EVGA 650I manual Connecting Internal Headers, Front Panel Header

Page 30

Hardware Installation

Connecting Internal Headers

Front Panel Header

The front panel header on this motherboard is one connector used to connect the following four cables:

‰PWRLED

Attach the front panel power LED cable to these two pins of the connector.

The Power LED indicates the system’s status. When the system is in S0 status, the LED is on. When the system is in S1, S3, S4, S5 status, the LED is off.

No HD_LED

Connect RESET - +

9 1

10 2 1

Blank PWRSW - +

PWRLED

Note: The power LED cable in some chassis is a three pin connector with the pins installed in positions 1 and 3. If your chassis has a three pin connector, you will need to remove pin 3 and put it into position 2 or you can use a pair of scissors to cut out position 2. Most chassis come with a two pin connector.

‰PWRSW

Attach the power button cable from the case to these two pins. Pressing the power button on the front panel turns the system on off rather than using the power supply button.

‰HD_LED

Attach the hard disk drive indicator LED cable to these two pins. The HDD indicator LED indicates the activity status of the hard disks.

‰RESET

Attach the Reset switch cable from the front panel of the case to these two pins. The system restarts when the RESET switch is pressed.

19

Image 30
Contents Page User Guide Table of Contents Unpacking and Parts Descriptions Configuring the Bios Page Page Vii Before You Begin… Parts not in the KitIntentions of the Kit Page High-speed Memory FeaturesUltimate Overclocking Comprehensive Overclocking ToolsDualDDR2 Memory Architecture Multiple Disk SetupTrue x16 PCI Express Support Nvidia MediaShield StorageNetworking with Nvidia nForce Bootable Multidisk ArrayRAID Morphing Nvidia Native Gigabit EthernetUSB Motherboard Specifications Page Unpacking EquipmentSata Signal Cable Qty Four Nvidia nForce 650i Ultra MotherboardNvidia nForce 650i Ultra Motherboard Layout Chassis Backpanel Connectors Hardware Installation Safety InstructionsInstalling the CPU Preparing the MotherboardInstalling the CPU Fan Installing Memory DIMMsInstalling the Motherboard Installing the I/O ShieldSecuring the Motherboard into the Chassis Connecting Cables Setting Switches ¾ COM ‰ FDD ‰ IDEPower Connections Pin ATX Power PWR1Connecting IDE Hard Disk Drives Pin ATX 12V Power PWR2Connecting Serial ATA Cables Connecting Internal Headers Front Panel HeaderFront Panel Header Pins USB 2.0 Header Pins USB HeadersFront Audio Connector AudioFDD Connector Fan ConnectionsExpansion Slots PCI SlotsPCI Express x1 Slots Jumper SettingsClear Cmos Jumper Clrcmos PCI Express x16 SlotConfiguring the Bios Enter Bios Setup Main Menu‰ Advanced Chipset Features ‰ Standard Cmos Features‰ Advanced Bios Features ‰ Power Management Setup‰ Save & Exit Setup ‰ Load Defaults‰ Set Password ‰ Exit Without SavingStandard Cmos Features Menu Standard Cmos Features MenuDate and Time IDE Channel and Sata Channel‰ Manual ‰ None‰ Auto ¾ LargeDrive a ‰ All Errors‰ No Errors Halt On‰ All, But Disk/Key Memory‰ All, But Diskette ‰ Extended MemoryAdvanced Bios Features CdromRemovable Device Priority Hard Disk Boot PriorityNetwork Boot Priority CPU Internal CacheBoot Other Device Quick Power On Self TestFirst/Second/Third Boot Device Boot Up NumLock StatusMPS Version Control For OS Apic ModeSecurity Option Full Screen Logo ShowAdvanced Chipset Features Advanced Chipset FeaturesSystem Clocks CPU Spread SpectrumFrequency Settings HT Multiplier Spread SpectrumFSB & Memory Config FSB Memory Clock Mode Auto¾ Unlinked ‰ FSB and Memory Clock Mode¾ Linked ‰ FSB QDR, MHz‰ Memory Timing Setting ‰ MEM DDR, MHz¾ Optimal ¾ Expert CPU Configuration ‰ Limit Cpuid MaxVal‰ CPU Thermal Control ‰ C1E Enhanced Halt State ‰ Execute Disable BitSystem Voltages ‰ Virtualization Technology‰ Memory ‰ nForce SPPNvmem Memory Test Load Timing/Voltage SetHpet Function System Bios CacheableSave Timing/Voltage Set Nvidia GPU ExIntegrated Peripherals Menu Integrated Peripherals Menu‰ Primary Master/Slave PIO IDE Function Setup‰ IDE DMA transfer access ‰ Primary Master/Slave Udma‰ RAID Enable RAID ConfigUSB Config ‰ Sata x Primary/SecondaryHD Audio MAC ConfigIDE HDD Block Mode Onboard FDC ControllerPower Management Setup Menu Acpi FunctionAcpi Suspend Type ‰ Password Power On by AlarmPower on Function Soft-Off by PbntPnP/PCI Configuration Menu ‰ Hot Key Power On‰ Mouse Left Reset Configuration Data Init Display FirstResources Controlled By IRQ Resources PCI/VGA Palette SnoopMaximum Payload Size System Monitor Menu System Monitor MenuDynamic Fan Control Press Enter to display the Dynamic Fan Control menuHardware Installation