Dell F-Series manual Shut down Windows and turn off the server

Page 39

Click Cluster Disk, and then select the Driver tab. Change the startup set- ting for Cluster Disk from System to Disabled.

d.For Windows NT Server 4.0, Enterprise Edition, select the Services applet in the Control Panel. Change the start-up setting for Cluster Service from Automatic to Disabled.

For Windows 2000, select Start, point to Programs, point to Administra- tive Tools, and then point to Services. Change the start-up setting for Cluster Service from Automatic to Disabled.

e.Install Dell OpenManage Storage Consolidation software (StorageC) for a cluster environment. During the installation, check Yes in response to the question Will this server be used in a Microsoft Cluster Server environment?

f.Shutdown Windows and turn off the node.

3.Add the switches, if needed, and the additional servers to the SAN switch fabric.

4.Configure the hardware according to the Dell PowerEdge Cluster FE100/FL100 Installation and Troubleshooting Guide and the storage system according to the PowerVault storage system documentation.

5.Calculate the Execution Throttle value and change the Execution Throttle value in the NVRAM for each HBA. Ensure that the sum of all of these values does not exceed 250 and that each value does not exceed 90.

See the PowerVault system documentation for instructions for calculating and changing the Execution Throttle value.

6.Disconnect only the cables attached to the PowerVault 65xF storage system.

7.Perform the following steps on each additional server:

a.Install Windows NT Server 4.0, Enterprise Edition with Service Pack 6a or later, or Windows 2000 Advanced Server with the latest supported service pack. See the Dell PowerEdge Cluster FE100/FL100 Platform Guide for infor- mation on the supported service packs.

b.Install the QLogic driver.

c.Install the QLogic Fibre Channel configuration utility.

See “Installing the QLogic Fibre Channel Configuration Utility,” found earlier in this document, for information on installing QLConfig.

d.Install the Dell OpenManage ATF and reboot the server.

e.Install Dell OpenManage Storage Consolidation software (StorageC) for a cluster environment. During the installation, check Yes in response to the question Will this server be used in a Microsoft Cluster Server environment?

f.Shut down Windows and turn off the server.

support.dell.com

Dell PowerEdge Cluster F-Series SAN Guide 1-33

Image 39
Contents SAN Guide Page     Page Contents Figures Tables IndexDell PowerEdge Cluster Series SAN Guide SAN-Attached Cluster Direct-Attached ClusterPublic LAN Cluster ConsolidationCluster Consolidation Configuration PowerVault SAN ComponentsSAN-Attached Clusters SAN-Attached Cluster Rules and Guidelines Ter FE100/FL100 Platform Guide for more information Windows NT 4.0 Cluster Installation Overview Cluster Installation OverviewWindows 2000 Cluster Installation Overview Dell PowerEdge Cluster F-Series SAN Guide Using Dell PowerVault Fibre Channel Switches SAN-Attached Cluster ConfigurationsDell PowerEdge Cluster F-Series SAN Guide Configurations With Two to Four PowerVault DPEs Configurations With SAN Backup PowerVault Fibre SAN Connecting Multiple PowerEdge Clusters to a PowerVaultTwo PowerEdge Clusters Sharing a PowerVault SAN Zone Three PowerEdge Clusters Sharing a PowerVault SAN Dell PowerEdge Cluster F-Series SAN Guide Cluster Consolidation Configurations Cluster Consolidation Rules Cluster Consolidation Rules and GuidelinesBasic Installation Overview for Cluster Consolidation Dell PowerEdge Cluster F-Series SAN Guide Installing the QLogic Fibre Channel Configuration Utility DMI 2.0 Service Provider DMI 2.0 Client Cluster Consolidation Switch Zoning Requirements12. Example Showing Two Zones Example Configurations Dell PowerEdge Cluster F-Series SAN Guide Dell PowerEdge Cluster F-Series SAN Guide Dell PowerEdge Cluster F-Series SAN Guide Upgrading to a Cluster Consolidation Configuration Additional PowerEdge Cluster Maintenance ProceduresShut down Windows and turn off the server Dell PowerEdge Cluster F-Series SAN Guide Index Upgrading to a cluster consolidation configuration     EF # ,-./   $%  ~  Page                            Cavw  ab$WYN*†‡ˆ\ Y\¡b ¢  !#$% $           !#$%             &* #+     !12 345               =  ?@  ,ABCD      5  +E+FGCD HI!12JK+!=,LMNOPQRST R6UVWX      5 $           #  ! & -L-MQZf  ,-./VWnQ Áf–%   =HIYB-N              ! #  ! & -L-MQZf  ,-./VWnQ Áf–%   =HIYB-N !             7   ,L89B-N   WX \XGR WYN*ef†‡¡b ¢ CD!#$%          #                +`Ka%b             $% NOPQ•Ngž  2ãù4 0  y$  W   $% NOPQ•Ngž  2ãù4 0 ! $  WY %&WYN*%&NOPQ   CD5E+Fa1R !12Fcd+efgh #$ &* # &Ta1iJ3T3T                   # $                                `4ab.,-L OPZ.6G4H.IJ Lcde8 OP  *+,-./e8 Page