Intermec 6110 manual Acknowledgments

Page 2

" NOTICE	This publication contains information proprietary to Intermec Technologies Corpo-
	ration. It is being supplied to you with the express understanding that the informa-
	tion contained herein is for the benefit of the contracting party only, and may not
	be copied, distributed, or displayed to third parties without the express written
	consent of Intermec Technologies Corporation, and shall be returned to Intermec
	Technologies Corporation upon written request. If a purchase, license, or nondisclo-
	sure agreement has been executed, the terms of that agreement shall govern this
	document.
	This publication is furnished for information only, and the information in it is
	subject to change without notice. Although every effort has been made to provide
	complete and accurate information, Intermec Technologies Corporation assumes no
	responsibility or liability for any errors or inaccuracies that may appear in this
	document.
	Disclaimer of Warranties. The sample source code included in this document is
	presented for reference only. The code does not necessarily represent complete,
	tested programs. The code is provided “AS IS WITH ALL FAULTS.” ALL
	WARRANTIES ARE EXPRESSLY DISCLAIMED, INCLUDING THE
	IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
	PARTICULAR PURPOSE.
	We welcome your comments concerning this publication. Although every effort has
	been made to keep it free of errors, some may occur. When reporting a specific
	problem, please describe it briefly and include the book title and part number, as
	well as the paragraph or figure number and the page number.
	Send your comments to:
	Intermec Technologies Corporation
	Publications Department
	550 Second Street SE
	Cedar Rapids, IA 52401
	INTERMEC, NORAND, PENKEY, PENVIEW, ROUTE-COMMANDER, and
	BEVERAGE ROUTEBOOK are registered trademarks and NOR*WARE and
	RAPIDREP are trademarks of Intermec Technologies Corporation.

Ó1998 Intermec Technologies Corporation. All rights reserved.

Acknowledgments

Alexander is a registered trademark of Alexander Manufacturing Co. Ethernet is a trademark of Xerox Corporation.

Microclean II is a registered trademark of Foresight International.

Microsoft, MS, and MS-DOS, and Windows, are registered trademarks and Visual Basic for Windows, and Windows for Pen are trademarks of Microsoft Corporation.

SanDisk is a trademark of SanDisk Corporation

Image 2

Contents USER’S Guide Acknowledgments Contents Operation Figures Tables Section SectionAbout This User’s Guide Appendix B Hand-Held Computer DescriptionAppendix a Front View Back View Hand-Held Computer Keyboard Backlight BatteryDisplay Memory Main MemoryFlash ROM PC CardsPC Card Slots PC Card Slots Gold Shift Key Suspend and Resume KeySerial Ports Options and AccessoriesResetting Radio CardIntegrated Scanner Pod Port Replicator Slide the Port Replicator onto the computer as shownMagnetic Stripe Reader Serial Pod GSM with SIM card Hand-Held Computer Specifications Power sourceSystem Components Introduction Getting StartedRechargeable Battery Label Replace the battery with a similar kindInstalling the Main Battery Charging The Batteries Your Hand-Held ComputerPower Status LED External Source Multipack ChargerSingle Pack Charger Removing the Main Battery Measuring Battery Pack Capacity Backup Battery Backup Battery LifeBooting Using PC Cards to Load Your ProgramsInstalling PC Cards Bios UpdateAccessing the PC Card Slots Removing PC Cards Installing a Modem Card Installing Modem Cable Using the Magnetic Stripe Reader MSR Installing the Subscriber Identity Module SIM Remove the SIM cover from the hand-held computerInstalling SIM Routine Care and Maintenance Low Battery IndicationCase and Display Cleaning Your Hand-Held ComputerDocking Connectors Troubleshooting Troubleshooting Chart Are lightingCondition Solution Hand-Held Not Power Up Computer Does Repair Service Connector Pin-Outs Appendix aPin Docking Connector Pin Signal FunctionRJ-45 Phone Jack Pin-Outs Phone Jack Pin-OutsAppendix a Pop-Up Menus Appendix BEntry Point Drop-Down Lists Alphanumeric Fields Network ParametersTitle Screen Language Selection Communications Menu Communications Menu appears after the Title ScreenOption 1 Begin Comm Session Begin Comm Session with Network Hand-Held Computer User’s Guide B-9 Begin Comm Session with MODEM/DIRECT Begin Comm Session with Accessory Card Begin Comm Session with InterserverSession Status ESCHand-Held Computer User’s Guide B-13 Novell Netware 800 ESC key Appendix B Option 2 Comm Setting Suboption 1 Network Suboption 2 MODEM/DIRECT Suboption 3 Accessory Card Suboption 6 Interserver Suboption 4 Handheld Suboption 5 Remote OPSOption 3 Unit ID Option 4 Network ParametersNetwork Parameters with Nrinet or Tftp Suboption 1 Modem Type Option 4 Modem ParametersNetwork Parameters with Novell Netware Modem Init String Momentarily, the computer displays the modem’s response Suboption 2 Protocol Suboption 3 BPS RateSuboption 5 Auto Answer Option 5 Network InterfaceSuboption 4 Data Format Option 5 Phone Number Option 9 Advanced Utilities Suboption 1 SET DATE/TIME API AsyncBisync BInary SYNChronous communications Boot Default DriveBootable ATA ButtonController ClickCmos Complementary Metal Oxide Semiconductor CPUDOS Disk Operating System Default DriveDock Double-ClickEeprom EOTFlash Card ETX End Of TextFlash FSK Frequency Shift KeyingGUI/PM Host Controller Host AddressHost Computer Host Port com4980LAN Local Area Network InternetIrDA LayerLCD MS-DOS Microsoft Disk Operating System Native Mode ADKMQL Multi-Quad Lockbox NAK Negative AcknowledgementNull NmsdNrinet Pan Border Open Wireless LAN NodeOpen Systems PC Personal ComputerPEN*KEY Plug and Play PenRight Physical PortPixel Polled ProtocolProgrammer’s Reference Guide Portrait ModePort Replicator Proprietary SystemsRAS RXD TTY TXDUCS Uniform Communications Standard WirelessUCC Uniform Code Council UPC Universal Product CodeIndex Index