Dell MD3200i, MD3220i manual Post Installation Tasks

Page 43

If you have not selected Specify Configuration Manually for any of the two protocols, then you can skip step 8.

8If you have selected Specify Configuration Manually for any of the two protocols in the last step, a series of screens showing the backend view image of the storage array controllers is displayed. Each image contains IP addresses of management ports of the controllers. Also each image has one management port highlighted in red.

For IPv4 address of the highlighted port, enter the IP address, subnet mask and gateway address in the fields shown below the image in order to modify it.

For IPv6 address of the highlighted port, enter the local IP address, routable IP, and router IP address in the fields shown below the image in order to modify it.

Click Next to continue through these images to complete the configuration of all the management ports for the selected protocols.

9In the CHAP Configuration screen, select the CHAP method and click Next. For more information on CHAP see "Understanding CHAP Authentication" on page 63.

10In the Summary screen, review the information that you entered for the storage array.

Click Apply to save the changes to the storage array.

NOTE: To abort the configuration for the storage array and to go back to select a storage array for configuration, click Cancel Array.

11On the Configure Additional Arrays screen, select whether you want to configure additional array. Click Next to continue.

12If you selected Yes in the above step, then start again from step 4.

13If you selected No in step 12, then on the Configure Host Connectivity screen, select whether you want to configure the connectivity for current host’s iSCSI initiator. Click Next to continue.

If you selected No above, then you are done with the configuration task.

14Click Finish on the final screen to exit the utility.

Post Installation Tasks

43

Image 43
Contents Deployment Guide 2011 Rev. A01 Contents Uninstalling Dell PowerVault MD Storage ISCSI Configuration WorksheetDisk Configuration Utility Microsoft Windows Host SetupConfigure Chap Authentication on Uninstalling PowerVault MD Storage SoftwareConfigure the iSCSI Ports on Configure Host AccessConnect to the Target Storage Array From Appendix-Load BalancingSystem Requirements IntroductionManagement Station Requirements Introduction to Storage Arrays Introduction Introduction Planning the Storage Configuration Hardware InstallationRedundant and Non-Redundant Configurations Connecting the Storage ArrayCabling the Storage Array Single Path Data Configurations Direct-Attached ConfigurationsFour Hosts Connected to a Single Controller Shows two hosts connected to a single controller array Eight Hosts in a Dual-Controller Configuration Dual-Path Data Configuration Four Hosts Connected to Two Controllers Four Hosts Connected in a Dual-Controller Configuration Network-Attached Configurations Servers Connected to a Single Controller Servers Connected to Two Controllers Cabling PowerVault MD1200 Series Expansion Enclosures Hardware Installation Click Tools→ Upgrade RAID Controller Module Firmware Click Advanced→ Maintenance→ Download→ EMM Firmware Installing PowerVault MD Storage Software Graphical Installation Recommended Select Install MD Storage Software Silent Installation Console InstallationUpgrading PowerVault MD Storage Software Installing PowerVault MD Storage Software Standard Terminology Used in iSCSI Configuration Definition Post Installation TasksBefore You Begin ISCSI Configuration Worksheet Chap Secret IPv4 SettingsMutual Chap Target Chap IPv6 SettingsFE80 0000 0000 Host Server Vs. Storage Array Configuring iSCSI on Your Storage ArrayManager Storage Array Configuration Host Configuration Host Connectivity Configuration Configure the Storage Array Using PowerVault Mdcu Post Installation Tasks Post Installation Tasks Post Installation Tasks Configure the Host Connectivity Using PowerVault Mdcu Source Port Selection for iSCSI Host Ports Automatic Selection Post Connection Establishment Steps Microsoft Windows Host Setup Guidelines for Configuring Your Network for iSCSIControl Panel, select Network connections Edit the /etc/sysconfig/network file Linux Host SetupHWADDR=XXXXXXXXXXXX GATEWAY=192.168.1.1 Click Change/Remove Uninstalling PowerVault MD Storage SoftwareRun the file Uninstall Dell MD Storage Uninstalling PowerVault MD Storage Software From LinuxTable A-1. Host Server Vs. Storage Array Appendix-Manual Configuration of iSCSIDiscover the Storage Array Out-of-band Management Only Default Management Port SettingsAutomatic Storage Array Discovery Setting Up the ArrayManual Storage Array Discovery Table A-2. Initial Setup Tasks Dialog Box Purpose Configure the iSCSI Ports on the Storage ArrayAppendix-Manual Configuration of iSCSI Perform Target Discovery From the iSCSI Initiator Set the iSCSI initiator service to start automatically Configure Host Access Mutual Chap Understanding Chap AuthenticationWhat is CHAP? Target ChapChap Definitions Configure Chap Authentication on the Storage Array OptionalTable A-3. Chap Types Defined Description Table A-4. Chap Setting Option Description Configuring Target Chap Authentication on the Storage ArrayConfiguring Mutual Chap Authentication on the Storage Array Configure Chap Authentication on the Host Server OptionalIf you are using Windows Server 2008 Core version Add the target portal with Chap defined Discovery.sendtargets.auth.authmethod = Chap Connect to the Target Storage Array From the Host Server Local Adapter-Must be set to Microsoft iSCSI Initiator TCPPortNumberOfTargetPortal is For example, your log on command might look like this Optional Set Up In-Band Management Appendix-Using Internet Storage Naming Service Appendix-Using Internet Storage Naming Service Load Balance Policy Appendix-Load BalancingRound Robin With Subset Least Queue Depth With Subset Least Path Weight With SubsetIncreasing Bandwidth With Multiple iSCSI Sessions ISCSI Sessions TCP ConnectionsAppendix-Load Balancing Appendix-Load Balancing Appendix-Stopping and Starting iSCSI Services in Linux Appendix-Stopping and Starting iSCSI Services in Linux
Related manuals
Manual 22 pages 36.51 Kb Manual 268 pages 25.67 Kb

MD3200i, MD3220i specifications

The Dell MD3220i and MD3200i are part of Dell's extensive line of modular storage solutions, designed to support organizations in optimizing their data management and scalability requirements. These models offer reliable performance and flexible features, making them suitable for various workloads including virtualization, cloud storage, and disaster recovery.

One of the standout features of the MD3220i and MD3200i is their support for iSCSI storage networking. By utilizing the Internet Small Computer Systems Interface (iSCSI) protocol, these systems provide organizations with a cost-effective way to connect their storage over existing network infrastructure, enabling efficient data transfers and management.

Both models are equipped with dual controllers that ensure high availability and failover capabilities, which are crucial for meeting uptime requirements in mission-critical environments. The dual controllers also facilitate load balancing and increase overall system performance, as they allow multiple paths to the storage, enhancing I/O performance.

Scalability is another key characteristic of the MD3220i and MD3200i. These storage arrays can be expanded to meet growing storage demands, supporting up to 240TB of raw capacity with up to 16 additional expansion enclosures. This flexibility allows organizations to start with a smaller configuration and grow their storage capabilities without a complete overhaul of the existing infrastructure.

The units also support multiple disk types, including traditional spinning disks, solid-state drives (SSDs), and a combination of both. This versatility enables users to tailor storage configurations to their specific performance and budgetary needs. Furthermore, the systems feature advanced data management technologies such as snapshots and remote replication, providing essential tools for data protection.

With their ease of management, the MD3220i and MD3200i are designed for straightforward configuration and operation. The intuitive management interfaces allow IT professionals to monitor performance, configure storage, and manage data effectively, ensuring businesses can maintain optimal system availability.

In summary, the Dell MD3220i and MD3200i are robust, scalable, and versatile storage solutions that cater to diverse organizational needs. Their integrated technologies, such as iSCSI support, dual controller architecture, and advanced data management features, make them an ideal choice for modern data centers looking to enhance storage capabilities while ensuring reliability and performance.