Intermec F4 manual Cleaning the Media Guides

Page 55

Chapter 10 Maintenance

Cleaning the Media Guides

Both parts of the label stop sensor, which controls the paper feed, are covered by transparent plastic guides. The guides have areas, through which the light between the two parts of the label stop sensor is transmitted. These areas (indicated by a shade of gray in illustration #2 below) must be kept clean from dust, stuck labels, and adhesive residue.

If the printer starts to feed out labels in an unexpected way, raise the upper guide–as described below–and check for any object that may block the beam of light (dust, stuck labels, adhesive residue, etc.). If necessary, clean the guides using a cleaning card or a soft cloth soaked with isopropyl alcohol. Do not use any other chemicals. Be careful not to scratch the guides.

Warning!

Isopropyl alcohol [(CH3)2CHOH; CAS 67-63-0] is a highly flammable, moderately toxic, and mildly irritating substance.

1

2

Lift the inner part of the upper guide and

pull it outwards,disengaging it from the lower

guide. Take care not to damage the cable.

Tilt the upper guide upwards and clean the areas marked with grey. After cleaning, reas- semble in reverse order.

54

Intermec EasyCoder F4 – Installation & Operation IPL Version, Ed. 3

Page 54 Page 56
Image 55
Page 54 Page 56
Contents EasyCoder F4 Bar Code Label Printer Contents Contents, Appendix GS Notice Germany FCC Notice United States of AmericaDOC Notice Canada Canadian Dept. of Communication Ministère des Communications du CanadaEasyCoder F4 Declaration of Conformity89/336/EEC and 73/23/EEC Description IntroductionChapter Voltage range. It also contains various signs of approval Safety PrecautionsUnpacking InstallationFront View Rear View Media Compartment Media Compart- ment, Media Supply Positions Omitted in dedicated direct thermal printing models Print MechanismConnections Power ComputerControl Lamps Display Controls and IndicatorsBeeper KeyboardStarting Up Switching OnTear-Off Media LoadTear-Off, Media is guided with a minimum of play Pull downwards Tear-Off with Quick-Load Tear-Off with Quick-Load, Self-strip Peel-OffPeel-Off, Insert the start of the liner under the lip Peel-Off, Quality or cause unnecessary wear to the printhead External SupplyStraight-through printing-preferably with Quick-Load There is no need to remove the media supply roll postRibbon Load Thermal Transfer PrintingRibbon Load, Setting Up the Printer Ribbon Load, Communication Setting Up the PrinterDescription Default Setup Test/ServiceParity Serial CommunicationBaud Rate Data BitsPrinting Setup Parameters,Serial Communication, Protocol Printhead hot Label at strip pin Label skippingReady Serial Communication, Protocol,Testprint Test/ServiceTest/Service, Label Length MediaMedia Type Paper TypeMedia, Darkest. Default value is 0%Darkness Entering Setup Mode At Installation Setup ModeNavigating in Setup Mode Setup Mode Overview, Part From previous Press Setup to exit the Setup Mode Introduction OptionsIntegral Liner Takeup Unit DTP ModelInch Adapter Quick-Load Guides Label Taken Sensor Interface Boards Symptom Possible Cause Remedy Refer to TroubleshootingPrinthead Cleaning MaintenanceRemove any media and transfer ribbon Printhead Cleaning,Printhead Cleaning, External Cleaning Cleaning the Media Guides Printhead Replacement Printhead Replacement, Printhead Replacement, Narrow Media Adjustment AdjustmentsFive clicks out 20 mm Two clicks outThree clicks out 12 mm Four clicks out 16 mmPrinthead Pressure Ribbon Break Shaft Technical Data Data Interfaces Accessories and OptionsSensors ControlsTTR High Gloss Polyester Media SpecificationsDirect Thermal Media TTR Premium BoardCore Media Roll SizeRoll Non-Adhesive Strip MediaMinimum 23.8 mm Media,Self-Adhesive Strip ⇒ Media Width including liner Maximum 114.3 mmInches 12 mm 16 mm 20 mm Self-Adhesive LabelsMaximum Depends on Dram size Minimum Inches Following distances from the inner edge of the mediaFive fixed positions distance from inner edge of the media Tickets with GapMin. length between slots Max. length between slots Depends on Dram sizeMark Tickets with Black MarkMaximum Depends on Dram size Minimum 20.0 mm Inches Common 12.5 mm Inches MinimumTransfer Ribbons Sensitivity Number Media or Ribbon Setting the Media Sensitivity Number,Type the following command lines and press Enter Where SIg1,567 sets the media sensitivity number toSetting Direct Thermal Media Setting the Media Sensitivity Number,Direct Thermal Media Sensitivity Settings Thermal Transfer Media and Ribbon Sensitivity SettingsInterfaces Default Communication SetupRS-232 Interface Board Interface Cable ConnectorsPin Signal Name IeeeEasyLAN 100i Interface Board Supported IPL-3 Commands Supported IPL-3 Commands, Supported IPL-3 Commands, ESCu SIF

F4 specifications

The Intermec F4 is a robust and versatile mobile computer designed to meet the rigorous demands of various industries, including retail, warehouse management, and field service. This device stands out for its impressive combination of durability, performance, and user-friendly features.

One of the main features of the Intermec F4 is its high-performance barcode scanning capability. Equipped with a 1D and 2D barcode scanner, the F4 enables quick and accurate data capture, allowing users to efficiently handle inventory management, order fulfillment, and asset tracking. This capability is essential in environments where accuracy and speed are paramount.

In addition to its scanning features, the Intermec F4 showcases advanced wireless connectivity options. With support for Wi-Fi, Bluetooth, and GSM/GPRS communication, users can stay connected to their networks and devices, ensuring seamless data transmission on the go. This connectivity is crucial for real-time information access and collaboration among team members in the field or warehouse.

The F4 is built with a rugged design that complies with IP54 and MIL-STD-810G standards, which means it can withstand harsh conditions, including dust, moisture, and accidental drops. This durability ensures that the device can operate effectively in demanding environments, reducing the risk of downtime due to equipment failure.

Another notable characteristic of the Intermec F4 is its large, high-resolution touchscreen display. The device features a 4-inch display that is both sunlight-readable and capable of responding to touch even when users are wearing gloves. This ergonomic design enhances the user experience, making it easier for employees to navigate applications and access vital information promptly.

Battery life is also a significant consideration with the Intermec F4. The device comes with an interchangeable battery that supports extended operation, allowing users to work longer without the need for frequent recharging. This feature is especially beneficial in field operations where access to power sources may be limited.

In conclusion, the Intermec F4 is a powerful mobile computing solution that combines advanced scanning technology, wireless connectivity, and rugged durability. Its user-friendly design and efficient performance make it an ideal choice for various applications in logistics, retail, and field services, offering businesses a reliable tool to enhance productivity and streamline operations. By investing in the Intermec F4, organizations can facilitate better inventory management, improve workflow efficiency, and ensure a higher level of accuracy in their processes.
Top Page Image Contents