Campbell Hausfeld SDM-SIO4 manual Basic Commands

Page 26

SDM-SIO4 User Guide

Control characters can be entered for all commands in a similar way:

∙^M is carriage return, ^J line feed etc.

∙^^ means ^

∙"" means "

∙]] means ]

∙&& means &

∙&0d means line feed

∙&hex,hex used to enter 2-character hex. codes (0-9, A-F)

4.3Basic Commands

fltst [string number] ["filter definition"]

This command stores a filter definition to a string number 0..255.

Example: fltst 22 "ccci[x]Fs"

The above example stores the filter definition in filter string 22.

See Section 3 for filter types.

strst [string number] ["string definition"]

This command stores a user text string definition to a string number 0..255.

Example: strst 22 """This is a string""^M^J"

The above example stores the string definition "This is a string"crlf in string 22.

This string will include the two quotation marks, as shown.

fmtst [string number] ["format definition"]

This command will store a formatter definition to a string number 0..255.

Example: fmtst 22 "i[volts=]f4:2" (result would be, for example, volts=12.7)

The above example stores the formatter definition in string 22.

See Section 3 for formatter types.

strdelete [string number]

This command deletes a stored filter, formatter or text string 0..255 from memory.

strrd [string number]

This command outputs the stored string or definition 0..255 to the command line.

NOTE 1. When string definitions are stored, all control characters are converted and so the string may not be identical to the one you typed in.

2. Formatter and filter strings cannot be read by this command

4-2

Image 26

Contents Issued Page Guarantee Page Contents Data Error Detection Appendix A. Ascii TableWhat is the SDM-SIO4? IntroductionDatalogger Command Control Serial Ports SpecificationsSDM-SIO4 Serial Port Pin Configuration Serial Port BuffersCase Power RequirementsSDM Port Environmental Operating RangeOther Key Features Page Address Settings Installation and Hardware Set-UpSetting the SDM Address Selector Block Settings SDM AddressTransient Protection and Grounding Selecting RS232 or 5V Logic for Each PortConnections to the SDM-SIO4 No. of Flashes Description of error/status Power-on Tests the Status LEDStatus LED Error Codes Page Method of Entering Special / Control Characters Understanding How the SDM-SIO4 Handles DataIntroduction Simple Filters Input FiltersFilter Types Filter Strings Ibn8Ficn8F Predefined Filter Strings Output FormattingSimple Output Formatter Filter No Filter String UsedOutput Format Strings Fmtst 123 z261 f62 iBattery z257 f61z273 CR10X Program ExampleGet battery voltage Get panel temperatureProgramming the SDM-SIO4 Command Line Operation and StructureEntering Commands Basic Commands Advanced Commands Bytewr address byte ErrorresHexdump start address number of bytes WD n Wderr n Wdaddr nTestio test# Testio returnsPage Programming the Datalogger Instruction 113 ParametersParameter 8 Starting Input Location Commands and Options Parameters 4, 5Parameter 7 Values per Rep Parameters 9 and 10 Multiplier and OffsetCommand 1 Poll of Available Data Understanding Parameter Options and Returned ValuesCommand 4 Send Data to Datalogger Command 2 SignaturesCommand 3 Flush all Receive Buffers Command 5 StatusCommand 8 Poll Tx Buffers for Data Command 6 Flush Transmit BufferCommand 7 Activate Command Line Command 9 Flush Converted Data BufferCommand 321 Execute Command Line Command Command 67 Get Return CodeCommand 320 Send Byte Data to SDM-SIO4 Program Example for P113 CommandExecute the command line string Command 1026 Serial Port Status Command 1024 Send String to DeviceCommand 1025 Transmit a Byte First Value ReturnedThird Value Returned First Command Option Reset Error CountersSecond Value Returned Fourth Value ReturnedCommand 1027 ‘Manual’ Handshake Mode Command 2049 Set Communications ParametersFirst Command Option Parameter Second Command Option ParameterCommand 2054 Set Up Receive Filter String Number or Character Code Example CR10X Program SDM-SIO4 Configuration ExamplesCommand 2305 Transmit Bytes Get two floating point numbers into locations 1 End of serial and filter setupSet flag one high so the above will only be done once Example CR10X Program Using Instruction P113 Command Strst 101 Send DataJMSet up the filter and then send string Wait long enough for sensor to send dataTime stamp Sensors Which Send Data Out Without PromptingGet data from SDM-SIO4 and put into locations 1 Instantaneous sample form the sensorExample CR10X Program without Polling or Interrupts Fltst 200 tdataA5xffGet the two floating point values from the SDM-SIO4 Example CR10X Program using the Polling MethodEnd of set up Instantaneous values stored to final storageDo filter set-up only if flag one is clear Set up string filterDelay required by filter set-up command Set flag one high so the filter set-up is only done onceInstantaneous value stored into final storage Example CR10X Program using InterruptsGet voltages into locations 3 and 4 if poll was true Set control port 8 to i/p so it can be used as an interrupt Do filter setup only if flag one is clearDelay required by filter setup command Instantaneous readings stored into final storage Interrupt routine for control portGet voltages into locations 3 End of interrupt routineOutputting Datalogger Data Return Error Codes Flushing the Input and Output BuffersReceived Data Data Error DetectionError Detection with the SDM-SIO4 SDM-SIO4 User Guide Fltst 100 TFrequency=xg2n10fCCG8 Example of Using Received Data Filters2 CR10X Program Example Tell the SDM-SIO4 to use filter string Minimum delay of 4ms is required by the above P113End of filter setup End of get data Transmitted Data CRC32Example of Using Transmitted Data Filters Fmtst 100 g1i123456789G8Alternative CR10X Program Fmtst 100 g1 Fmtst 101 isome data Fmtst 102 f62 G8Minimum delay of 3.8ms is required after this command Use formatter string 100 to set up the CRC16 on portMinimum delay of 1ms is required after this command Send the Ascii characters ‘Y’ and ‘Z’ to portCRC16-CCITT-IBM Data Error Detection Page Appendix A. Ascii Table Dec CharPage Stop Bits Appendix B. Serial Port Data Transfer ModesBaud rates Data LengthParity Bits Serial Handshake Modes