EPoX Computer specifications EP-3VWM Bios

Page 35

EP-3VWM

BIOS

 

 

 

 

Init Display First: If two video cards are used (1 AGP and 1 PCI) this specifies which one will be the primary display adapter. The default is PCI Slot.

PCI Slots: PCI video card will be primary adapter.

AGP: AGP video card will be primary adapter.

IDE HDD Block Mode: IDE Block Mode allows the controller to access blocks of sectors rather than a single sector at a time. The default is Enabled.

Enabled: Enabled IDE HDD Block Mode. Provides higher HDD transfer rates.

Disabled: Disable IDE HDD Block Mode.

Onboard FDD Controller: This controls the state of the onboard floppy controller. The default value is Enabled.

Enabled: Enable the Onboard VIA686A Chips’s floppy drive interface controller.

Disabled: Disable the Onboard VIA686A Chip’s floppy drive interface controller.

Onboard Serial Port 1: This field allows the user to configure the 1st serial port. The default is Auto.

AUTO: Enable Onboard Serial port 1 and address is Auto adjusted.

COM1: Enable Onboard Serial port 1 and address is 3F8H/IRQ4.

COM2: Enable Onboard Serial port 1 and address is 2F8H/IRQ3.

COM3: Enable Onboard Serial port 1 and address is 3E8H/IRQ4.

COM4: Enable Onboard Serial port 1 and address is 2E8H/IRQ3.

Disabled: Disable Onboard SMC CHIP’s Serial port 1.

Onboard Serial Port 2: This field allows the user to configure the 2nd serial port. The default is Auto.

AUTO: Enable Onboard Serial port 2 and address is Auto adjusted.

COM1: Enable Onboard Serial port 2 and address is 3F8H/IRQ4.

COM2: Enable Onboard Serial port 2 and address is 2F8H/IRQ3.

COM3: Enable Onboard Serial port 2 and address is 3E8H/IRQ4.

COM4: Enable Onboard Serial port 2 and address is 2E8H/IRQ3.

Disabled: Disable Onboard SMC CHIP’s Serial port 2.

UART 2 Mode: This item allows you to determine which Infra Red (IR) function of onboard I/O chip.

The Choice: Standard, ASKIR, HPSIR.

Page 4-13

Image 35
Contents EP-3VWM User Notice Handling ProceduresContacting Technical Support Technical Support ServicesTable of Contents Appendix D Appendix Appendix aAppendix B Appendix CLeft Blank Introduction Components ChecklistEP-3VWM Form-Factor Summary of ATX chassis featuresPower-On/Off Remote Shield ConnectorSystem Block Diagram System Block DiagramEP-3VWM Features FeaturesFeatures Installation InstallationEP-3VWM Detailed Layout Section CPU Insertion Installation JP3 Section Jumper SettingsDimm Section System Memory Configuration Memory LayoutUnbuffered Dimm Module InstallationSection Device Connectors USB port header pin descriptions Power On/Off Main Menu Award Bios SetupStandard Cmos Setup Bios EP-3VWMBios Features Setup Advanced Bios FeaturesBios EP-3VWM EP-3VWM Bios Characters per second EP-3VWM Bios Advanced Chipset Features EP-3VWM Bios Bios EP-3VWM Integrated Peripherals Bios EP-3VWM EP-3VWM Bios Bios EP-3VWM Power Management Setup Bios EP-3VWM EP-3VWM Bios PNP/PCI Configuration EP-3VWM Bios PC Health Status Frequency/Voltage Control Defaults Menu Enter Password Supervisor/User Password SettingQuit without saving Y/N? Y Exit Selecting Save & Exit SetupSave to Cmos and Exit Y/N? Y Exit Without SavingAppendix Appendix aTimer & DMA Channels MAP RTC & Cmos RAM MAP Appendix Appendix B For Bios 6.0 CodeReset keyboard for Winbond 977 series Super I/O Checksum fails, use default value instead Appendix EP-3VWM CDROM… EP-3VWM Left Blank Appendix C Load Optimized DefaultsLeft Blank Ghost 5.1 Quick User’s Guide Appendix DAppendix EP-3VWM Appendix EP-3VWM Appendix EP-3VWM Appendix EP-3VWM