Maxtor STM3160215AS, STM3160815AS, STM3250310AS Environmental protection, Corrosive environment

Page 34

2.14Environmental protection

Maxtor designs its products to meet environmental protection requirements worldwide, including regulations restricting certain chemical substances.

2.14.1European Union Restriction of Hazardous Substances (RoHS) Directive

Seagate designs its products to meet environmental protection requirements worldwide, including regulations restricting certain chemical substances. This drive is manufactured with components and materials that comply with the RoHS Directive.

2.14.2China Restriction of Hazardous Substances (RoHS) Directive

2.14.2中国限制危险物品的指令

This product has an Environmental Protection Use Period (EPUP) of 20 years. The following table contains information mandated by China's "Marking Requirements for Control of Pollution Caused by Electronic Information Products" Standard.

"O" indicates the hazardous and toxic substance content of the part (at the homogenous material level) is lower than the threshold defined by the China RoHS MCV Standard.

“O”表示该部件（于同类物品程度上）所含的危险和有毒物质低于中国RoHS MCV标准所定义的门槛值。

"X" indicates the hazardous and toxic substance content of the part (at the homogenous material level) is over the threshold defined by the China RoHS MCV Standard.

“X”表示该部件（于同类物品程度上）所含的危险和有毒物质超出中国RoHS MCV标准所定义的门槛值。

2.15Corrosive environment

Maxtor electronic drive components pass accelerated corrosion testing equivalent to 10 years exposure to light industrial environments containing sulfurous gases, chlorine and nitric oxide, classes G and H per ASTM B845. However, this accelerated testing cannot duplicate every potential application environment. Users should use caution exposing any electronic components to uncontrolled chemical pollutants and corrosive chemicals as electronic drive component reliability can be affected by the installation environment. The silver, copper, nickel and gold films used in Maxtor products are especially sensitive to the presence of sulfide, chloride, and nitrate contaminants. Sulfur is found to be the most damaging. In addition, electronic components should never be exposed to condensing water on the surface of the printed circuit board assembly (PCBA) or exposed to an ambient relative humidity greater than 95%. Materials used in cabinet fabrication, such as vulcanized rubber, that can outgas corrosive compounds should be minimized or eliminated. The useful life of any electronic equipment may be extended by replacing materials near circuitry with sulfide-free alternatives.

28

DiamondMax 21 Serial ATA Product Manual, Rev. C

Page 33 Page 35
Image 34
Page 33 Page 35
Contents DiamondMax Revision status summary sheet Contents DiamondMax 21 Serial ATA Product Manual, Rev. C List of Figures Typical 5V startup and operation current profilePage Introduction About the Serial ATA interface Drive specifications Specification summary tablesDrive specifications summary for 500 Gbyte models Drive specification STM3500630ASYes Drive specifications summary for 320 Gbyte models Drive specification STM3320820AS STM3320620ASDiamondMax 21 Serial ATA Product Manual, Rev. C Drive specifications summary for 250 Gbyte models Drive specification STM3250824AS STM3250820AS STM3250310ASDiamondMax 21 Serial ATA Product Manual, Rev. C Drive specifications summary for the 160 Gbyte models Drive specification STM3160815AS STM3160215ASDiamondMax 21 Serial ATA Product Manual, Rev. C Drive specifications summary for the 80 Gbyte model Drive specification STM380815AS STM380215ASYears on distribution units Drive specifications summary for the 40 Gbyte model Drive specification STM340215ASDiamondMax 21 Serial ATA Product Manual, Rev. C Formatted capacity Default logical geometryLBA mode Cylinders Read/write heads Sectors per track 16,383STM3160815AS, STM3160215AS Recording and interface technologySTM3250310AS STM380815AS, STM380215AS and STM340215AS Physical characteristics Start/stop times Power specificationsSeek time STM3250820AS 500-320 GB STM3250824AS STM3250310AS 160 40 GBIdle mode power Power consumptionSpinup power Seek modeConducted noise Typical current profilesVoltage tolerance Idle mode Power-management modesActive mode Sleep modeEnvironmental specifications Operating vibration Nonoperating shockVibration Nonoperating vibrationFluid Dynamic Bearing FDB motor acoustics AcousticsElectromagnetic immunity Radio frequency environmentsAgency certification Safety certificationReliability Electromagnetic compatibilityAustralian C-Tick N176 Korean RRLFCC verification Corrosive environment Environmental protectionChina Restriction of Hazardous Substances RoHS Directive Configuring and mounting the drive Handling and static-discharge precautionsConfiguring the drive Serial ATA cables and connectorsDrive mounting Drive dimensions for 40-160 GB and STM3250310AS models Serial ATA Sata interface Hot-Plug compatibilitySignal Serial ATA device plug connector pin definitionsSerial ATA connector pin definitions Pin Function DefinitionSupported ATA commands Supported ATA commandsCommand name Command code in hex F4H Identify Device command Word Description ValueXx07H 100 Description if bit is set to Bit Word Bit WordSet Features command Set Features command valuesM.A.R.T. commands 3 S.M.A.R.T. commandsCode in features register A.R.T. command Maxtor support services DiamondMax 21 Serial ATA Product Manual, Rev. C Index ITE Page DiamondMax 21 Serial ATA Product Manual, Rev. C Page Seagate Technology LLC
Top Page Image Contents