Maxtor 5120 manual System Hangs During Boot

Page 32

INSTALLATION

9 System Hangs During Boot

If the system hangs during the boot process after installing the Maxtor hard drive – either before or after setting the system BIOS – the system many have a BIOS with a cylinder limitation. This may occur for hard drives that exceed 2.1 GB. If this happens,

do the following:

1Turn the system OFF.

2Install the cylinder limitation jumper (J46) on the drive. The figure below shows the Maxtor hard drive configured as a Master or Slave device with the cylinder limitation jumper installed.

IMPORTANT: When the Cylinder Limitation jumper (J46) is installed, the Maxtor hard drive must be prepared using MaxBlast installation software.

3If the BIOS was set to AUTO DETECT, follow the instructions in Section 7 to prepare the hard drive using the MaxBlast installation software.

If other BIOS settings were used, access the system BIOS SETUP program and set the parameters to aUserDefinableTypewith 4,092 cylinders, 16 heads and 63 sectorspertrackfortheMaxtorharddrive.ThenfollowtheinstructionsforsettingtheBIOSinSection7thenSection8topreparetheharddrivewithMaxBlastsoftware.

4 – 10

Image 32

Contents HA RD Drive Produc T MA Nual DiamondMax Plus 92048U8, 91792U7, 91536U6, 91280U5, 91024U4 and 90750U3Revisions Manual No Before You Begin U T I O NContents Product Specifications Handling and InstallationAT Interface Description Host Software InterfaceGlossary Interface CommandsService and Support Figures Introduction Maxtor CorporationManual Organization AbbreviationsSignal Conventions ConventionsKey Words NumberingDiamondMax Plus 5120 Key Features Product DescriptionProduct Features Functional / InterfaceOn-the-Fly Hardware Error Correction Code ECC Logical Block AddressingDefect Management Zone DMZ Software ECC CorrectionRead-Ahead Mode Cache ManagementBuffer Segmentation Automatic Write Reallocation AWRMajor HDA Components Subsystem Configuration Jumper Location/ConfigurationCylinder Limitation Dual Drive SupportProduct Specifications Drive ConfigurationPerformance Specifications Models and CapacitiesPhysical Dimensions Parameter Standard MetricPower Requirements Average Power Mode DefinitionsEPA Energy Star Compliance Environmental LimitsReliability Specifications Shock and VibrationCanadian Emissions Statement Safety Regulatory ComplianceRadiated Electromagnetic Field Emissions EMC Compliance Handling and Installation Hard Drive Handling PrecautionsPre-formatted Drive Important NoticeUnpacking and Inspection Multi-pack Shipping ContainerRepacking Physical InstallationRecommended Mounting Configuration Handling Precautions Tools for InstallationSystem Requirements Drive Identification InformationGeneral Requirements Hard Drive IdentificationSystems Using Cable Select Installing 5.25-inch Mounting Brackets and RailsInstalling in a Device Bay Mounting Drive in SystemAttaching Interface and Power Cables Attaching System CablesBios Cmos Parameters System SetupSetting the Bios Cmos Hard Drive Preparation System Hangs During Boot Pin Description Summary Interface ConnectorAT Interface Description PIN Name Signal Name Signal Description Pin Description TableTiming Parameters Mode PIO TimingDMA Timing Mode MIN MAX Ultra DMA TimingSustained Ultra DMA Data In Burst Device Terminating an Ultra DMA Data In Burst Initiating an Ultra DMA Data Out Burst Device Pausing an Ultra DMA Data Out Burst Device Terminating an Ultra DMA Data Out Burst Error Register Features RegisterHost Software Interface Task File RegistersSector Count Register Sector Number RegisterCylinder Number Registers Device/Head RegisterCommand Register Command Name Command Code Parameters Used SDH SummaryControl Diagnostic Registers Alternate Status RegisterDevice Control Register Digital Input RegisterInterrupt Handling Reset and Interrupt HandlingReset Handling Interface Commands Set Feature CommandsRead Verify Sectors Read CommandsRead Sectors Read DMA Read MultipleWrite Commands Set Multiple ModeWrite Sectors Write Verify SectorsWrite Multiple Write DMASet Feature Commands Set Features ModePower Mode Commands Sleep Mode Initialization Commands Identify Drive15-8 = PIO data transfer mode = Write Cache enabled Initialize Drive Parameters Format Track Seek, Format and Diagnostic CommandsExecute Drive Diagnostic A.R.T. Command Set Execute S.M.A.R.TService and Support Service PolicyNo Quibble Service SupportInternet MaxFax ServiceCustomer Service Access Time GlossaryCylinder Zero Gigabyte GB Logical Block Addressing Read Gate Signal THIN-FILM Media