Maxtor STM3250820AS Serial ATA device plug connector pin definitions, Pin Function Definition

Page 40

4.2Serial ATA device plug connector pin definitions

Table 10 summarizes the signals on the Serial ATA interface and power connectors..

Table 10:	Serial ATA connector pin definitions

Segment	Pin	Function	Definition

	S1	Ground	2nd mate

	S2	A+	Differential signal pair A from Phy

	S3	A-

	S4	Ground	2nd mate

	S5	B-	Differential signal pair B from Phy

	S6	B+
Signal
Signal	S7	Ground	2nd mate

		Key and spacing separate signal and power segments

	P1	V33	3.3V power
	P2	V33	3.3V power
	P3	V33	3.3V power, pre-charge, 2nd mate
	P4	Ground	1st mate

	P5	Ground	2nd mate

	P6	Ground	2nd mate

	P7	V5	5V power, pre-charge, 2nd mate
Power	P8	V5	5V power
	P9	V5	5V power
	P10	Ground	2nd mate

	P11	Ground or LED signal	If grounded, drive does not use deferred spin

	P12	Ground	1st mate.

	P13	V12	12V power, pre-charge, 2nd mate
	P14	V12	12V power
	P15	V12	12V power

Notes:

1.All pins are in a single row, with a 1.27 mm (0.050”) pitch.

2.The comments on the mating sequence apply to the case of backplane blindmate connector only. In this case, the mating sequences are:

•the ground pins P4 and P12.

•the pre-charge power pins and the other ground pins.

•the signal pins and the rest of the power pins.

3.There are three power pins for each voltage. One pin from each voltage is used for pre-charge when installed in a blind-mate backplane configuration.

4.All used voltage pins (Vx) must be terminated.

34	DiamondMax 21 Serial ATA Product Manual, Rev. C

Image 40

Contents DiamondMax Revision status summary sheet Contents DiamondMax 21 Serial ATA Product Manual, Rev. C List of Figures Typical 5V startup and operation current profilePage Introduction About the Serial ATA interface Drive specifications Specification summary tablesDrive specifications summary for 500 Gbyte models Drive specification STM3500630ASYes Drive specifications summary for 320 Gbyte models Drive specification STM3320820AS STM3320620ASDiamondMax 21 Serial ATA Product Manual, Rev. C Drive specifications summary for 250 Gbyte models Drive specification STM3250824AS STM3250820AS STM3250310ASDiamondMax 21 Serial ATA Product Manual, Rev. C Drive specifications summary for the 160 Gbyte models Drive specification STM3160815AS STM3160215ASDiamondMax 21 Serial ATA Product Manual, Rev. C Drive specifications summary for the 80 Gbyte model Drive specification STM380815AS STM380215ASYears on distribution units Drive specifications summary for the 40 Gbyte model Drive specification STM340215ASDiamondMax 21 Serial ATA Product Manual, Rev. C Default logical geometry LBA modeFormatted capacity Cylinders Read/write heads Sectors per track 16,383STM3160815AS, STM3160215AS Recording and interface technologySTM3250310AS STM380815AS, STM380215AS and STM340215AS Physical characteristics Power specifications Seek timeStart/stop times STM3250820AS 500-320 GB STM3250824AS STM3250310AS 160 40 GBPower consumption Spinup powerIdle mode power Seek modeConducted noise Typical current profilesVoltage tolerance Power-management modes Active modeIdle mode Sleep modeEnvironmental specifications Nonoperating shock VibrationOperating vibration Nonoperating vibrationAcoustics Electromagnetic immunityFluid Dynamic Bearing FDB motor acoustics Radio frequency environmentsSafety certification ReliabilityAgency certification Electromagnetic compatibilityAustralian C-Tick N176 Korean RRLFCC verification Corrosive environment Environmental protectionChina Restriction of Hazardous Substances RoHS Directive Configuring and mounting the drive Handling and static-discharge precautionsConfiguring the drive Serial ATA cables and connectorsDrive mounting Drive dimensions for 40-160 GB and STM3250310AS models Serial ATA Sata interface Hot-Plug compatibilitySerial ATA device plug connector pin definitions Serial ATA connector pin definitionsSignal Pin Function DefinitionSupported ATA commands Supported ATA commandsCommand name Command code in hex F4H Identify Device command Word Description ValueXx07H 100 Description if bit is set to Bit Word Bit WordSet Features command Set Features command valuesM.A.R.T. commands 3 S.M.A.R.T. commandsCode in features register A.R.T. command Maxtor support services DiamondMax 21 Serial ATA Product Manual, Rev. C Index ITE Page DiamondMax 21 Serial ATA Product Manual, Rev. C Page Seagate Technology LLC