Compex Technologies WP11A+ manual Configure Compex WP11A Using Web Interface

Page 39

Chapter 5 Configure Compex WP11A Using Web Interface

Starting Point

With Compex WP11A+ in its default setting,

1.Activate uConfig program, click on the “OpenWeb” button.

2.Go to the CONFIGURATION menu and click on Mode Selection. In the Network Mode Setup, select Access Point Client as shown in Figure 5.4b.

Figure 5.4b Selection of Network Mode

3.Click on the “Apply” button. The system will prompt you to reboot your system.

4.Go to uConfig program and wait for the system to refresh the screen. Click on the “OpenWeb” button to proceed. The system will lead you to the authentication page again. Logon again and Compex WP11A+ will be in AP Client Mode.

5.Go to “Mode Selection”. Click on the “Apply” button again. This time, the web page for AP Client Setup will appear.

6.Enter the parameters as shown in Figure 5.5c.

29

Image 39
Contents Page Page FCC Notice Page A., Canada, Latin America and South America Technical Support CentersPage Table of Contents Configuration on Various WAN Type Chapter Configure Compex WP11A+ Using Web InterfaceChapter Setting up Wide Area Network using Gateway Mode Chapter Setting up WAN using Wireless Routing ClientUsing System Tools menu Using Help menuAppendix TCP/IP Configuration Appendix III Configuration and Commands on Telnet Interface Overview Product OverviewProduct Overview IntroductionFeatures and Benefits 4a Front view of Compex WP11A+ Panel Views4b Side view of Compex WP11A+ Section #1 Wlan LED Panel Description IndicatorIndicator Description IP, IPX Technical SpecificationsProduct Overview Package Content Setup ConsiderationsGetting Started Illustration on using Clip holder Stand Hardware InstallationHardware Installation Login into Web-based Interface Software Configuration1b Log in to Compex WP11A+ Software Configuration NAT Software Configuration Dhcp Server Configure Compex WP11A Using Web InterfaceChanging the IP Address of Compex WP11A+ Configuring Dhcp ServerConfigure Compex WP11A Using Web Interface 3a Per Group Pseudo Vlan Subnet View 3c Device in AP Bridge Mode Configure Compex WP11A Using Web Interface 3e Access Point Setup Elaboration of Compex WP11A+ 3g Defining Pseudo Vlan using MAC address 3j Defining the key for 64-bit WEP 3l Delete MAC Address of a client Pseudo Vlan WEP encryption method 4a Physical setup of Wireless LAN-to-LAN Bridge Configure Compex WP11A Using Web Interface 4d Selecting WEP encryption method 4e Encryption entries for 64-bit Setting up Wide Area Network using Gateway Mode Setup on Compex WP11A+ for Broadband Internet Access Setting up Wide Area Network using Gateway Mode Configure Compex WP11A+ using Web Interface 3c Access Point Setup in Gateway Mode Setting up Wide Area Network using Gateway Mode Setting up Wide Area Network using Gateway Mode Setting up Compex WP11A+ as Wireless Routing Client Setting up WAN using Wireless Routing ClientSetting up WAN using Wireless Routing Client Setting up WAN using Wireless Routing Client 2c Selecting WEP encryption method 2d Encryption entries for 64-bit Configuring Static IP Connection Configuration on Various WAN TypeConfiguration on Various WAN Type Configuring Dynamic IP Connection Configuration on Various WAN Type 3a PPP Over Ethernet -WAN Type Configuring PPP over Ethernet Session PPPoEQala DSL 4b Singapore Adsl for SingTel Magix Configuring for SingTel Magix SuperSurf5a Australia BPA Cable -WAN Type Configuring for BigPond Australia BPAConfiguration on Various WAN Type 6a WAN Type Pptp Point to Point Tunneling Protocol PptpConfiguration on Various WAN Type 7a WAN Type JTB Brunei e-Speed JTB BruNet e-SpeedConfiguration on Various WAN Type NAT and Virtual Server Configuring Network Address TranslationDefining Port-Forwarding Virtual Server 3a Configuring Network Address Translation3b NAT Static Port Based Entries Click on the Add button 4a IP Forwarding Option Configuring IP-Forwarding virtual server with Compex WP11A+Click on IP Forwarding button Adding Static Routes Configuring Routing ProtocolRouting Chapter Routing2b Adding Static IP Routing Packet Filtering Packet FilteringFiltering Destination Port Packet Filtering Remote Management Remote ManagementRemote Management System Identity Using System Tools menuSet System Time 2a Synchronizing Compex WP11A+’s timerFirmware Upgrade Save or Reset Settings 5a Reboot System Reboot SystemChange Password Logout Exit uConfig8a uConfig icon at the taskbar Get Technical Help Using Help menuAbout System 2a Bridge/Client Mode System Information Gateway ModeHardware Reset of Compex WP11A+ Hardware Reset of Compex WP11AAppendix I Login to Web-based Interface manually Appendix I Login to Web-based Interface manually Appendix II TCP/IP Configuration Appendix II TCP/IP ConfigurationAII-1 Adding TCP/IP network protocol for Windows 98/98SE/ME Figure AII-3 Select Network Protocol Figure AII-4 Select TCP/IP protocol Figure AII-7 Compex WP11A+ Network Connection Appendix II TCP/IP Configuration AIII-1 Telnet Interface Configuration Appendix III Configuration and Commands on Telnet InterfaceAIII-2 Command Line Interface Commands List Examples AIII-3 How to recover Compex WP11A+ from failed firmware Command ExamplesAppendix III Configuration and Commands on Telnet Interface AIII-4 If you have any problem to accessing to the Internet Figure AIII-3 Remove Proxy server setting