| Page 30 of 32 |
| ||||
|
|
|
|
|
| |
| Error Message |
| Explanation |
|
| |
|
|
|
| There DataPort device responded but the response reports an error. The |
| |
|
|
|
| error number is printed in the message. The message also reports the |
| |
|
|
|
| name of the node that was polled. |
|
|
|
|
|
| The following 6 errors are documented. For other errors contact the |
| |
|
|
|
| Carrier Vendor. |
|
|
|
|
|
| #1 Invalid Command : The digit 1 returned as an error code means that |
| |
|
|
|
| the last ASCII character sent to the DATAPORT by the |
| |
|
|
|
| device is not one that the DATAPORT recognizes as a command. |
| |
|
|
|
| #2 No Display Table : The digit 2 returned as an error code means that |
| |
|
|
|
| the |
| |
|
|
|
| from a controller that is properly configured in the DATAPORT, but the |
| |
|
|
|
| controller does not contain a point display table. |
|
|
|
|
|
| #3 CCN Bus Communication Error: The digit 3 returned as an error code |
| |
|
|
|
| means that the DATAPORT cannot transmit data from the requested |
| |
| CarrDP:#33 | Err. | DataPort | controller because a communication error occurred while the |
| |
| DATAPORT was acquiring data from that controller. |
|
| |||
| responded | with | Err=%d. |
|
|
|
| Device=%s |
|
| #4 Database Full : The digit 4 returned as an error code means that the |
| |
|
|
|
|
| ||
|
|
|
|
| ||
|
|
|
| from a controller that is properly configured in the DATAPORT, but the |
| |
|
|
|
| controller is beyond the 900 point limit. For example, if controllers 1 |
| |
|
|
|
| through 10 each contain 90 points, a command for the DATAPORT to |
| |
|
|
|
| transmit data from controller 11, 12, 13, 14, or 15 will result in error code |
| |
|
|
|
| 4. |
|
|
|
|
|
| #5 DATAPORT Busy : The digit 5 returned as an error code means that |
| |
|
|
|
| a static data update is in progress, preventing the DATAPORT from |
| |
|
|
|
| responding successfully to a Send Controller Data Command or a Send |
| |
|
|
|
| Data Periodically command. |
|
|
|
|
|
| #6 Controller Not Configured : The digit 6 returned as an error code |
| |
|
|
|
| means that the |
| |
|
|
|
| transmit data from a controller that is not configured in the DATAPORT. |
| |
|
|
|
| For example, if only controllers 1 through 5 are configured in the |
| |
|
|
|
| DATAPORT, a command of 0 (Send Controller Data for Controller 15) |
| |
|
|
|
| will result in error code 6. |
|
|
|
|
|
| |||
| CarrDP:#99 Err. Cant open | This message should only be printed in simulation mode (QA testing). If |
| |||
| INI file for response. | you see this message call Tech Support. |
|
| ||
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web: www.fieldserver.com Tel: (408) 262 2299 Fax: (408) 262 2269 Toll Free: (888) 509 1970 email: support@fieldserver.com