Boot
Message | Description |
|
|
Boot Failure... | This is a generic message indicating the BIOS could not boot from a particular |
| device. This message is usually followed by other information concerning the |
| device. |
|
|
Invalid Boot Diskette | A diskette was found in the drive, but it is not configured as a bootable diskette. |
|
|
Drive Not Ready | The BIOS was unable to access the drive because it indicated it was not ready for |
| data transfer. This is often reported by drives when no media is present. |
|
|
A: Drive Error | The BIOS attempted to configure the A: drive during POST, but was unable to |
| properly configure the device. This may be due to a bad cable or faulty diskette |
| drive. |
|
|
B: Drive Error | The BIOS attempted to configure the B: drive during POST, but was unable to |
| properly configure the device. This may be due to a bad cable or faulty diskette |
| drive. |
|
|
Insert BOOT diskette | The BIOS attempted to boot from the A: drive, but could not find a proper boot |
in A: | diskette. |
| Reboot and Select proper Boot device or Insert Boot Media in selected Boot device |
| BIOS could not find a bootable device in the system and/or removable media drive |
| does not contain media. |
|
|
Reboot and select | BIOS could not find a bootable device in the system and/or removable |
proper boot device or | media drive does not contain media. |
Insert boot media in |
|
selected boot device |
|
|
|
NO ROM BASIC | This message occurs on some systems when no bootable device can be detected. |
|
|
Storage Device
Message | Description |
|
|
Primary Master Hard | The IDE/ATAPI device configured as Primary Master could not be properly |
Disk Error | initialized by the BIOS. This message is typically displayed when the BIOS is trying |
| to detect and configure IDE/ATAPI devices in POST. |
|
|
Primary Slave Hard | The IDE/ATAPI device configured as Primary Slave could not be properly initialized |
Disk Error | by the BIOS. This message is typically displayed when the BIOS is trying to detect |
| and configure IDE/ATAPI devices in POST. |
|
|
Secondary Master | The IDE/ATAPI device configured as Secondary Master could not be properly |
Hard Disk Error | initialized by the BIOS. This message is typically displayed when the BIOS is trying |
| to detect and configure IDE/ATAPI devices in POST. |
|
|
Secondary Slave | The IDE/ATAPI device configured as Secondary Slave could not be properly |
Hard Disk Error | initialized by the BIOS. This message is typically displayed when the BIOS is trying |
| to detect and configure IDE/ATAPI devices in POST. |
|
|
3rd Master Hard Disk | The IDE/ATAPI device configured as Master in the 3rd IDE controller could not be |
Error | properly initialized by the BIOS. This message is typically displayed when the BIOS |
| is trying to detect and configure IDE/ATAPI devices in POST. |
|
|
3rd Slave Hard Disk | The IDE/ATAPI device configured as Slave in the 3rd IDE controller could not be |
Error | properly initialized by the BIOS. This message is typically displayed when the BIOS |
| is trying to detect and configure IDE/ATAPI devices in POST. |
|
|
4th Master Hard Disk | The IDE/ATAPI device configured as Master in the 4th IDE controller could not be |
Error | properly initialized by the BIOS. This message is typically displayed when the BIOS |
| is trying to detect and configure IDE/ATAPI devices in POST. |
|
|
4th Slave Hard Disk | The IDE/ATAPI device configured as Slave in the 4th IDE controller could not be |
Error | properly initialized by the BIOS. This message is typically displayed when the BIOS |
| is trying to detect and configure IDE/ATAPI devices in POST. |
|
|
Packard Bell oneTwo M3600 AIO Computer Service Guide | 49 |