Page 27 of 32 |
Appendix D. Driver Error Messages
The driver reports information and errors to you in the form of messages printed to the error log. Those messages marked with a * are only printed once even if they occur repeatedly.
| Error Message |
|
|
|
| Explanation |
|
| |||
|
|
|
|
|
|
|
|
| The length of the Map Descriptor used to expose driver statistics is too | ||
| CarrierDP:1 |
| FYI. |
| The |
| short. Set the length to at least 1000 by editing the CSV file. Then reset | ||||
| MapDesc called <%s> is too |
| the FieldServer. You can ignore this message if you wish – the driver will | ||||||||
| short |
|
|
|
|
|
|
| abandon statistics which require the length of the Map Descriptor to be | ||
|
|
|
|
|
|
|
|
| increased. |
|
|
| CarrierDP:2 FYI. You could |
|
|
|
| ||||||
| have | used | a | MapDesc |
| You can safely ignore this message. It is a prompt. Read Appendix D.1 of | |||||
| called | <%s> | to |
| expose |
| this manual for more information. |
| |||
| diagnostic info. |
|
|
|
|
|
|
| |||
| CarrierDP:3 |
| Err. |
| Illegal |
| Valid node numbers are in the range 1 to 15 inclusive. Read section 4.3 | ||||
| Node_ID=%d Valid=1..15 |
| for more information.* |
|
| ||||||
| CarrierDP:4 | FYI. | Address |
| You can safely ignore this message. The address parameter is | ||||||
| has no meaning. Best set to |
| commonly used in FieldServer configurations but it has no meaning in | ||||||||
|
| the configuration of this driver. It is best to remove the parameter from | |||||||||
| 0 MapDesc=<%s> |
|
|
|
| the configuration or set its value to 0.* |
| ||||
| CarrDP:#5 | Err. DataPort is |
| The Carrier DataPort device is | read only. You cannot | have a Map | |||||
| read | only. | No |
| wrbc/x. |
| Descriptor which writes to the | device. Delete the Map | Descriptor or | ||
| MapDesc=<%s> |
|
|
|
| changing it to a read* |
|
| |||
| CarrDP:#6 | Err. Fieldname |
|
|
|
| |||||
| max | length |
|
| =8. |
|
|
|
| ||
| MapDesc=<%s> |
|
|
|
| You can use no more than 8 characters to define a field name and no | |||||
|
|
|
|
|
|
|
|
| |||
| CarrDP:#7 Err. Field | Desc. |
| more than 24 to define the field description.* |
| ||||||
| max | length |
|
| =%d. |
|
|
|
| ||
| MapDesc=<%s> |
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
| |||
| CarrierDP:8 |
| Err. |
|
| Length |
| The length parameter must be set in the configuration file and it must be | |||
| required. MapDesc=<%s> |
| set to a value greater than zero. Appendix A.3 provides additional | ||||||||
|
| information.* |
|
| |||||||
| CarrierDP:9 | FYI. Duplicate |
| You have specified a discrete state word in the configuration file which | |||||||
|
| duplicates one already in the list. The driver uses the new value specified | |||||||||
| state=<%s>. | Value | has |
| in the CSV file to replace the previous value. Thus it is possible to | ||||||
| been | updated | from=%d |
| change the values for the driver’s default discrete state words. You can | ||||||
| to=%d |
|
|
|
|
|
|
| safely ignore this message; it is for your information only. |
| |
|
|
|
|
|
|
|
|
|
| ||
| CarrierDP:10 Err. No space. |
| The driver has limited space to store discrete state keywords added in | ||||||||
|
| the configuration file. The maximum is 150 words including the driver’s | |||||||||
| Driver | rejects |
|
| value |
| defaults. Remove some of the keywords you have added to the | ||||
| state=<%s> value=%d |
| configuration file* |
|
| ||||||
| CarrierDP:11 | FYI. |
| User |
| You can safely ignore this message; it is for your information only. Each | |||||
| added | value | state=<%s> |
| time a new discrete state word is added to the driver from the | ||||||
| value=%d |
|
|
|
|
|
| configuration file, the driver reports the new word and its value. | |||
| CarrierDP:12 | Err. |
| Length |
| The driver reports that the read table command resulted in more | |||||
| too short to store all. |
| variables being returned than you have reserved space for (with the | ||||||||
| MD=<%s> |
|
|
|
|
|
| length parameter). Increase the length parameter. * |
| ||
*Correct the error by editing the configuration CSV file, downloading the corrected file to the FieldServer and then resetting the FieldServer.
*Correct the error by editing the configuration CSV file, downloading the corrected file to the FieldServer and then resetting the FieldServer.
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web: www.fieldserver.com Tel: (408) 262 2299 Fax: (408) 262 2269 Toll Free: (888) 509 1970 email: support@fieldserver.com