EVGA 650I manual ‰ All, But Diskette, ‰ All, But Disk/Key, ‰ Extended Memory, ‰ Total Memory

Page 45

‰All, But Diskette

The system boot does not stop for a diskette error but will stop for all other errors.

‰All, But Disk/Key

The system boot does not stop for a keyboard or disk error, but will stop for all other errors.

Memory

These settings are display-only values that are determined by the BIOS POST

(Power-On Self Test).

 

 

Base Memory

640K

‰ Base Memory

Extended Memory

1047552K

BIOS POST determines the

Total Memory

1048576K

 

 

amount of base (or conventional) memory installed in the system.

‰Extended Memory

BIOS determines how much extended memory is present during the POST.

‰Total Memory

This value represents the total memory of the system.

34

Image 45
Contents Page User Guide Table of Contents Unpacking and Parts Descriptions Configuring the Bios Page Page Vii Parts not in the Kit Before You Begin…Intentions of the Kit Page Ultimate Overclocking FeaturesHigh-speed Memory Comprehensive Overclocking ToolsTrue x16 PCI Express Support Multiple Disk SetupDualDDR2 Memory Architecture Nvidia MediaShield StorageRAID Morphing Bootable Multidisk ArrayNetworking with Nvidia nForce Nvidia Native Gigabit EthernetUSB Motherboard Specifications Page Equipment UnpackingNvidia nForce 650i Ultra Motherboard Sata Signal Cable Qty FourNvidia nForce 650i Ultra Motherboard Layout Chassis Backpanel Connectors Safety Instructions Hardware InstallationPreparing the Motherboard Installing the CPUInstalling Memory DIMMs Installing the CPU FanInstalling the Motherboard Installing the I/O ShieldSecuring the Motherboard into the Chassis ¾ COM ‰ FDD ‰ IDE Connecting Cables Setting SwitchesPin ATX Power PWR1 Power ConnectionsPin ATX 12V Power PWR2 Connecting IDE Hard Disk DrivesConnecting Serial ATA Cables Front Panel Header Connecting Internal HeadersFront Panel Header Pins USB Headers USB 2.0 Header PinsAudio Front Audio ConnectorFan Connections FDD ConnectorPCI Slots Expansion SlotsClear Cmos Jumper Clrcmos Jumper SettingsPCI Express x1 Slots PCI Express x16 SlotConfiguring the Bios Main Menu Enter Bios Setup‰ Advanced Bios Features ‰ Standard Cmos Features‰ Advanced Chipset Features ‰ Power Management Setup‰ Set Password ‰ Load Defaults‰ Save & Exit Setup ‰ Exit Without SavingStandard Cmos Features Menu Standard Cmos Features MenuIDE Channel and Sata Channel Date and Time‰ Auto ‰ None‰ Manual ¾ Large‰ No Errors ‰ All ErrorsDrive a Halt On‰ All, But Diskette Memory‰ All, But Disk/Key ‰ Extended MemoryCdrom Advanced Bios FeaturesNetwork Boot Priority Hard Disk Boot PriorityRemovable Device Priority CPU Internal CacheFirst/Second/Third Boot Device Quick Power On Self TestBoot Other Device Boot Up NumLock StatusSecurity Option Apic ModeMPS Version Control For OS Full Screen Logo ShowAdvanced Chipset Features Advanced Chipset FeaturesCPU Spread Spectrum System ClocksFrequency Settings Spread Spectrum HT MultiplierFSB Memory Clock Mode Auto FSB & Memory Config¾ Linked ‰ FSB and Memory Clock Mode¾ Unlinked ‰ FSB QDR, MHz‰ Memory Timing Setting ‰ MEM DDR, MHz¾ Optimal ¾ Expert CPU Configuration ‰ Limit Cpuid MaxVal‰ CPU Thermal Control System Voltages ‰ Execute Disable Bit‰ C1E Enhanced Halt State ‰ Virtualization Technology‰ nForce SPP ‰ MemoryLoad Timing/Voltage Set Nvmem Memory TestSave Timing/Voltage Set System Bios CacheableHpet Function Nvidia GPU ExIntegrated Peripherals Menu Integrated Peripherals Menu‰ IDE DMA transfer access IDE Function Setup‰ Primary Master/Slave PIO ‰ Primary Master/Slave UdmaUSB Config RAID Config‰ RAID Enable ‰ Sata x Primary/SecondaryIDE HDD Block Mode MAC ConfigHD Audio Onboard FDC ControllerPower Management Setup Menu Acpi FunctionAcpi Suspend Type Power on Function Power On by Alarm‰ Password Soft-Off by PbntPnP/PCI Configuration Menu ‰ Hot Key Power On‰ Mouse Left Reset Configuration Data Init Display FirstResources Controlled By IRQ Resources PCI/VGA Palette SnoopMaximum Payload Size System Monitor Menu System Monitor MenuPress Enter to display the Dynamic Fan Control menu Dynamic Fan ControlHardware Installation