Compatible Systems 2270R manual Connecting the Router to the Ethernet

Page 16

10

Chapter 3 - Network Installation

Connecting the Router to the Ethernet

If your twisted-pair hub is already in place, you can connect the router to an active network without interrupting network activity. The router must be powered off.

Connecting to Twisted-Pair Ethernet

Before connecting the router to twisted-pair cabling you need an unshielded twisted-pair cable that is already connected to your 10BaseT-compatible twisted-pair hub.

To connect the router to the twisted-pair network, simply plug the twisted-pair cable into the RJ-45 Ethernet connector on the back of the unit.

Connecting the Router to a T1 Line

To connect the router to the T1 line, you need a four wire jumper cable that is already connected to the RJ-45 jack which was installed by your telephone company. The router must be powered off. Simply plug the jumper cable into the RJ-45 WAN 0 connector on the back of the MicroRouter 2270R.

Connecting a Line Device to the Secondary Port

The MicroRouter 2270R supports lower speed synchronous/asynchro- nous operation over a secondary RS-232 connector (WAN 1). This port independently supports the PPP and Frame Relay link protocols.

Connecting Devices to the RS-232C Interface

This interface -- WAN 1 -- can be used to connect to synchronous or asynchronous line communications devices at rates up to 256Kbps (sync), or 230.4 Kbps (async). Examples include modems, leased or switched 56K CSU/DSU’s, and ISDN Terminal Adapters.

Note: If connecting to a synchronous device such as a CSU/DSU, Lthe router must first be configured for synchronous operation before connecting to the device. See Chapter 6 - Basic Configuration Guide for configuration information.

You may select either dial-on-demand, always up (i.e., redial if down), or leased line operation. This interface may also be set to receive ISDN or switched-56 incoming calls.

To connect a device, first make sure that both units are powered off. Then, simply connect the supplied RS-232 cable between the router and the device.

Image 16
Contents MicroRouter 2270R Installation Guide Page Introduction Network InstallationGetting Started Command Line Management Basic Configuration GuideFrame Relay Dlci Mappings IP Protocol Appendix a Shipping Defaults Systems Appendix E Terms and ConditionsAbout the MicroRouter 2270R IntroductionIntroduction MicroRouter 2270R Installation Overview Network Installation CompatiView Software InstallationCommand Line Preparation Basic Configuration GuidePage Warranty and Service Getting StartedFew Notes Please Read The ManualsWhat You Will Need To Get Started Needed For InstallationSupplied with the MicroRouter 2270R Ethernet Connection Requirements T1 Line Connection RequirementsOther Telco Line Connection Requirements 10Base-T Twisted-Pair EthernetRS-232 Interface Network Installation Placing the RouterConnecting the Router to the Ethernet Connecting the Router to a T1 LineConnecting a Line Device to the Secondary Port Connecting to Twisted-Pair EthernetConnecting an Out-of-Band Management Console Powering Up the RouterPage CompatiView for Windows Installation and OperationSystem Requirements Transport Protocols and CompatiView Command Line Management Out-of-Band Command Line ManagementTemporarily Reconfiguring a Host for Command Line Management Setting Up Telnet OperationSubnetMask, and IPBroadcast keywords in the IP Page Basic Configuration Guide Ethernet Interface ConfigurationIP Protocol IPX ProtocolRequired for IP Suggested for IPAppleTalk Protocol DECnet ProtocolInternal T1 CSU/DSU WAN 0 Physical Communications Settings WAN Interface ConfigurationRS-232 WAN 1 Physical Communications Settings Internal T1 CSU/DSU WAN 0 Link Configuration RS-232 WAN 1 Link ConfigurationSuggested for Dedicated/Leased Line Operation Required for Dedicated/Leased Line OperationSuggested for Dial-On-Demand Operation IPX Protocol DECnet Protocol Frame Relay Configuration Frame Relay Dlci MappingsRequired for IP Numbered Interface IPX Protocol AppleTalk Protocol Saving a Configuration File to Flash ROM Smds AddressingPage Default Password Appendix a Shipping DefaultsEthernet Interfaces WAN Interfaces Appendix B Connector and Cable Pin Outs Pin Outs for T1 Female Connector DTEPage Power On, No Traffic Ethernet Traffic Indicators Ethernet LED BarsWAN Indicators WAN LED Bar MicroRouter 2270R LED PatternsMicroRouter 2270R Switch Settings Appendix D Downloading Software From Compatible Systems Page Appendix E Terms Conditions Appendix E Terms and ConditionsAppendix E Terms and Conditions Appendix E Terms and Conditions

2270R specifications

The Compatible Systems 2270R is a state-of-the-art computing solution designed for organizations that demand efficiency and reliability in their operational tasks. Known for its versatility and performance, the 2270R has garnered attention for its robust features and advanced technologies.

One of the main highlights of the Compatible Systems 2270R is its powerful processing capabilities. Equipped with a high-performance multi-core processor, it ensures optimal performance for both single-threaded and multi-threaded applications. This makes it an ideal choice for demanding tasks such as data analysis, scientific computations, and real-time processing. The advanced architecture not only enhances the speed of operations but also improves energy efficiency.

The system comes standard with a generous amount of RAM, allowing for seamless multitasking. This means users can run multiple applications simultaneously without experiencing any slowdown. The ability to expand memory capacity also enables organizations to adapt the system to their growing needs.

Storage is another standout feature of the Compatible Systems 2270R. It offers multiple storage options, including high-speed solid-state drives (SSDs) and traditional hard disk drives (HDDs). This flexibility allows users to choose the best configuration for their specific requirements, whether they prioritize speed for faster data access or larger capacity for extensive data storage.

Connectivity options on the 2270R are extensive, featuring a variety of ports, including USB, HDMI, and Ethernet, among others. This ensures compatibility with a wide range of peripherals and network devices. The system also supports advanced wireless technologies, providing users with the flexibility to connect to networks seamlessly.

One of the defining characteristics of the Compatible Systems 2270R is its reliability. Built with high-quality components and robust thermal management, this system is designed to operate in various environments without failure. This reliability is essential for mission-critical applications where downtime can lead to significant consequences.

Furthermore, the Compatible Systems 2270R is designed with user accessibility in mind. It features an intuitive interface that simplifies the user experience, making it easier for both novice and experienced users to navigate its capabilities.

In summary, the Compatible Systems 2270R is a powerful and versatile computing solution that excels in processing power, memory capacity, storage options, and connectivity. Its reliability and user-friendly design make it a top choice for organizations looking to enhance their operational efficiency. Whether for advanced data processing or everyday tasks, the 2270R stands out as a dependable partner in the digital landscape.