Maxtor 5T010H1, 5T060H6, 5T020H2, 5T040H4, 5T030H3 InitializationCommands, Or D ENT Desc Ription

Page 51

INTERFACE COMMANDS

InitializationCommands

Identify Drive

Allows the host to receive parameter information from the drive.

When the command is received, the drive:

1.Sets BSY,

2.Stores the required parameter information in the sector buffer,

3.Sets the DRQ bit and

4.Generates an interrupt.

The host may then read the information out of the sector buffer. Parameter words in the buffer follow. Note that all reserved bits or words should be zeroes.

W OR D	CONT ENT DESC RIPTION
0	General configuration
	15 = device (0 = ATA device, 1 = ATAPI)
	14 -8 = retired
	7, 1 = removable media device
	6, 1 = not removable controller and/or device
	5-3 = retired
	2 = response incomplete
	1 = retired
	0 = reserved
1	Number of logical cylinders
2	Reserved
3	Number of logical heads
4-5	Retired
6	Number of logical sectors per logic al track
7-8	Reserved
9	Retired
10 - 19	Drive serial number (20 ASCII characters )
20 - 21	Retired
22	Obsolete
23 - 26	F irmware revision (8 ASCII characters )
27 - 46	Model number (40 ASCII characters )
47	Maximum number of sectors that c an be transferred per interrupt on read and write multiple commands
48	Reserved
49	C apabilities
	15 - 14 = reserved
	13 = s tandby timer (1 = values as specified in this s tandard are s upported, 0 = values are Maxtor specific )
	12 = reserved (advanc ed PIO mode support)
	11, 1 = IORD Y supported, 0 = IORDY may be supported
	10, 1 = IORDY can be disabled
	9-8 = shall be set to one. Us ed by Identify Packet Device comm and .
	7-0 = not us ed

7 – 10

Image 51

Contents Corporate Headquarters REV EC N O SEC Tion Desc Ription ATE U T I O N Before You BeginContents Handling and Installation Product SpecificationsInterface Commands AT Interface DescriptionHost Software Interface Glossary Service and SupportFigures Abbreviations IntroductionMaxtorCorporation ManualOrganizationConventions Product Description KeyFeaturesProduct Features Functional / InterfaceModel S SP T MAX LB a Apac IT Y CacheManagement MajorHDAComponents SubsystemConfiguration Jumper Location / ConfigurationCylinderLimitationJumperDescription ModelsandCapacities ProductSpecificationsDriveConfiguration PerformanceSpecificationsAram E TE R Stan D ARD ME T RIC PhysicalDimensionsmaximumEnvironmentalLimits PowerRequirementsPowerModeDefinitions EPA Energy Star ComplianceReliabilitySpecifications Shock and VibrationParam E TE R OP ER AT ING ON- OPE R AT ING EMC/EMI SafetyRegulatoryComplianceHandlingandInstallation HardDriveHandlingPrecautionsElectro-StaticDischargeESD Multi-pack Shipping Container UnpackingandInspectionRepacking PhysicalInstallationHook up Before You BeginStart up Set upPIN IGN AL InterfaceConnectorATInterfaceDescription PinDescriptionSummaryPin Description Table PIN Name Signal Name Signal Desc RiptionPIO Timing IM in G Paramet ERS ModeDMATiming Imin G Paramet ERS ModeMode Ultra DMA TimingSustained Ultra DMA Data In Burst Device Terminating an Ultra DMA Data In Burst Initiating an Ultra DMA Data Out Burst Device Pausing an Ultra DMA Data Out Burst Device Terminating an Ultra DMA Data Out Burst HostSoftwareInterface Task File RegistersPOR T EAD WR ITE Conten TS LBA Bits CommandRegister M M a N D N a M E M M a N D code PA R a M E T E R S U S E D SummaryControl Diagnostic Registers Reset and Interrupt Handling InterfaceCommands ReadCommands Read DMA WriteCommands Write Multiple ModeSet/CheckCommands VAL UE DES C RIP TionLE VE L VAL UE Omman D Timer VAL UE TIME-OUT Period PowerModeCommandsSleep Mode Or D ENT Desc Ription InitializationCommandsOr D 15- 10, as c urrently defined Initialize Drive Parameters ER ROR Code Desc Ription Seek,FormatandDiagnosticCommandsKey Register A.R.T. CommandSetSupport ServiceandSupportServicePolicy NoQuibbleServiceFrom Dial Glossary AccesstimeCorrectableerror Fetch Landingzoneorlzone Physicalsector Softerror