Dell W-AP175, W- AP92, W-AP105, AP-92, AP-175, AP-93, W-AP93, AP-105 manual Physical Description

Page 14

2.4.1 Physical Description

The Aruba AP-175 Access Point is a multi-chip standalone cryptographic module consisting of hardware and software, all contained in a hard case. The module contains two 802.11 a/b/g/n transceivers, and 4 x N- type female interfaces (2 x 2.4 GHz, 2 x 5 GHz) for external antenna support (supports MIMO)

The hard case physically encloses the complete set of hardware and software components and represents the cryptographic boundary of the module.

The Access Point configuration tested during the cryptographic module testing included:

Aruba Part Number

Dell Corresponding Part Number

AP-175P-F1W-AP175P-F1

AP-175AC-F1W-AP175AC-F1

AP-175DC-F1W-AP175DC-F1

The exact firmware versions tested were:

∙ArubaOS_6xx_6.1.2.3-FIPS

∙Dell_PCW_6xx_6.1.2.3-FIPS

2.4.1.1Dimensions/Weight

The AP has the following physical dimensions:

∙260 mm x 240 mm x 105 mm (10.2" x 9.4" x4.1")

∙3.25 kg (7 lb)

2.4.1.2Interfaces

The module provides the following network interfaces:

∙1 x 10/100/1000 Base-T Ethernet (RJ45) Auto-sensing link speed and MDI/MDX

∙Antenna

o4 x N-Type female antenna interfaces

∙1 x RJ-45 console interface

The module provides the following power interfaces:

∙AP-175P: 48-volt DC 802.3at power over Ethernet (PoE+)

∙AP-175AC: 100-240 volt AC from external AC power source

∙AP-175DC: 12-48 volt DC from external DC power source

14

Image 14

Contents Version Feb Aruba Networks Crossman Ave Sunnyvale, CA Page AP-175 Series Aruba Dell Relationship Acronyms and AbbreviationsAP-105 Series Security Levels Physical SecurityROLES, Authentication and Services Acronyms and Abbreviations IntroductionAruba Dell Relationship GHz IPSecPhysical Description Product OverviewAP-92 Aruba Part Number Dell Corresponding Part NumberEnet AP-92 Indicator LEDs Label Function Action StatusPWR AP-93 Label Function Action StatusAP-93 Indicator LEDs Label Function Action Status AP-105 Wireless Access Point AP-105 SeriesAP-105 Indicator LEDs Label Function Action Status AP-175 Wireless Access Point AP-175 SeriesPhysical Description AP-175 Indicator LEDs Label Function Action Status PositionPhysical Security Module ObjectivesSecurity Levels Applying TELs2 AP-92 TEL Placement AP-92 Tel placement front viewAruba AP-92 Tel placement right view 3 AP-93 TEL Placement Aruba AP-92 Tel placement bottom viewAruba AP-93 Tel placement left view 4 AP-105 TEL Placement Aruba AP-93 Tel placement top viewAruba AP-105 Tel placement left view 5 AP-175 TEL Placement Aruba AP-105 Tel placement bottom viewAruba AP-175 Tel placement back view Inspection/Testing of Physical Security Mechanisms Aruba AP-175 Tel placement top viewConfiguring Remote AP Fips Mode Modes of OperationEnable Fips mode on the AP. This accomplished by going to Configuring Remote Mesh Portal Fips Mode Configuring Remote Mesh Point Fips Mode Verify that the module is in Fips mode Operational EnvironmentLogical Interfaces Fips 140-2 Logical Interfaces Module Physical InterfaceRoles Roles, Authentication and ServicesCrypto Officer Authentication Strength of Authentication Mechanisms User AuthenticationWireless Client Authentication Authentication Mechanism StrengthWPA2-PSK WPA2 PSK ServicesCrypto Officer Services KEKPTK User ServicesPMK Eapol MICWireless Client Services Unauthenticated Services∙ FTP ∙ Tftp ∙ NTP Cryptographic Algorithms Non-FIPS Approved AlgorithmsCritical Security Parameters HmacRNG PSK AES-CCMGMK GTKSelf Tests For an AES Atheros hardware Post failure