Campbell Hausfeld SDM-SIO4 manual Command 6 Flush Transmit Buffer, Command 7 Activate Command Line

Page 35

Section 5. Programming the Datalogger

If any of these four digits is greater than zero then data is available.

Values per repetition = 2

5.2.7 Command 6: Flush Transmit Buffer

This command flushes the SDM-SIO4 transmit buffer of data it is waiting to send.

Values per repetition = 0

5.2.8 Command 7: Activate Command Line

This command simulates pressing the push button on the SDM-SIO4 which activates the command line mode on the port determined by the mode. If the mode parameter of P113 is 0, the command line will be on the currently defined port. If the parameter is 1-4, then the command line will be on the port number specified.

Values per repetition = 0

5.2.9 Command 8: Poll Tx Buffers for Data

This command polls the Tx buffers to see if they have data.

This command has no additional options after the command. The SDM-SIO4 returns one Campbell Scientific floating point number to indicate if it has data as below:

Port 4 has data Port 3 has data

Port 2 has data

Port 1 has data

x x x x

If any of these four digits is greater than zero then the buffer has data.

Values per repetition = 1

5.2.10 Command 9: Flush Converted Data Buffer

This command flushes the converted data buffer of data that is available for the datalogger to collect.

Values per repetition = 0

5.2.11 Command 66: Send Single-Byte Data to Datalogger

This command requests the SDM-SIO4 to send single-byte binary data, which is written one byte per location for all values/rep. If no data is available then the digit 255 is stored in the input location. This command could be used, for example, to get data from filter strings of type c (read any byte) and Nn (read ‘n’ bytes) – see Section 3.

5-5

Image 35

Contents Issued Page Guarantee Page Contents Appendix A. Ascii Table Data Error DetectionIntroduction What is the SDM-SIO4?Datalogger Command Control Serial Port Buffers SpecificationsSDM-SIO4 Serial Port Pin Configuration Serial PortsEnvironmental Operating Range Power RequirementsSDM Port CaseOther Key Features Page Selector Block Settings SDM Address Installation and Hardware Set-UpSetting the SDM Address Address SettingsTransient Protection and Grounding Selecting RS232 or 5V Logic for Each PortConnections to the SDM-SIO4 No. of Flashes Description of error/status Power-on Tests the Status LEDStatus LED Error Codes Page Method of Entering Special / Control Characters Understanding How the SDM-SIO4 Handles DataIntroduction Simple Filters Input FiltersFilter Types Filter Strings Ibn8Ficn8F Filter No Filter String Used Output FormattingSimple Output Formatter Predefined Filter StringsOutput Format Strings CR10X Program Example Fmtst 123 z261 f62 iBattery z257 f61z273Get panel temperature Get battery voltageProgramming the SDM-SIO4 Command Line Operation and StructureEntering Commands Basic Commands Advanced Commands WD n Wderr n Wdaddr n ErrorresHexdump start address number of bytes Bytewr address byteTestio returns Testio test#Page Instruction 113 Parameters Programming the DataloggerParameters 9 and 10 Multiplier and Offset Commands and Options Parameters 4, 5Parameter 7 Values per Rep Parameter 8 Starting Input LocationUnderstanding Parameter Options and Returned Values Command 1 Poll of Available DataCommand 5 Status Command 2 SignaturesCommand 3 Flush all Receive Buffers Command 4 Send Data to DataloggerCommand 9 Flush Converted Data Buffer Command 6 Flush Transmit BufferCommand 7 Activate Command Line Command 8 Poll Tx Buffers for DataProgram Example for P113 Command Command 67 Get Return CodeCommand 320 Send Byte Data to SDM-SIO4 Command 321 Execute Command Line CommandExecute the command line string First Value Returned Command 1024 Send String to DeviceCommand 1025 Transmit a Byte Command 1026 Serial Port StatusFourth Value Returned First Command Option Reset Error CountersSecond Value Returned Third Value ReturnedCommand 2049 Set Communications Parameters Command 1027 ‘Manual’ Handshake ModeSecond Command Option Parameter First Command Option ParameterCommand 2054 Set Up Receive Filter String Number or Character Code Example CR10X Program SDM-SIO4 Configuration ExamplesCommand 2305 Transmit Bytes Get two floating point numbers into locations 1 End of serial and filter setupSet flag one high so the above will only be done once Strst 101 Send DataJM Example CR10X Program Using Instruction P113 CommandWait long enough for sensor to send data Set up the filter and then send stringInstantaneous sample form the sensor Sensors Which Send Data Out Without PromptingGet data from SDM-SIO4 and put into locations 1 Time stampFltst 200 tdataA5xff Example CR10X Program without Polling or InterruptsInstantaneous values stored to final storage Example CR10X Program using the Polling MethodEnd of set up Get the two floating point values from the SDM-SIO4Set flag one high so the filter set-up is only done once Set up string filterDelay required by filter set-up command Do filter set-up only if flag one is clearInstantaneous value stored into final storage Example CR10X Program using InterruptsGet voltages into locations 3 and 4 if poll was true Set control port 8 to i/p so it can be used as an interrupt Do filter setup only if flag one is clearDelay required by filter setup command End of interrupt routine Interrupt routine for control portGet voltages into locations 3 Instantaneous readings stored into final storageOutputting Datalogger Data Flushing the Input and Output Buffers Return Error CodesReceived Data Data Error DetectionError Detection with the SDM-SIO4 SDM-SIO4 User Guide Fltst 100 TFrequency=xg2n10fCCG8 Example of Using Received Data Filters2 CR10X Program Example Tell the SDM-SIO4 to use filter string Minimum delay of 4ms is required by the above P113End of filter setup End of get data CRC32 Transmitted DataFmtst 100 g1i123456789G8 Example of Using Transmitted Data FiltersFmtst 100 g1 Fmtst 101 isome data Fmtst 102 f62 G8 Alternative CR10X ProgramSend the Ascii characters ‘Y’ and ‘Z’ to port Use formatter string 100 to set up the CRC16 on portMinimum delay of 1ms is required after this command Minimum delay of 3.8ms is required after this commandCRC16-CCITT-IBM Data Error Detection Page Dec Char Appendix A. Ascii TablePage Data Length Appendix B. Serial Port Data Transfer ModesBaud rates Stop BitsSerial Handshake Modes Parity Bits