Intermec manual Bluetooth Communications, Module is installed in the PL4 printer

Page 30

Bluetooth Communications

Note: The following section only applies when the Bluetooth

Module is installed in the PL4 printer.

The radiated output power of this internal wireless radio is far below the FCC radio frequency exposure limits. Nevertheless, this Bluetooth radio must be used in such a manner that the antenna is 2.5 cm (1 inch) or further from the human body such as with a belt clip or shoulder strap. Do not use the printer in an unauthorized manner.

Attention: La puissance de sortie émise par ce module sans fil interne se situe bien au-dessous des limites d’exposition

àla radiofréquence stipulées par la FCC. Toutefois, ce module Bluetooth doit être utilisé de façon à ce que l’antenne se situe à 2,5 cm ou plus du corps humain, avec une pince de ceinture ou une courroie par exemple. Utiliser seulement l’imprimante de façon autorisée.

“Bluetooth” is a worldwide standard for the exchange of data between two devices via radio frequencies. Bluetooth radios are relatively low powered to help prevent interference with other devices running at similar radio frequencies. This low power limits the range of a Bluetooth device to about 10 meters (approximately 32 feet).

To exchange data, two Bluetooth enabled devices must establish a connection. Bluetooth software is always running in the background, ready to respond to connection requests. One device (known as the master or the client) must request a connection with another. The second device (the slave or the server) then accepts or rejects the connection. A Bluetooth enabled PL4 normally acts as a slave, but in theory any Bluetooth device can be either a master or a slave. This miniature network is sometimes referred to as a “piconet” and can consist of several Bluetooth enabled devices.

Each Bluetooth PL4 has a unique Bluetooth Device Address (BDA) loaded into its module when manufactured.

30	EasyCoder PL4 Printer User’s Guide

Image 30

Contents EasyCoder PL4 Printer Page Contents EasyCoder PL4 Printer User’s Guide Introducing the EasyCoder PL4 Printer Unpacking and InspectingReporting Damage Learning About the Printer Front view of the EasyCoder PL4Installing the Battery Charging the Battery Using the Single Battery ChargerTo use the single battery charger Using the 4-Pack Charger To charge the battery with the 4-pack chargerCharger LED Status Description Amber Green Battery Status Pack Charger Cycle Times for PL4 Batteries Percentage Charged TimeStandard Control Panel Functions Understanding the Control PanelsStandard Control Panel Button or LED FunctionLCD Control Panel LCD Control Panel Functions Status Icon FunctionsIcon Function Function Default Setting Options LCD FunctionsLoading the Media To load the mediaMedia supports Tear-Off mode To switch from Self-Strip mode to Tear-Off mode Loading Fanfold Media To load fanfold mediaVerifying the Printer Is Working To print a configuration label XxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxXXEC00-10-0042 802.11b section of report EasyCoder PL4 Printer User’s Guide Continuation of second report Parameter Default Setting Establishing Communications With a TerminalSerial Cable Communications Connecting the printer to a terminal Terminals and Cables Terminal Cable Part NumberBluetooth Communications Module is installed in the PL4 printerTo print labels from a Bluetooth-enabled device Processor Bluetooth Print UtilityWireless Local Area Network Wlan Communications Wlan Module Using a Compact Flash RadioWlan Module Using a Pcmcia Card Radio Setting Up LPD or TCP Printing To set up for LPD or TCP printing Setting Up WEP Encryption To test that the printer is ready for LPD or TCP printingTo set up WEP encryption To test the WEP setup Setting Up for POP3 E-mail Printing To set up for POP3 e-mail printing Where my password is the password for the POP3 accountTo test the POP3 e-mail printing Setting Up for Ad Hoc Mode To set up for Ad Hoc modeU1 Setvar wlan.operatingmode ad hoc Setting Up the Software To install Intermec PlusTo test the ad hoc connection Downloading Firmware To open Intermec PlusTo download firmware Using the Accessories Using the Belt Clip Using the Adjustable Shoulder Strap Extending Battery Life Maintaining the PrinterCleaning the Printer Cleaning the PL4 Printer Cleaning MethodCleaning Interval Troubleshooting Understanding the LEDs Understanding the Standard Control Panel LEDsUnderstanding the LCD Control Panel Icons Understanding the Status IconsSymptom Troubleshooting Printer ProblemsPrinter Problems SolutionSymptom Solution LPD TCP Using Communications Diagnostics Mode To enter Communications Diagnostics modeSpecifications Printing SpecificationsMemory/Communications Specifications Label Specifications Memory/Communications SpecificationsMinimum Black Mark Dimensions Font/Bar Code Specifications Physical/Environmental/Electrical SpecificationsPhysical/Environmental/Electrical Specifications Signal Pin # Name Type DescriptionCommunications Port Accessories EasyCoder PL4 Printer User’s Guide EasyCoder PL4 Printer User’s Guide 073204-001