Emotiva manual Troubleshooting Guide, No Sound from one or more speakers connected to the RPA-1

Page 22

Troubleshooting Guide

The Emotiva RPA-1 is expertly designed and built to provide years of trouble-free performance. Most problems that occur can usually be solved by checking your setup or making sure that the audio and video components connected to the RPA-1 are on and fully operational. The following information will help you deal with common setup problems you may experience during normal use of your unit. If problems persist, contact your Emotiva Dealer for help.

No Sound (from one or more speakers connected to the RPA-1)

•Speaker cables may have come undone. Turn off your system and check the cables, and tighten the amplifier and speaker binding posts.

•Damaged audio cable.

•The preamplifier volume level is low for the channels concerned. Recheck the preamplifier calibration procedure.

•A preamplifier Mute switch may be on, or an external processor loop or a tape monitor loop is engaged.

•If the unit is not on, the ON/OFF switch on the RPA-1 might be in the off position.

•The internal fuse on the unit may have blown. If so, replace only with rated fuse size and type.

The amplifier shuts down often or the line circuit breaker trips often

•Check that the positive and negative speaker wires are not shorted together.

•Make sure that no speakers are shorted internally. If you have an ohm-meter, disconnect the speaker wires and measure the resistance between the speaker’s positive and negative terminals. If the reading is less than 3.2 ohms on either channel, the speakers may have an internal short or you have connected several using a parallel configuration that yields too low an impedance. Measure all speakers and check their impedance specifications. If necessary, review the “Series and Parallel Connections” section of this manual.

•If you have connected speakers in parallel, the overall impedance may be too low. It is recommended that you rearrange the speakers in series to increase the overall impedance, thus taking some of the load off the amplifier.

•Make sure that the amplifier has good ventilation and is not overheating. Allow good airflow underneath wherever possible. If the amplifier is in a closed rack, open up the rear panel or use a quiet fan for improved ventilation.

Poor Bass Performance From Full Range Speakers connected to the RPA-1

•Make sure that your preamp does not have the bass (tone control) level turned down.

•If the preamplifier has a HPF, make sure that it has been correctly set. If you are not using a subwoofer, set the high pass filter to “BYPASS” (if available) or just use full range outputs into RPA-1 so that there is no path through a crossover and the speakers will play full range.

•Check that the speaker wires have been connected correctly: Make sure that the positive of each speaker connects to a positive output of the amplifier, and the negative of each speaker connects to a negative output. If one speaker is wired incorrectly, than it will be “out of phase” with the others, resulting in poor bass performance. DOUBLE CHECK ALL THE SPEAKER CONNECTIONS!!

Page 22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents USER’S Guide Table of Contents RPA-1 Technical Specifications Trademark Disclosure Safety Precautions Page NEC National Electrical Code Standards Antenna Grounding Outside the HouseThank You for your RPA-1 Purchase Inventory Unpacking the RPA-1Recording the Serial Number Emotiva RPA-1 Reference Power Amplifier RPA-1 Front Panel LayoutRPA-1 Rear Panel Layout RCA Audio InputsAC Power Considerations Installation and ConnectionsPhysical Placement Output Connection Considerations Input Connection ConsiderationsConnection Tips for Superior Sound Connection of a Preamp Level Device using XLR Inputs Connection DiagramsConnecting a Preamp Connection of a Preamp Level Device using RCA InputsConnecting Speakers Connection of a Stereo SpeakersBiamped Connections Low Pass and High Pass 12V Trigger Connections Series Series and Parallel Speaker ConnectionsParallel Technical Note about Multiple Speaker Connections Speaker Placement Tips Tips Before BeginningFront Speakers Subwoofer Location for 2.1 SystemsBass music Troubleshooting Guide No Sound from one or more speakers connected to the RPA-1Turn-on and turn-off thumps Hum Noises in the SpeakersRED light on the front panel blinks from blue to red Problems with the whole Audio SystemOther Probable Causes of Noise RED light on the front panel is illuminated solid redRPA-1 Technical Specifications Raw Weight Shipping Weight DimensionsTrademark Disclosure Emotiva DisclosureService Assistance for the RPA-1 Limited WarrantyEmotiva Franklin, TN

RPA-1 specifications

The Emotiva RPA-1 is a high-performance power amplifier designed for audio enthusiasts who demand exceptional sound quality and reliability. This amplifier is a part of Emotiva’s RPA series, known for their outstanding engineering and sonic performance. The RPA-1 delivers impressive power output, with the ability to drive demanding speakers effortlessly, making it ideal for both music and home theater applications.

One of the main features of the RPA-1 is its robust power output. It provides 200 watts per channel into 8 ohms and an even more powerful 400 watts per channel into 4 ohms, ensuring that it can handle dynamic music passages and movie soundtracks with ease. This amplifier employs Class AB amplification technology, which combines the benefits of both Class A and Class B amplifiers, resulting in low distortion, high efficiency, and a very clean sound.

The RPA-1 is equipped with a high-quality, custom-designed power supply, which features a large toroidal transformer and multiple large filter capacitors. This design ensures that there is ample power for transient peaks in the audio signal, leading to improved dynamics and headroom. The amplifier also includes a sophisticated protection circuit to prevent damage from short circuits or overheating, ensuring longevity and reliability.

Another characteristic of the Emotiva RPA-1 is its exceptional build quality. The chassis is constructed from heavy-duty steel, providing a solid and stable foundation that minimizes resonances. The sleek, modern design features a brushed aluminum front panel with easy-to-read indicators, creating an aesthetically pleasing addition to any audio setup.

In terms of connectivity, the RPA-1 features multiple RCA inputs for connecting to various audio sources, as well as binding post outputs for speaker connections. This versatility allows users to integrate the amplifier into a wide range of systems, from stereo setups to multi-channel home theaters.

Overall, the Emotiva RPA-1 is a powerful, reliable, and versatile amplifier that delivers exceptional audio performance. Its combination of high power output, robust build quality, and advanced technologies makes it an excellent choice for audiophiles and home theater enthusiasts alike. Whether you are listening to music or watching movies, the RPA-1 is sure to provide an immersive and satisfying audio experience.
Top Page Image Contents