Silex technology C-6700WG setup guide Setup Guide

Setup Guide

Step 1 : Con￿gure the Network

This Setup Guide explains how to con￿gure C-6700WG (this product) to be used in a wireless LAN environment.

Important:

The print server only needs to be configured on one computer.

After setup is complete, go to:

‘Step 2: Install the Applications’ for each computer that will use the printer.

This product has 3 methods of initial con￿guration as listed below:

-Con￿guration through a wireless LAN

-Con￿guration through a wired LAN

-Con￿guration using a USB memory

This Setup Guide describes how to con￿gure this product through a wireless LAN or wired LAN.

For other con￿guration methods, please refer to the users manual.

Perform the factory default con￿guration according to the connection between this product and the PC.

-To perform the factory default con￿guration with a wireless LAN connection, refer to Con￿gure Through a Wireless LAN.

-To perform the factory default con￿guration with a wired LAN connection, refer to

Con￿gure Through a Wired LAN.

If this product has been used in another network, reset it to the factory default settings.

For details on the factory default con￿guration, refer to To reset to the factory default settings.

To reset to the factory default settings

1.Remove the AC plug from the electric outlet.

2.Push and hold the button on the print server while re-inserting the AC plug into the electric outlet. Continue holding.

3.The Status LED(Orange) will light when the factory default con￿guration settings have been restored. Release the push switch.

Contents			W A 0 3 7 9 0 X X
C-6700WG	Power Supply	Stand
CX User Software	Rubber Feet	Setup Guide		Warranty Booklet

When the product is placed in the horizontal (side) position, please use the rubber feet provided to prevent the unit from sliding. Place one on each corner.

For User Registration

http://www.silexamerica.com/register/

Con￿gure Through a Wireless LAN

1.

The following item is required:

-USB cable

Use to connect this product and a printer.

There is no need to purchase a new USB cable when a cable was bundled with the printer to be connected to this product.

Install the printer driver on your PC.

For details, refer to the manual that came with your printer.

(Install the printer driver on your PC and make sure you can print with a directly attached USB connection from your computer before using this product.)

2.

Connect the AC adapter to this product and the power plug to the outlet.

(Do not connect the printer to this product yet. Printer will be connected in ‘18’)

3. 4. 5.

Verify the Wireless LED(Green) blinks. Insert the CD-ROM (CX User Software) into your Windows PC. Check the message and click OK.

Customer Support

USA : silex technology america, Inc.

E-mail : support@silexamerica.com

URL : http://www.silexamerica.com/

Phone: 801-748-1199

US Toll Free Phone: 866-765-8761

Note: A more detailed manual including troubleshooting tips can be found on the CD (Insert the CD, and click on Manual when the Autorun menu appears) of this product.

Safety instructions are noted in the Readme ￿le on the CX User Software . Be sure to read them before using this product.

-Safety instructions regarding the radio waves

Please note the following instructions:

-Do not use this product near medical devices such as a heart pacemaker. The radio wave generated by this product may interfere with the operation of these devices and may threaten one's life.

-Do not use this product near microwave ovens. The radio wave used by microwave ovens may cause interference to this product.

Introduction

6. 7. 8. 9. 10.

Startup menu is displayed.	Click Wireless.	* In a Windows XP (SP2 or higher) or Vista environment, the above message	CX Wireless Setup screen is displayed.	Read the SOFTWARE LICENSE AGREEMENT and click	If the screen above is displayed, select the wireless
Click Print Server Setup.		will be displayed. Select. Yes	Check the notes on the screen and select	Yes.	network card to be used and click OK.
		* The User Account Control screen is displayed when con￿guration is performed	Con￿gure print server wirelessly from your
		on Windows Vista. Select Continue.			* This screen is displayed only when two or more
			computer and click Next.
					network cards are installed on your PC.
					Select this product and click Next.

11. 12. 13. 14.

Collect wireless LAN setting information

To use this product over the wireless LAN network, you need to con￿gure wireless LAN settings as appropriate for your network. This information needs to be identical to the communication devices such as an access point.

Please collect the following information before the setup.

If the screen above is displayed, you need to change the wireless settings on the PC manually.

Read the message and click OK.

*If you use Windows XP or Vista and the setup utility automatically changed the wireless settings on the PC, this screen is not displayed.

If the wireless settings on the PC di￿er from the

con￿guration information on the screen above, change the PC wireless settings to match those displayed on the screen.

Verify the wireless settings on the PC and click Next.

*Please refer to your wireless network adapter documentation for instructions on how to temporarily change your computer’s wireless settings to match those of the print server.

Important: When you make this temporary change, your computer will no longer be connected to the wireless network or Internet. After you have completed the setup for the print server, you will need to change your computer’s wireless settings back to their current settings. Please make sure you write down the settings for your wireless network before you make these changes for the print server configuration.

Select a product to be con￿gured and click Next.

*If your product is not displayed on the list, click Refresh.

*If multiple products are displayed in the list, check the Ethernet Address on the label of this product.

Select Get IP Address Automatically and click Next.

Select the SSID for your home or o￿ce wireless network. If your network is security enabled, enter the network key or password and con￿rm it. Click Next.

*If the wireless network that you wish to use is not shown in the list, click Detailed Con￿g and con￿gure each setting.

	Write down your network con￿guration
Wireless mode	Ad hoc (ch. ) / Infrastructure

SSID

Encryption	WEP	/ WPA / WPA2
method
	(Open / Shared)

Encryption method

WEP KEY or Pre-Shared Key

15.	16.	<< If you did not need to change the
		wireless settings on the PC manually
		in ‘11’, this screen will appear	>>

Con￿rm the con￿guration parameters and	Select Yes and click Finish.
click Execute.	* Application install screen will be displayed as
	shown in Step 2 - 3.

<<If you changed the wireless settings on the PC manually in ‘11’, this

screen will appear >>

Click Finish.

Change the wireless settings on the PC (that you have manually changed) back to the previous settings written down in ‘11’.

17. 18.

To ensure these settings take e￿ect,	Connect the printer to be shared over the network along
unplug the AC adapter from the electrical	with this product via a USB cable and insert the power
outlet and then plug it back in.	plug of this product into the outlet.

The initial con￿guration of this product is complete and you do not need to con￿gure the print server any more.

After setup is complete on one computer, each user that wants to use the Canon printer:

Go to

Step 2: Install the Applications

on the next page

Note: If you manually changed the wireless settings at ‘11’ on your PC, go straight to

‘3’ in Step 2.