Dell MD3200i, MD3220i manual For example, your log on command might look like this

Page 73

For example, your log on command might look like this:

iscsicli PersistentLoginTarget iqn.1984- 05.com.dell:powervault.6001372000ffe3332xx0000046 72edf2 3260 T 192.168.130.101 * * * 0x2 * * * * *

** * * 0

To view active sessions to the target, run the following command:

iscsicli SessionList

To support storage array controller failover, the host server must be connected to at least one iSCSI port on each controller. Repeatstep 3 for each iSCSI port on the storage array that you want to establish as a failover target. The Target_ Portal_Address is different for each port you connect to.

PersistentLoginTarget does not initiate a login to the target until after the system is rebooted. To establish immediate login to the target, substitute LoginTarget for PersistentLoginTarget.

:NOTE: See the Microsoft iSCSI Software Initiator 2.x User’s Guide for more information about the commands used in the previous steps. For more information about Windows Server 2008 Server Core, see the Microsoft Developers Network (MSDN) at microsoft.com.

If you are using a Linux Server:

In MDSM, the Configure iSCSI Host Ports displays the status of each iSCSI port you attempt to connect and the configuration state of all IP addresses. If either displays Disconnected or Unconfigured, respectively, check the following and repeat the iSCSI configuration steps:

Are all cables securely attached to each port on the host server and storage array?

Is TCP/IP correctly configured on all target host ports?

Is CHAP set up correctly on both the host server and the storage array?

To review optimal network setup and configuration settings, see "Guidelines for Configuring Your Network for iSCSI" on page 49.

Appendix—Manual Configuration of iSCSI

73

Image 73
Contents Deployment Guide 2011 Rev. A01 Contents Disk Configuration Utility ISCSI Configuration WorksheetMicrosoft Windows Host Setup Uninstalling Dell PowerVault MD StorageConfigure the iSCSI Ports on Uninstalling PowerVault MD Storage SoftwareConfigure Host Access Configure Chap Authentication onConnect to the Target Storage Array From Appendix-Load BalancingSystem Requirements IntroductionManagement Station Requirements Introduction to Storage Arrays Introduction Introduction Planning the Storage Configuration Hardware InstallationRedundant and Non-Redundant Configurations Connecting the Storage ArrayCabling the Storage Array Single Path Data Configurations Direct-Attached ConfigurationsFour Hosts Connected to a Single Controller Shows two hosts connected to a single controller array Eight Hosts in a Dual-Controller Configuration Dual-Path Data Configuration Four Hosts Connected to Two Controllers Four Hosts Connected in a Dual-Controller Configuration Network-Attached Configurations Servers Connected to a Single Controller Servers Connected to Two Controllers Cabling PowerVault MD1200 Series Expansion Enclosures Hardware Installation Click Tools→ Upgrade RAID Controller Module Firmware Click Advanced→ Maintenance→ Download→ EMM Firmware Installing PowerVault MD Storage Software Graphical Installation Recommended Select Install MD Storage Software Silent Installation Console InstallationUpgrading PowerVault MD Storage Software Installing PowerVault MD Storage Software Standard Terminology Used in iSCSI Configuration Definition Post Installation TasksBefore You Begin ISCSI Configuration Worksheet Chap Secret IPv4 SettingsMutual Chap Target Chap IPv6 SettingsFE80 0000 0000 Host Server Vs. Storage Array Configuring iSCSI on Your Storage ArrayManager Storage Array Configuration Host Configuration Host Connectivity Configuration Configure the Storage Array Using PowerVault Mdcu Post Installation Tasks Post Installation Tasks Post Installation Tasks Configure the Host Connectivity Using PowerVault Mdcu Source Port Selection for iSCSI Host Ports Automatic Selection Post Connection Establishment Steps Microsoft Windows Host Setup Guidelines for Configuring Your Network for iSCSIControl Panel, select Network connections Edit the /etc/sysconfig/network file Linux Host SetupHWADDR=XXXXXXXXXXXX GATEWAY=192.168.1.1 Click Change/Remove Uninstalling PowerVault MD Storage SoftwareRun the file Uninstall Dell MD Storage Uninstalling PowerVault MD Storage Software From LinuxTable A-1. Host Server Vs. Storage Array Appendix-Manual Configuration of iSCSIDiscover the Storage Array Out-of-band Management Only Default Management Port SettingsAutomatic Storage Array Discovery Setting Up the ArrayManual Storage Array Discovery Table A-2. Initial Setup Tasks Dialog Box Purpose Configure the iSCSI Ports on the Storage ArrayAppendix-Manual Configuration of iSCSI Perform Target Discovery From the iSCSI Initiator Set the iSCSI initiator service to start automatically Configure Host Access What is CHAP? Understanding Chap AuthenticationTarget Chap Mutual ChapChap Definitions Configure Chap Authentication on the Storage Array OptionalTable A-3. Chap Types Defined Description Table A-4. Chap Setting Option Description Configuring Target Chap Authentication on the Storage ArrayConfiguring Mutual Chap Authentication on the Storage Array Configure Chap Authentication on the Host Server OptionalIf you are using Windows Server 2008 Core version Add the target portal with Chap defined Discovery.sendtargets.auth.authmethod = Chap Connect to the Target Storage Array From the Host Server Local Adapter-Must be set to Microsoft iSCSI Initiator TCPPortNumberOfTargetPortal is For example, your log on command might look like this Optional Set Up In-Band Management Appendix-Using Internet Storage Naming Service Appendix-Using Internet Storage Naming Service Load Balance Policy Appendix-Load BalancingRound Robin With Subset Least Queue Depth With Subset Least Path Weight With SubsetIncreasing Bandwidth With Multiple iSCSI Sessions ISCSI Sessions TCP ConnectionsAppendix-Load Balancing Appendix-Load Balancing Appendix-Stopping and Starting iSCSI Services in Linux Appendix-Stopping and Starting iSCSI Services in Linux
Related manuals
Manual 22 pages 36.51 Kb Manual 268 pages 25.67 Kb

MD3200i, MD3220i specifications

The Dell MD3220i and MD3200i are part of Dell's extensive line of modular storage solutions, designed to support organizations in optimizing their data management and scalability requirements. These models offer reliable performance and flexible features, making them suitable for various workloads including virtualization, cloud storage, and disaster recovery.

One of the standout features of the MD3220i and MD3200i is their support for iSCSI storage networking. By utilizing the Internet Small Computer Systems Interface (iSCSI) protocol, these systems provide organizations with a cost-effective way to connect their storage over existing network infrastructure, enabling efficient data transfers and management.

Both models are equipped with dual controllers that ensure high availability and failover capabilities, which are crucial for meeting uptime requirements in mission-critical environments. The dual controllers also facilitate load balancing and increase overall system performance, as they allow multiple paths to the storage, enhancing I/O performance.

Scalability is another key characteristic of the MD3220i and MD3200i. These storage arrays can be expanded to meet growing storage demands, supporting up to 240TB of raw capacity with up to 16 additional expansion enclosures. This flexibility allows organizations to start with a smaller configuration and grow their storage capabilities without a complete overhaul of the existing infrastructure.

The units also support multiple disk types, including traditional spinning disks, solid-state drives (SSDs), and a combination of both. This versatility enables users to tailor storage configurations to their specific performance and budgetary needs. Furthermore, the systems feature advanced data management technologies such as snapshots and remote replication, providing essential tools for data protection.

With their ease of management, the MD3220i and MD3200i are designed for straightforward configuration and operation. The intuitive management interfaces allow IT professionals to monitor performance, configure storage, and manage data effectively, ensuring businesses can maintain optimal system availability.

In summary, the Dell MD3220i and MD3200i are robust, scalable, and versatile storage solutions that cater to diverse organizational needs. Their integrated technologies, such as iSCSI support, dual controller architecture, and advanced data management features, make them an ideal choice for modern data centers looking to enhance storage capabilities while ensuring reliability and performance.