Citizen Systems CBM-730, CBM-720, CBM-750 manual Declaration of Conformity

Page 2

CBM-710/720/730/750 User’s Manual

	Declaration of Conformity
Manufacturer’s Name :	Japan CBM Corporation
Manufacturer’s Address:	CBM Bldg., 5-68-10, Nakano, Nakano-ku
	Tokyo, 164-0001, Japan
Declare the Product
Product Name:	Dot Matrix Printer
Model Number(s):	CBM-710,720,750 Series
	(CBM-710R, CBM-710P, CBM-720R, CBM-720P,
	CBM-750R, CBM-750P)
	(S.No.0090001 ~ )
Conform to the following Standards:
LVD:	: EN60950	: A4:1997
EMC:	: EN55022	: 1998 Class A
	: EN61000-3-2	: 1995+A1:1998+A2:1998
	: EN61000-3-3	: 1995
	: EN55024	: 1998
	: EN61000-4-2	: 1995 ± 4KV CD, ± 8KV AD
	: EN61000-4-3	: 1996 3V/m, 80MH-1000MHz AM 1KHz 80%
	: EN61000-4-4	: 1995 ± 1.0KV (AC Mains), ± 0.5KV (Signal Lines)
	: EN61000-4-5	: 1995 ± 1KV (Normal mode), ± 2KV (Cmmon mode)
	: EN61000-4-6	: 1996 3V, 0.15MHz-80MHz AM 1KHz 80%
	: EN61000-4-8	: 1993 50Hz, 1A/m
	: EN61000-4-11	: 1994 0%, 5000ms/ 70%, 500ms/ 0%, 10ms

Supplementary Information

“The product complies with the requirements of the Low Voltage Directive 73/23/EEC, 93/68/EEC and the EMC Directive 89/336/EEC, 92/31/EEC, 93/68EEC”

Place	Tokyo, Japan	Signature:
Date	September, 2000
		Full Name :	Mikio Moriya
		Position :	General Manager
			R & D Department

European Contact :

Norco Declaration AB

Box 7146 S-250 07 Helsingborg, Sweden

WARNING: This is a Class A products. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

This declaration is applied only for 230V model.

CITIZEN

Image 2

Contents Page Declaration of Conformity Important Safety Instructions Sicherheitshinweis Contents 11.1 Introduction FeaturesAccessories Type Classifications CBM-710 23 RSpecifications General SpecificationsCBM-710 CBM-720 Paper Specifications Print FormatBlock Diagram External Appearance and Pars Descriptions CBM-710 External AppearanceCBM-720 External Appearance Front ViewCBM-730 External Appearance CBM-750 External Appearance Part Descriptions Setting and Removing the Paper and Ribbon Covers OperationOpening and Closing the Cutter Unit CBM-720. CBM-750 Installing the Cassette Ribbon Installing and Changing the Paper Installing the PaperCitizen Citizen Paper End Detector Procedures for Actuating the Self Print FunctionSelf Print Function Changing the PaperInstallation of the CBM-750 Clearing the Input Buffer Input Buffer BACK-UP FunctionInput Buffer Back-up Parallel Interface SpecificationsConnector Pin Assignment Description of Input/Output Signals Input/Output SignalsElectrical Characteristics Timing Chart Serial Interface DTR Description of Input/Output Signals Error Detection Data CompositionData Receiving Control BufferingOutput DTR, TD Ready Setting DIP Switch DS1 Function SelectionDIP Switch DS2 Serial interface specifications only Slide Switch Setting Serial interface specifications only DIP Switch and Slide Switch LocationsPrint Control Functions Control CodesEnlarged character command Input Data FormatsPrint command Enlarged character cancel commandPaper feed command Clear commandBuzzer Command Initial Set CommandInverted character command Underline Command Graphic Command Graphic Type OnlyPin 13 1/9 inch Line Feed Pitch Set Command Graphic Type14 2/9 inch Line Feed Pitch Set Command Graphic Type Form Feed Command Skip Perforation Cancel Command 2nd byte 4EH 3rd byte N7 N6 N5 N4 N3 N2 N1 Binary digitalFull Cut Command 1st byte Character Code Tables International Character CodesIndividual Country Character Codes Exterior MaintenanceMaintenance Procedures InteriorExternal Dimensions CBM-710CBM-720 Paper Winder Unit AW-2 CBM-730 CBM-750 Information Systems Division Head Office