimized Independent Channel ModeSample Memory Configurations Memory Mirroring2R x4, 1600 MT/s 2R x4, 1333 MT/s 2R x4, 1600 MT/s B4, B5 192 2R x4, 1333 MT/s2R x4, 1600 MT/s B3, B4, B5, B6 Removing Memory Modules 256 4R x4, 1066 MT/s384 4R x4, 1066 MT/s Installing Memory Modules Removing The Memory ModuleInstalling The Memory Module Hard DrivesInstalling a 3.5 Inch Hard-Drive Blank Removing a 3.5 Inch Hard-Drive BlankHard-drive blank Release button Hard-Drive Blank Installation Sequence Removing a Dual Slot Hard-Drive BlankInstalling a Dual Slot Hard-Drive Blank Removing a Hot-Swap Hard DriveDual slot hard-drive blank Release tabs Installing a Hot-Swap Hard Drive Release button Hard drive Hard-drive carrier handleScrews Inch hard-drive adapter Inch hard drive Hard-drive carrier Screws Hard drive Screw holes Hard-drive carrier Screws Hard-drive adapter Inch hard drive Optical drive Power and data cable Release tab Optical Drive OptionalRemoving The Optical Drive Installing The Optical Drive Cooling FansRemoving a Cooling Fan Installing a Cooling Fan Removing and Installing a Cooling FanInternal USB Memory Key Optional Replacing the Internal USB KeyExpansion Card Slots Expansion-Card Installation GuidelinesExpansion Cards And Expansion-Card Risers RiserExternal RAID CNAs Gb NICs Removing An Expansion CardCard Priority Card Type Gb NICs Non-RAIDExpansion card Expansion-card latch Riser Installing An Expansion Card Riser Expansion-card latch Expansion cardExpansion-card riser Release tabs Riser guide pins Connector Removing Expansion-Card RisersInstalling Expansion-Card Risers Expansion-card riser Connector Riser guide pinsIDRAC Ports Card Optional Removing The iDRAC Ports Card Installing The iDRAC Ports Card Removing and Installing the iDRAC Ports CardSD vFlash Card Internal Dual SD ModuleReplacing An SD vFlash Card Removing The Internal Dual SD Module Blue pull tab Dual SD module SD cardInternal SD Card Installing The Internal Dual SD ModuleInstalling An Internal SD Card Removing An Internal SD CardIntegrated Storage Controller Card Removing The Integrated Storage ControllerInstalling The Integrated Storage Controller Storage connector on the system boardTouch-points Release levers Storage-controller card Processors Removing a ProcessorRemoving and Installing the Heat Sink Installing a Processor Processor ZIF socket Processor shieldNotches in processor Socket keys Power Supplies Removing An AC Power Supply Connector Power supply Release latch Power supply handleInstalling An AC Power Supply Wiring Instructions For a DC Power SupplySupply voltage -48-60 V DC Current consumption 32 a maximum Safety ground wire Grounding post #6-32 nut Locking washerDC power socket Wire -48 Rubber cap Wire RTN Captive screws DC power connectorConnector Release latch Power supply Removing a DC Power SupplyInstalling a DC Power Supply Power supply status indicatorRemoving The Power Supply Blank Installing The Power Supply BlankPower supply blank Removing The Power-Distribution And Power-Interposer Boards Power-distribution boardPower-interposer board Release tab Power-Distribution Board ConnectorsPower-Interposer Board Connectors Removing a Non-Redundant Power Supply Removing and Installing a Non-Redundant Power Supply Standoff on the chassisInstalling a Non-Redundant Power Supply Removing The Redundant Power Supply Unit DividerInstalling The Redundant Power Supply Unit Divider Redundant power supply unit dividerSystem Battery Replacing The System BatterySystem battery Battery connector Locate the battery socket Hard-Drive Backplane Removing The Hard-Drive BackplaneBackplane signal connector Securing hooksSystem board Installing The Hard-Drive Backplane Signal cable connector SAS a cable connectorControl Panel Assembly Removing The Control-Panel BoardControl-panel board Screws Control-panel data cable Installing The Control-Panel Board Removing The Control PanelUSB cable Installing The Control Panel System BoardNotches on chassis front wall Control panel Removing The System Board Installing The System Board Unpack the new system board assemblyRelease screws System board holder Page Troubleshooting External Connections Troubleshooting The Video SubsystemTroubleshooting a USB Device Troubleshooting a Serial I/O Device Troubleshooting a NICTroubleshooting a Wet System Troubleshooting a Damaged SystemTroubleshooting The System Battery Troubleshooting Power SuppliesTroubleshooting Cooling Problems Troubleshooting Cooling FansTroubleshooting System Memory Reseat the memory modules in their sockets Close the system Troubleshooting An Internal USB KeyTroubleshooting An SD Card 106Troubleshooting An Optical Drive Troubleshooting a Hard Drive Troubleshooting a Storage ControllerTroubleshooting Expansion Cards Troubleshooting Processors Dell Online Diagnostics Dell Embedded System Diagnostics When To Use The Embedded System DiagnosticsRunning The Embedded System Diagnostics System Diagnostic Controls Least one event description is recorded112 System Board Jumper Settings Jumper Setting DescriptionSystem Board Connectors Connector DescriptionDisabling a Forgotten Password Page Expansion Bus MemoryFront Connectors BackDrives InternalEnvironmental Temperature Temperature Continuous OperationMaximum Vibration EnvironmentalRelative Humidity Maximum ShockGaseous Contamination 122 Viewing LCD Messages System Error MessagesLCD Messages Removing LCD MessagesDetails Error CodeAMP0302 Message ActionBAT0017 Message ASR0003 MessageBAT0002 Message CPU0000 MessageCPU0204 Message CPU0010 MessageCPU0023 Message CPU0700 MessageCPU0702 Message CPU0703 MessageCPU0704 Message FAN0000 Message If the issue persists, see Getting HelpAction Reinstall or reconnect the hardware HWC2003 Message Details Fan operating speed is out of range ActionMEM0007 Message MEM0000 MessageMEM0001 Message MEM0701 MessagePCI1302 Message MEM1208 MessageMEM8000 Message PCI1304 MessagePCI1348 Message PCI1320 MessagePCI1342 Message PCI1360 MessagePSU0001 Message PST0128 MessagePST0129 Message PSU0002 MessagePSU0031 Message PSU0006 MessagePSU0016 Message PSU0032 MessagePSU0036 Message PSU0034 MessagePSU0035 Message PSU0037 MessageConfiguration and power consumption PSU1201 Message Power supply redundancy is lost DetailsSystem power inventory change System power consumptionRFM2001 Message RFM1014 MessageRFM1201 Message RFM2002 MessagePower. If problem persists call support SEL0006 Message All event logging is disabled DetailsAppear if the user disabled event logging Security may be compromisedFailures Issues persists, contact supportFailed TMP0121 MessageReinstall system cables Diagnostic MessagesReview system logs for power supply exceptions Alert Messages140 Getting Help Contacting Dell
Related manuals
Manual 8 pages 9.6 Kb