Intermec F4 manual Media Roll Size, Core

Page 66

Appendix 2 Media Specifi cations

Media Roll Size

Core

 

Diameters:

38-40 mm (1.5 inches) or 76.2 mm (3 inches)

Width:

Must not protrude outside the media

The media must be wound up on the core in such a way that the printer can pull the end free.

Roll

 

 

Max. diameter:

 

 

- Position 1

152 mm

(6.00 inches)

- Position 2

213 mm

(8.38 inches)

- Position 3

213 mm

(8.38 inches)

Max. width:

114.3 mm

(4.50 inches)

Min. width (standard):

25 mm

(1.00 inches)

Min. width (Quick-Load):

40/80 mm

(1.57/3.15 inches)

Max. media thickness:

175 µm

(0.007 inches)

The maximum recommended media thickness is 175µm. A thicker media may be used, but print quality will be reduced. The stiffness is also important and must be balanced against thickness to maintain print quality.

Media rolls to be loaded inside the printer should be wound with the printable side facing outwards.

The media supply must not be exposed to dust, sand, grit, etc. Any hard particles, however small, can damage the printhead.

Intermec EasyCoder F4 – Installation & Operation IPL Version, Ed. 3

65

Page 65 Page 67
Image 66
Page 65 Page 67
Contents EasyCoder F4 Bar Code Label Printer Contents Contents, Appendix Ministère des Communications du Canada FCC Notice United States of AmericaDOC Notice Canada Canadian Dept. of Communication GS Notice GermanyDeclaration of Conformity EasyCoder F489/336/EEC and 73/23/EEC Introduction DescriptionChapter Safety Precautions Voltage range. It also contains various signs of approvalInstallation UnpackingFront View Rear View Media Compartment Media Compart- ment, Media Supply Positions Print Mechanism Omitted in dedicated direct thermal printing modelsPower Computer ConnectionsControls and Indicators Control Lamps DisplayKeyboard BeeperSwitching On Starting UpMedia Load Tear-OffTear-Off, Media is guided with a minimum of play Pull downwards Tear-Off with Quick-Load Tear-Off with Quick-Load, Peel-Off Self-stripPeel-Off, Insert the start of the liner under the lip Peel-Off, There is no need to remove the media supply roll post External SupplyStraight-through printing-preferably with Quick-Load Quality or cause unnecessary wear to the printheadThermal Transfer Printing Ribbon LoadRibbon Load, Setting Up the Printer Ribbon Load, Test/Service Setting Up the PrinterDescription Default Setup CommunicationData Bits Serial CommunicationBaud Rate ParityPrinthead hot Label at strip pin Label skipping Setup Parameters,Serial Communication, Protocol PrintingSerial Communication, Protocol, ReadyTest/Service TestprintTest/Service, Paper Type MediaMedia Type Label LengthDarkest. Default value is 0% Media,Darkness Setup Mode Entering Setup Mode At InstallationNavigating in Setup Mode Setup Mode Overview, Part From previous Press Setup to exit the Setup Mode Options IntroductionDTP Model Integral Liner Takeup UnitInch Adapter Quick-Load Guides Label Taken Sensor Interface Boards Troubleshooting Symptom Possible Cause Remedy Refer toMaintenance Printhead CleaningPrinthead Cleaning, Remove any media and transfer ribbonPrinthead Cleaning, External Cleaning Cleaning the Media Guides Printhead Replacement Printhead Replacement, Printhead Replacement, Adjustments Narrow Media AdjustmentFour clicks out 16 mm Two clicks outThree clicks out 12 mm Five clicks out 20 mmPrinthead Pressure Ribbon Break Shaft Technical Data Controls Accessories and OptionsSensors Data InterfacesTTR Premium Board Media SpecificationsDirect Thermal Media TTR High Gloss PolyesterMedia Roll Size CoreRoll Media Non-Adhesive Strip⇒ Media Width including liner Maximum 114.3 mm Media,Self-Adhesive Strip Minimum 23.8 mmFollowing distances from the inner edge of the media Self-Adhesive LabelsMaximum Depends on Dram size Minimum Inches Inches 12 mm 16 mm 20 mmMax. length between slots Depends on Dram size Tickets with GapMin. length between slots Five fixed positions distance from inner edge of the mediaCommon 12.5 mm Inches Minimum Tickets with Black MarkMaximum Depends on Dram size Minimum 20.0 mm Inches MarkTransfer Ribbons Sensitivity Number Where SIg1,567 sets the media sensitivity number to Setting the Media Sensitivity Number,Type the following command lines and press Enter Media or RibbonThermal Transfer Media and Ribbon Sensitivity Settings Setting the Media Sensitivity Number,Direct Thermal Media Sensitivity Settings Setting Direct Thermal MediaDefault Communication Setup InterfacesRS-232 Interface Ieee Interface Cable ConnectorsPin Signal Name BoardEasyLAN 100i Interface Board Supported IPL-3 Commands Supported IPL-3 Commands, Supported IPL-3 Commands, SIF ESCu

F4 specifications

The Intermec F4 is a robust and versatile mobile computer designed to meet the rigorous demands of various industries, including retail, warehouse management, and field service. This device stands out for its impressive combination of durability, performance, and user-friendly features.

One of the main features of the Intermec F4 is its high-performance barcode scanning capability. Equipped with a 1D and 2D barcode scanner, the F4 enables quick and accurate data capture, allowing users to efficiently handle inventory management, order fulfillment, and asset tracking. This capability is essential in environments where accuracy and speed are paramount.

In addition to its scanning features, the Intermec F4 showcases advanced wireless connectivity options. With support for Wi-Fi, Bluetooth, and GSM/GPRS communication, users can stay connected to their networks and devices, ensuring seamless data transmission on the go. This connectivity is crucial for real-time information access and collaboration among team members in the field or warehouse.

The F4 is built with a rugged design that complies with IP54 and MIL-STD-810G standards, which means it can withstand harsh conditions, including dust, moisture, and accidental drops. This durability ensures that the device can operate effectively in demanding environments, reducing the risk of downtime due to equipment failure.

Another notable characteristic of the Intermec F4 is its large, high-resolution touchscreen display. The device features a 4-inch display that is both sunlight-readable and capable of responding to touch even when users are wearing gloves. This ergonomic design enhances the user experience, making it easier for employees to navigate applications and access vital information promptly.

Battery life is also a significant consideration with the Intermec F4. The device comes with an interchangeable battery that supports extended operation, allowing users to work longer without the need for frequent recharging. This feature is especially beneficial in field operations where access to power sources may be limited.

In conclusion, the Intermec F4 is a powerful mobile computing solution that combines advanced scanning technology, wireless connectivity, and rugged durability. Its user-friendly design and efficient performance make it an ideal choice for various applications in logistics, retail, and field services, offering businesses a reliable tool to enhance productivity and streamline operations. By investing in the Intermec F4, organizations can facilitate better inventory management, improve workflow efficiency, and ensure a higher level of accuracy in their processes.
Top Page Image Contents