Promise Technology S150 Troubleshooting & Tips, Motherboard Issues, Configuring PCI IRQ resources

Page 55

Chapter 6: Troubleshooting & Tips

This section is used to assist with troubleshooting conflicts and FastTrak S150 TX4 installation problems. Also refer to the README.TXT file on the FastTrak S150 TX4 driver and utility diskette for more recent information as well as the PromiseOnline services listed in Appendix B.

The section is divided into the following categories: Motherboard Issues, System CMOS Issues, Drive Errors, Operating System Errors, and Audio/Video Editing Tips.

Motherboard Issues

Freeing additional IRQ resources

Since the Promise card supports PCI Interrupt sharing, it is possible to use IRQs already assigned to another PCI card. Interrupt Sharing is not supported with onboard IDE controllers. If the onboard IDE controller(s) are not used, you may disable the controllers to free IRQ 14 and/or 15.

Configuring PCI IRQ resources

Setting the IRQ for a particular PCI slot will be different depending on the motherboard BIOS. This setting is usually made in the PCI Configuration and/or Plug and Play (PnP) section of the motherboard BIOS setup. There are three common methods that motherboard BIOS’s handle assignment of IRQs to PCI slots:

Specifically assigning an IRQ to a particular slot - You can tell the motherboard to use IRQ 10 for PCI slot 1, IRQ 11 for PCI slot 2, etc.

Listing which IRQs are available to be assigned to the PCI slots - This BIOS has an option where you specify 1st Available IRQ, 2nd Available IRQ, etc. The BIOS then scans the PCI slots for PCI cards and assigns these IRQs in the order that it finds the PCI cards.

Consult your motherboard manual for information that is specific to your motherboard.

Intermittent data problems

Overclocking the PCI bus may cause the system to hang or data corruption. If you experience either of these problems and you are overclocking the PCI bus, set the PCI bus back to its normal setting to see if this is causing the errors.

51

Image 55
Contents Fasttrak S150 TX4 Trademarks CopyrightImportant Data Protection Information Contents Page FastTrak S150 TX4 IntroductionPromise Array Management Utility PAM Features Benefits Key Features and BenefitsCompatibility Unpacking Your FastTrak Card InstallationInsert the FastTrak card into an open PCI slot Installing the FastTrak CardInstalling the Hard Drives FastTrak S150 TX4 card Creating Your Disk Array Creating a Performance Array Creating a Security Array with New Drives Creating a Security Array with an Existing Data Drive Seagate S380023AS Creating a Security Array with Quick Initialization Viewing FastTrak S150 TX4 Bios Screen Using FastBuild Configuration UtilityUsing the Main Menu Navigating the FastBuild Setup MenuOptimize Array for Creating Arrays AutomaticallyPerformance Security and Performance SecurityCreating Multiple Arrays Using a Hot Spare DriveViewing Drive Assignments Manually Creating an Array Selecting Stripe Block Selecting Array TypeAssigning Drives to Array Gigabyte BoundaryCreating a Striped Array Creating a Mirrored Array Using New DrivesAdding Fault Tolerance to an Existing Drive Drive Model Capacity MB How FastTrak S150 TX4 Orders Arrays Creating a Hot Spare Drive for Mirrored ArraysHow FastTrak S150 TX4 Saves Array Information Deleting an Array Array Stripe 160048 Rebuilding a Mirrored Array 80024 Page Procedure Number Installing Software DriversNew Windows XP Installation Confirming Windows XP Driver Installation Existing Windows XP InstallationNew Windows 2000 Installation Confirming Windows 2000 Driver Installation Existing Windows 2000 InstallationNew Windows ME Installation Confirming Windows ME Driver Installation Existing Windows ME InstallationNew Windows NT4.0 Installation Removing Driver from Windows NT4.0 Existing Windows NT4.0 InstallationNew Windows 98 Installation Confirming Windows 98 Driver Installation Existing Windows 98 InstallationPage About FastTrak S150 TX4 About Adapter BiosFastBuild Auto Menu Setup Disk Array ConceptsDisk Array Member RAID Level Performance Fault Capacity No. Tolerance DrivesDisk Array Terms Disk Array DescriptionStriping RAID About RAID LevelsData Mirror Disk Drives Mirroring RAIDStriping / Mirroring RAID 0+1 Failed Array Event Drives Status Why? About Dual Data RedundancyIntermittent data problems Troubleshooting & TipsMotherboard Issues Configuring PCI IRQ resourcesUsing an Onboard IDE Card with FastTrak S150 TX4 System Cmos IssuesSystem Cmos displays C or D drive failure during Startup Drive-Related ErrorsCritical Array Status Error Reported during Boot Drive cannot be formed into an arrayUnable to Partition or Format Array Cannot Rebuild Mirrored RAID 1 Array Promise Windows driver does not appear in Device Manager Operating System-Related IssuesTroubleshooting & Tips Optimize Array for Performance Performance TipsChange Setting of PCI Bus Utilization Page Pre-Installation Appendix a Frequently Asked QuestionsRAID 0 Stripe Drive IssuesRAID 1 Mirror Appendix a FAQs Post-Installation Installation IssuesEuropean Tech Support Technical Support ServicesAppendix B Technical Support USA Tech Support CenterChina Office Pacific Rim Sales OfficeDisclaimer of other warranties Limited WarrantyYour Responsibilities Returning Product for Repair

S150 specifications

Promise Technology S150 is an advanced storage solution designed to meet the data management needs of modern businesses. This high-performance storage appliance is characterized by its scalability, reliability, and user-friendly management interface, making it an optimal choice for organizations looking to optimize their data storage strategies.

One of the standout features of the S150 is its support for multiple RAID levels, including RAID 0, 1, 5, 6, and 10. This ensures that businesses can tailor their storage configurations based on their specific redundancy and performance requirements. The S150's software-defined storage capabilities provide flexibility in allocating resources, enabling organizations to manage their data efficiently and improve overall performance.

In terms of connectivity, the Promise S150 offers a range of options, including high-speed 10GbE and Fibre Channel interfaces. These technologies ensure that data transfer rates remain high, minimizing latency and allowing seamless access to applications and data. Additionally, the device supports hot-swappable drives, allowing users to replace or upgrade components without downtime, further enhancing productivity.

The management of the S150 is simplified through the Promise Management software, which provides intuitive controls and monitoring capabilities. Users can easily configure storage settings, monitor performance metrics, and maintain data integrity using the built-in tools. The software's graphical user interface makes it straightforward even for those without extensive IT experience, reducing the administrative burden on staff.

Another notable characteristic of the S150 is its robust security features. It provides options for data encryption both at rest and in transit, ensuring that sensitive information is protected against unauthorized access. Advanced user authentication protocols further enhance security, making it suitable for enterprises dealing with confidential data.

The S150 is also designed with energy efficiency in mind. Its intelligent cooling system and power management features help to reduce overall energy consumption, which is crucial for organizations looking to lower operational costs and reduce their environmental impact.

In summary, Promise Technology S150 stands out in the storage market due to its combination of scalability, versatility, and robust management features. With its support for multiple RAID configurations, high-speed connectivity options, intuitive management software, and strong security protocols, the S150 is well-equipped to support the data demands of businesses today and into the future. It represents a reliable and efficient solution for those looking to enhance their data storage infrastructure.