Energizer ER-PRO1400 Insert FileSaver software in CD-ROM drive on computer, Follow instructions

Installation

1	Insert FileSaver software in CD-ROM drive on computer
	and follow instructions.
3	Plug your modem or fax line into the UPS "OUT" line
	and your computer into the "IN" line. Plug the included
	USB cable from the UPS data port to the USB port
	on your computer.
	SITE WIRE FAULT
	DATA PORT
	CIRCUIT
	BREAKER AC INPUT
	Computer phone line
	to UPS IN plug
	FAX/MODEM
	UPS OUTPUT
	IN OUT
	IN
	NETWORK
	OUT
	Modem or fax line to
	UPS OUT plug

Use your battery backup sockets for: computer, monitor, and external storage devices (i.e. zip drive).

For surge protection, plug in: non-essential equipment such as printers, scanners, and speakers.

Do NOT use your UPS for: laser printers, vacuums, space heaters, copiers, or shredders.

4

2	Plug your Energizer® ER-PRO1400 UPS
	Power Protection system into a wall outlet.
	SITE WIRE FAULT
	DATA PORT
	CIRCUIT
	BREAKER AC INPUT
	FAX/MODEM
	UPS OUTPUT
	IN OUT

IN

NETWORK

OUT

Plug all equipment to the plugs in the back of the UPS

		SITE WIRE FAULT	computer, monitor,
DATA PORT			printer, speaker, other
	CIRCUIT	AC INPUT
	BREAKER
FAX/MODEM
		UPS OUTPUT
IN	OUT

IN

NETWORK

OUT

Trouble Shooting

Problem	Cause	Solution
UPS will not turn on; LED is not lit.	Your On/Off switch was not pushed in completely.	Press and hold the On/Off switch for 3 seconds,
		or until you hear a beeping sound.
	Your battery voltage is too low.	Call 1-866-337-6937 for help.
UPS system is remaining on battery mode.	Your power cord is loose.	Ensure that the cord is plugged in firmly.
	Your input fuse has been blown.	Remove some loads (devices) and replace fuse with similar rating.
	Your circuit breaker has been tripped.	Reset circuit breaker.
	Your line voltage is too high or too low.	Check your input voltage.
UPS is functioning normally, but the computer will not turn on.	Your computer input power cord is loose or disconnected.	Reconnect your computer input power cord.
Available backup time is less than the indicated rating.	Your battery is not fully charged or your battery is dead.	Recharge the battery for 6 hours and retest the backup time.
		If problem persists, call 1-866-337-6937 for help.
	Your UPS system is slightly overloaded.	Remove the least critical load (device).
The UPS system is continually beeping.	Your UPS system is overloaded.	Remove the non-critical loads (devices).
	Your UPS system has automatically defaulted to battery mode.	Remove non-critical loads (devices) and restart the UPS system.
The Site Wiring Fault LED is on.	Your polarity is reversed or another electrical issue.	Call an electrician to check and service your wiring.
Your communication function is not working.	You are using the wrong interface cable.	Ensure that you have the correct interface cable,
		or obtain one from your local retailer.

For any additional questions, or questions concerning the FileSaver software, please visit www.energizerups.com or call 1-877-267-4687.

Warranty

What does the warranty cover?

We warrant this product to be free from defects in material and workmanship during the warranty period. If a product proves to be defective in material or workmanship during the warranty period, we will, at our option, repair or replace the product with an equivalent model.

How long is the warranty effective?

Energizer® Power Protection products are warranted for 3 years for all parts and labor from the date of the first consumer purchase.

What does the warranty NOT cover?

1.Any product on which the serial number has been defaced, modified or removed.

2.Damage, deterioration or malfunction resulting from: accident, misuse, neglect, fire, water, lightening, or other acts of nature, unauthorized product modification, or failure to follow instructions supplied with the product.

3.Repair, or attempt to repair, by anyone who is not authorized.

4.Any damage of the product that occurred during shipping.

5.Installation of the product.

6.Any damage that results from the installation of the product.

7.Use of supplies or parts not meeting indicated specifications.

8.Normal wear and tear.

9.Any other cause which does not relate to a product defect.

Servicing and Replacing the Battery

Routine Maintenance:

Use dry soft cloths to clean the front panel and plastic parts. Do not use any detergent that contains any alcohol ingredient.

The expected lifetime of the internal battery is around three (3) years. Improper operation and/or exposure to a harsh environment will reduce the actual lifetime.

Charge the internal battery every three (3) months to recover the self-discharge capacity that is caused when the unit is in extended storage.

When replacing your battery, ensure that your new battery meets the required specifications.

Proper disposal of batteries is required. Refer to your local codes for disposal requirements.

Battery Replacement:

Lay the unit on its side. Use a screwdriver to open the battery cover on the bottom of the unit.

Grasp the tab attached to the battery and slide the battery out.

Storage Instructions:

Your unit should be stored in a cool, dry location.

Make sure that the internal battery is fully charged before storage. For extended storage in moderate climates, the battery should be charged for 12 hours every three (3) months by plugging the power cord into the wall outlet and turning on the main switch.

Repeat every two (2) months in high temperature locations.

How do you get service?

Call 1-866-337-6937 for help.

Can I use this product for life support?

We do not recommend the use of our products for life support equipment or direct care where failure of the product could cause failure or diminished effectiveness of the life support equipment or patient care.

Software installation:

1.Insert FileSaver CD into CD-ROM.

The software will execute automatically.

2.If the software can not perform properly, please press Start and execute the "D:\setup.exe"