Compex Technologies WP11A+ manual Appendix III Configuration and Commands on Telnet Interface

Page 99

Appendix III Configuration and Commands on Telnet Interface

5.Go to Recovery folder and activate wp11arcv.bat.

The system will go to DOS Prompt automatically. Press any key to restore the firmware. It will run the command from the batch file: TFTP -i 192.168.168.1 PUT Wp11a286.img as shown below.

Figure AIII-2 DOS Prompt Environment

When done, the system will prompt you a message “Transfer successful: 505807 bytes in 1 seconds, 505887 bytes/s”.

When the firmware image file is uploaded, it will copy it to the flashrom. During uploading the firmware image file to Compex WP11A+, the DIAG LED will light up.

NOTE

The firmware image file, which you upload from the CD-ROM may not be the latest version. To get the most updated version, please go to www.compex.com.sg to download the firmware. Do not power down the device as data is being transferred.

Please note that your firmware image file might be different. Please enter the name of that image file.

Please ensure that there is constant power supply to Compex WP11A+ while performing the recovery process.

89

Image 99

Contents Page Page FCC Notice Page A., Canada, Latin America and South America Technical Support CentersPage Table of Contents Configuration on Various WAN Type Chapter Configure Compex WP11A+ Using Web InterfaceChapter Setting up Wide Area Network using Gateway Mode Chapter Setting up WAN using Wireless Routing ClientUsing System Tools menu Using Help menuAppendix TCP/IP Configuration Appendix III Configuration and Commands on Telnet Interface Overview Product OverviewProduct Overview IntroductionFeatures and Benefits 4a Front view of Compex WP11A+ Panel Views4b Side view of Compex WP11A+ Section #1 Wlan LED Panel Description IndicatorIndicator Description IP, IPX Technical SpecificationsProduct Overview Package Content Setup ConsiderationsGetting Started Illustration on using Clip holder Stand Hardware InstallationHardware Installation Login into Web-based Interface Software Configuration1b Log in to Compex WP11A+ Software Configuration NAT Software Configuration Dhcp Server Configure Compex WP11A Using Web InterfaceChanging the IP Address of Compex WP11A+ Configuring Dhcp ServerConfigure Compex WP11A Using Web Interface 3a Per Group Pseudo Vlan Subnet View 3c Device in AP Bridge Mode Configure Compex WP11A Using Web Interface 3e Access Point Setup Elaboration of Compex WP11A+ 3g Defining Pseudo Vlan using MAC address 3j Defining the key for 64-bit WEP 3l Delete MAC Address of a client Pseudo Vlan WEP encryption method 4a Physical setup of Wireless LAN-to-LAN Bridge Configure Compex WP11A Using Web Interface 4d Selecting WEP encryption method 4e Encryption entries for 64-bit Setting up Wide Area Network using Gateway Mode Setup on Compex WP11A+ for Broadband Internet Access Setting up Wide Area Network using Gateway Mode Configure Compex WP11A+ using Web Interface 3c Access Point Setup in Gateway Mode Setting up Wide Area Network using Gateway Mode Setting up Wide Area Network using Gateway Mode Setting up Compex WP11A+ as Wireless Routing Client Setting up WAN using Wireless Routing ClientSetting up WAN using Wireless Routing Client Setting up WAN using Wireless Routing Client 2c Selecting WEP encryption method 2d Encryption entries for 64-bit Configuring Static IP Connection Configuration on Various WAN TypeConfiguration on Various WAN Type Configuring Dynamic IP Connection Configuration on Various WAN Type 3a PPP Over Ethernet -WAN Type Configuring PPP over Ethernet Session PPPoEQala DSL 4b Singapore Adsl for SingTel Magix Configuring for SingTel Magix SuperSurf5a Australia BPA Cable -WAN Type Configuring for BigPond Australia BPAConfiguration on Various WAN Type 6a WAN Type Pptp Point to Point Tunneling Protocol PptpConfiguration on Various WAN Type 7a WAN Type JTB Brunei e-Speed JTB BruNet e-SpeedConfiguration on Various WAN Type NAT and Virtual Server Configuring Network Address TranslationDefining Port-Forwarding Virtual Server 3a Configuring Network Address Translation3b NAT Static Port Based Entries Click on the Add button 4a IP Forwarding Option Configuring IP-Forwarding virtual server with Compex WP11A+Click on IP Forwarding button Adding Static Routes Configuring Routing ProtocolRouting Chapter Routing2b Adding Static IP Routing Packet Filtering Packet FilteringFiltering Destination Port Packet Filtering Remote Management Remote ManagementRemote Management System Identity Using System Tools menuSet System Time 2a Synchronizing Compex WP11A+’s timerFirmware Upgrade Save or Reset Settings 5a Reboot System Reboot SystemChange Password Logout Exit uConfig8a uConfig icon at the taskbar Get Technical Help Using Help menuAbout System 2a Bridge/Client Mode System Information Gateway ModeHardware Reset of Compex WP11A+ Hardware Reset of Compex WP11AAppendix I Login to Web-based Interface manually Appendix I Login to Web-based Interface manually Appendix II TCP/IP Configuration Appendix II TCP/IP ConfigurationAII-1 Adding TCP/IP network protocol for Windows 98/98SE/ME Figure AII-3 Select Network Protocol Figure AII-4 Select TCP/IP protocol Figure AII-7 Compex WP11A+ Network Connection Appendix II TCP/IP Configuration AIII-1 Telnet Interface Configuration Appendix III Configuration and Commands on Telnet InterfaceAIII-2 Command Line Interface Commands List Examples AIII-3 How to recover Compex WP11A+ from failed firmware Command ExamplesAppendix III Configuration and Commands on Telnet Interface AIII-4 If you have any problem to accessing to the Internet Figure AIII-3 Remove Proxy server setting