Intermec F4 manual Printhead Pressure

Page 61

Chapter 11 Adjustments

Printhead Pressure

The pressure of the thermal printhead against the ribbon or media is factory-adjusted. However, the use of thicker or thinner media than normal could require the printhead pressure to be readjusted.

Using a straight-slot screwdriver, turn the adjustment screw clockwise for more pressure (+) or counterclockwise for less pressure (-). Print a few labels and check the printout. Increased pressure generally gives a darker printout and vice versa. Repeat until the desired result is obtained.

To return to the factory setting, tighten the screw (+) as far as it goes and then loosen it (-) six full turns.

Caution!

Do not use a higher printhead pressure than necessary because it may increase the wear of the printhead and shorten its life.

Adjustment Screw

60

Intermec EasyCoder F4 – Installation & Operation IPL Version, Ed. 3

Page 60 Page 62
Image 61
Page 60 Page 62
Contents EasyCoder F4 Bar Code Label Printer Contents Contents, Appendix DOC Notice Canada Canadian Dept. of Communication FCC Notice United States of AmericaMinistère des Communications du Canada GS Notice GermanyEasyCoder F4 Declaration of Conformity89/336/EEC and 73/23/EEC Description IntroductionChapter Voltage range. It also contains various signs of approval Safety PrecautionsUnpacking InstallationFront View Rear View Media Compartment Media Compart- ment, Media Supply Positions Omitted in dedicated direct thermal printing models Print MechanismConnections Power ComputerControl Lamps Display Controls and IndicatorsBeeper KeyboardStarting Up Switching OnTear-Off Media LoadTear-Off, Media is guided with a minimum of play Pull downwards Tear-Off with Quick-Load Tear-Off with Quick-Load, Self-strip Peel-OffPeel-Off, Insert the start of the liner under the lip Peel-Off, Straight-through printing-preferably with Quick-Load External SupplyThere is no need to remove the media supply roll post Quality or cause unnecessary wear to the printheadRibbon Load Thermal Transfer PrintingRibbon Load, Setting Up the Printer Ribbon Load, Description Default Setup Setting Up the PrinterTest/Service CommunicationBaud Rate Serial CommunicationData Bits ParitySerial Communication, Protocol Setup Parameters,Printhead hot Label at strip pin Label skipping PrintingReady Serial Communication, Protocol,Testprint Test/ServiceTest/Service, Media Type MediaPaper Type Label LengthMedia, Darkest. Default value is 0%Darkness Entering Setup Mode At Installation Setup ModeNavigating in Setup Mode Setup Mode Overview, Part From previous Press Setup to exit the Setup Mode Introduction OptionsIntegral Liner Takeup Unit DTP ModelInch Adapter Quick-Load Guides Label Taken Sensor Interface Boards Symptom Possible Cause Remedy Refer to TroubleshootingPrinthead Cleaning MaintenanceRemove any media and transfer ribbon Printhead Cleaning,Printhead Cleaning, External Cleaning Cleaning the Media Guides Printhead Replacement Printhead Replacement, Printhead Replacement, Narrow Media Adjustment AdjustmentsThree clicks out 12 mm Two clicks outFour clicks out 16 mm Five clicks out 20 mmPrinthead Pressure Ribbon Break Shaft Technical Data Sensors Accessories and OptionsControls Data InterfacesDirect Thermal Media Media SpecificationsTTR Premium Board TTR High Gloss PolyesterCore Media Roll SizeRoll Non-Adhesive Strip MediaSelf-Adhesive Strip Media,⇒ Media Width including liner Maximum 114.3 mm Minimum 23.8 mmMaximum Depends on Dram size Minimum Inches Self-Adhesive LabelsFollowing distances from the inner edge of the media Inches 12 mm 16 mm 20 mmMin. length between slots Tickets with GapMax. length between slots Depends on Dram size Five fixed positions distance from inner edge of the mediaMaximum Depends on Dram size Minimum 20.0 mm Inches Tickets with Black MarkCommon 12.5 mm Inches Minimum MarkTransfer Ribbons Sensitivity Number Type the following command lines and press Enter Setting the Media Sensitivity Number,Where SIg1,567 sets the media sensitivity number to Media or RibbonDirect Thermal Media Sensitivity Settings Setting the Media Sensitivity Number,Thermal Transfer Media and Ribbon Sensitivity Settings Setting Direct Thermal MediaInterfaces Default Communication SetupRS-232 Interface Pin Signal Name Interface Cable ConnectorsIeee BoardEasyLAN 100i Interface Board Supported IPL-3 Commands Supported IPL-3 Commands, Supported IPL-3 Commands, ESCu SIF

F4 specifications

The Intermec F4 is a robust and versatile mobile computer designed to meet the rigorous demands of various industries, including retail, warehouse management, and field service. This device stands out for its impressive combination of durability, performance, and user-friendly features.

One of the main features of the Intermec F4 is its high-performance barcode scanning capability. Equipped with a 1D and 2D barcode scanner, the F4 enables quick and accurate data capture, allowing users to efficiently handle inventory management, order fulfillment, and asset tracking. This capability is essential in environments where accuracy and speed are paramount.

In addition to its scanning features, the Intermec F4 showcases advanced wireless connectivity options. With support for Wi-Fi, Bluetooth, and GSM/GPRS communication, users can stay connected to their networks and devices, ensuring seamless data transmission on the go. This connectivity is crucial for real-time information access and collaboration among team members in the field or warehouse.

The F4 is built with a rugged design that complies with IP54 and MIL-STD-810G standards, which means it can withstand harsh conditions, including dust, moisture, and accidental drops. This durability ensures that the device can operate effectively in demanding environments, reducing the risk of downtime due to equipment failure.

Another notable characteristic of the Intermec F4 is its large, high-resolution touchscreen display. The device features a 4-inch display that is both sunlight-readable and capable of responding to touch even when users are wearing gloves. This ergonomic design enhances the user experience, making it easier for employees to navigate applications and access vital information promptly.

Battery life is also a significant consideration with the Intermec F4. The device comes with an interchangeable battery that supports extended operation, allowing users to work longer without the need for frequent recharging. This feature is especially beneficial in field operations where access to power sources may be limited.

In conclusion, the Intermec F4 is a powerful mobile computing solution that combines advanced scanning technology, wireless connectivity, and rugged durability. Its user-friendly design and efficient performance make it an ideal choice for various applications in logistics, retail, and field services, offering businesses a reliable tool to enhance productivity and streamline operations. By investing in the Intermec F4, organizations can facilitate better inventory management, improve workflow efficiency, and ensure a higher level of accuracy in their processes.
Top Page Image Contents