SPECIFICATIONS
CDT Size |
|
| |||
|
|
|
| ||
Diagonal visible image area |
| ||||
|
|
|
| ||
Dot Pitch |
| 0.25 mm | |||
|
|
|
|
|
|
Synchronization |
| Horizontal | 30 | - 107 | KHz |
|
|
|
|
|
|
|
| Vertical | 50 | - 160 | Hz |
|
|
|
| ||
Plug and Play |
| DDC1/2B/CI | |||
|
|
|
| ||
Power Saving |
| EPA, VESA DPMS, Nutek Compliant | |||
|
|
|
|
| |
Power Source |
| Vac, 50/60Hz (Free Voltage) | |||
|
|
|
|
| |
Power Consumption |
| 135 W |
| ||
|
|
| |||
494 x 500 x 518mm | |||||
(set with stand) |
|
|
|
| |
|
|
| |||
61.7/28.0 | |||||
|
|
|
| ||
Operating Temperature | 10 | ~ 40°C /50 ~ 104°F | |||
|
|
|
|
|
|
*The specifications are subject to change without notice.
FACTORY PRESET TIMINGS
Mode | Resolution | H.Freq(KHz) | V.Freq(Hz) | Remark | ||
(dots X lines) | ||||||
|
|
|
| |||
VGA 480 | 640 | X 480 | 31.5 | 60 | ||
|
|
|
|
|
| |
VGA 400 | 720 | X 400 | 31.3 | 70 | ||
|
|
|
|
|
| |
VESA 43K | 640 | X 480 | 43.0 | 85 | ||
|
|
|
|
|
| |
VESA 46K | 800 | X 600 | 46.9 | 75 | ||
|
|
|
|
| ||
VESA SVGA 85 | 800 X 600 | 53.7 | 85 | |||
|
|
|
|
|
| |
VESA 60K | 1024 | X 768 | 60.0 | 75 | ||
|
|
|
|
|
| |
VESA 1024/85 | 1024 | X 768 | 68.7 | 85 | ||
|
|
|
|
|
| |
VESA 1280/75 | 1280 | X 1024 | 80.0 | 75 | ||
|
|
|
|
|
| |
VESA 1600/70 | 1600 | X 1200 | 87.5 | 70 | ||
|
|
|
|
|
| |
VESA 1280/85 | 1280 | X 1024 | 91.1 | 85 | ||
|
|
|
|
|
| |
VESA 1600/75 | 1600 | X 1200 | 93.8 | 75 | ||
|
|
|
|
|
| |
VESA 1600/85 | 1600 | X 1200 | 106.3 | 85 | ||
|
|
|
|
|
| |
TROUBLESHOOTING
| Symptom | Check | |
|
|
|
|
| No picture. | Check if power switch and computer power switch | |
|
| are in the on position. | |
|
|
| |
|
|
|
|
|
| Check if the signal cable is correctly connected to | |
|
| the video card. | |
|
|
| |
|
|
|
|
|
| Check if the pins of D subconnector are not bent. | |
|
|
| |
|
|
|
|
|
| Check if the computer is in the power- saving mode. | |
|
|
|
|
| POWER LED is not | Check if power switch is in the on position. | |
| lit. |
|
|
|
|
| |
|
| Check if the power cord is correctly connected. | |
|
|
|
|
| Image is unstable. | Check if the signal cable is suitable to the video card. | |
|
|
|
|
| Image is not | Adjust H &V Size or H&V Center to get the proper | |
| centered, too small | image. | |
| or too large. |
|
|
|
|
|
|
| Picture bounces or a | Keep the devices that may cause electrical | |
| wave pattern is | interference away from the monitor. | |
| present in the |
|
|
|
|
| |
| picture. | See the FCC information at the front cover of the | |
|
| manual. | |
|
|
|
|
| Color looks blotchy. | Operate Degauss once. | |
|
|
|
|
| Picture is blurred. | Adjust Contrast and Brightness. | |
|
|
| |
|
|
|
|
|
| Operate Degauss once. | |
|
|
|
|
| Edges of available | Adjust Geometry Control (Pincushion, Trapezoid..). | |
| area on the screen |
|
|
| are not straight. |
|
|
|
|
|
|
English - 12 | English - 13 |