Maxtor STM3160813AS, STM31000334AS, STM3320614AS manual Set Features command values

Page 39

4.3.2Set Features command

This command controls the implementation of various features that the drive supports. When the drive receives this command, it sets BSY, checks the contents of the Features register, clears BSY and generates an inter- rupt. If the value in the register does not represent a feature that the drive supports, the command is aborted. Power-on default has the read look-ahead and write caching features enabled. The acceptable values for the Features register are defined as follows:

Table 9: Set Features command values

02H	Enable write cache (default).
03H	Set transfer mode (based on value in Sector Count register).
	Sector Count register values:
	00H	Set PIO mode to default (PIO mode 2).
	01H	Set PIO mode to default and disable IORDY (PIO mode 2).
	08H	PIO mode 0
	09H	PIO mode 1
	0AH	PIO mode 2
	0BH	PIO mode 3
	0CH	PIO mode 4 (default)
	20H	Multiword DMA mode 0
	21H	Multiword DMA mode 1
	22H	Multiword DMA mode 2
	40H	Ultra DMA mode 0
	41H	Ultra DMA mode 1
	42H	Ultra DMA mode 2
	43H	Ultra DMA mode 3
	44H	Ultra DMA mode 4
	45H	Ultra DMA mode 5
	46H	Ultra DMA mode 6
10H	Enable use of SATA features
55H	Disable read look-ahead (read cache) feature.
82H	Disable write cache
90H	Disable use of SATA features
AAH	Enable read look-ahead (read cache) feature (default).
F1H	Report full capacity available

Note. At power-on, or after a hardware or software reset, the default values of the features are as indi- cated above.

DiamondMax 22 Serial ATA Product Manual, Rev. A

33

Image 39

Contents STM31000334AS STM3320614AS STM3160813AS DiamondMax 22 Serial ATARevision Date Sheets affected or comments Rev. a 11/04/08 Initial releaseContents DiamondMax 22 Serial ATA Product Manual, Rev. a Typical 5V startup and operation current profile List of FiguresPage Introduction About the Serial ATA interface Drive specifications Drive specifications summary for 1000 Gbyte models DiamondMax 22 Serial ATA Product Manual, Rev. a Drive specifications summary for 320 and 160 Gbyte models DiamondMax 22 Serial ATA Product Manual, Rev. a Recording and interface technology Default logical geometryLBA mode Formatted capacityPhysical characteristics Seek timeTypical seek times msec Read Write Start/stop times Power specificationsDC power requirements Typical 12V startup and operation current profile Typical 5V startup and operation current profileSleep mode Power-management modesActive mode Idle modeEnvironmental specifications 160 GB models ShockOperating shock Nonoperating shock GB modelsTest for Prominent Discrete Tones PDTs AcousticsElectromagnetic immunity Fluid Dynamic Bearing FDB motor acousticsElectromagnetic compatibility Safety certificationReliability Agency certificationKorean RRL Australian C-Tick N176FCC verification China Restriction of Hazardous Substances RoHS Directive Environmental protection13.2 Corrosive environmentDiamondMax 22 Serial ATA Product Manual, Rev. a Handling and static-discharge precautions Configuring and mounting the driveSerial ATA cables and connectors Configuring the driveDrive mounting Mounting dimensions 1000 GB modelsMounting dimensions 320 and 160 GB models Hot-Plug compatibility Serial ATA Sata interfacePin Function Definition Serial ATA device plug connector pin definitionsSerial ATA connector pin definitions SignalSupported ATA commands Supported ATA commandsCommand name Command code in hex F4H Word Description Value Identify Device commandXx07H Bit Word Description if bit is set to Bit WordWord Set Features command values Set Features command3 S.M.A.R.T. commands M.A.R.T. commandsCode in features register A.R.T. command Technical Support Seagate Technology support servicesInternet Presales SupportWarranty Service Data Recovery Services Authorized Service CentersData Recovery Services Call Center Toll-free Direct dial Index ITE Page DiamondMax 22 Serial ATA Product Manual, Rev. a Page Seagate Technology LLC