Citizen Systems CBM-730, CBM-720, CBM-750 manual Part Descriptions

Page 17

CBM-710/720/730/750 User ’s Manual

5. 5

Part Descriptions

 

(1)

Power Cord

Attach the connector end to the printer inlet, and insert the plug end into an electric

 

 

outlet.

(2)

Inlet

This is the electric power inlet. Attach the connector end of the power cord here.

(3 )

Power Switch

Power is supplied to the printer by turning this switch on.

(4)

Line Switch

When this switch is pressed, the printer enters select (on line) status. When pressed

 

 

again, the printer enters deselect (off line) status. This switch is also used when

 

 

clearing an alarm condition.

(5)

LF Switch

Paper feeding is performed when this switch is pressed (in deselect status only).

 

 

This is used when inserting the paper and for spacing up etc.

(6)

Power Lamp

This lights up when the power switch is "on" and goes out when turned "off".

(7)

On Line Lamp

This lights up when the printer is in select (on line) status, and goes out when in

 

 

deselect (off line) status. Printing operation is performed only when this lamp is on.

(8)

Alarm Lamp

This lights up when printer operation is abnormal. When in an alarm condition,

 

 

printing and line feed operations are not performed.

(9)

Interface Connector

Connects through a cable to a computer etc. Please be certain that power to both

 

 

the printer and the computer are turned off when connection is made.

(l0)

Connector Cover

Covers the connector which is used for the paper winder mechanism (AW-2).

(l1)

Paper Cover

Opens when replacing the paper roll.

(l2)

Ribbon Cover

Opens when replacing the ribbon.

(l3)

Top Case

 

(l4)

Bottom Plate

 

(l5)

Printer Cover

 

(l6)

Paper-Feed Knob

 

(l7)

Bottom Base

 

(l8)

Base Stoppers

 

11

CITIZEN

Image 17
Contents Page Declaration of Conformity Important Safety Instructions Sicherheitshinweis Contents 11.1 Introduction FeaturesAccessories CBM-710 23 R Type ClassificationsGeneral Specifications SpecificationsCBM-710 CBM-720 Print Format Paper SpecificationsBlock Diagram CBM-710 External Appearance External Appearance and Pars DescriptionsFront View CBM-720 External AppearanceCBM-730 External Appearance CBM-750 External Appearance Part Descriptions Operation Setting and Removing the Paper and Ribbon CoversOpening and Closing the Cutter Unit CBM-720. CBM-750 Installing the Cassette Ribbon Installing the Paper Installing and Changing the PaperCitizen Citizen Self Print Function Procedures for Actuating the Self Print FunctionPaper End Detector Changing the PaperInstallation of the CBM-750 Clearing the Input Buffer Input Buffer BACK-UP FunctionInput Buffer Back-up Parallel Interface SpecificationsConnector Pin Assignment Input/Output Signals Description of Input/Output SignalsElectrical Characteristics Timing Chart Serial Interface DTR Description of Input/Output Signals Data Composition Error DetectionBuffering Data Receiving ControlOutput DTR, TD Ready Function Selection Setting DIP Switch DS1DIP Switch DS2 Serial interface specifications only DIP Switch and Slide Switch Locations Slide Switch Setting Serial interface specifications onlyControl Codes Print Control FunctionsInput Data Formats Enlarged character commandPaper feed command Enlarged character cancel commandPrint command Clear commandBuzzer Command Initial Set CommandInverted character command Graphic Command Graphic Type Only Underline CommandPin 13 1/9 inch Line Feed Pitch Set Command Graphic Type14 2/9 inch Line Feed Pitch Set Command Graphic Type Form Feed Command 2nd byte 4EH 3rd byte N7 N6 N5 N4 N3 N2 N1 Binary digital Skip Perforation Cancel CommandFull Cut Command 1st byte International Character Codes Character Code TablesIndividual Country Character Codes Maintenance Procedures MaintenanceExterior InteriorCBM-710 External DimensionsCBM-720 Paper Winder Unit AW-2 CBM-730 CBM-750 Information Systems Division Head Office