Campbell Hausfeld SDM-SIO4 manual Programming the Datalogger, Instruction 113 Parameters

Page 31

Section 5. Programming the Datalogger

The datalogger instruction specific to the SDM-SIO4 is P113 (CR7 and CR10/10X only). (Please check with Campbell Scientific to see if your version of the operating system supports this.) The instruction has the following format:

Parameter No.	Description
01	Reps (number of adjacent addressed SDM-SIO4s)
02	Address of SDM-SIO4 (0..15)
03	Mode (0..5)
04	Command (0..9999).
05	First command option (0..9999)
06	Second command option (0..9999)
07	Values per rep
08	Starting input location
09	Multiplier
10	Offset

5.1 Instruction 113 Parameters

5.1.1 Parameter 1 — Reps

This specifies the number of times you wish this command to repeat for each SDM-SIO4 connected to the datalogger with sequential addresses. This will normally be set to one.

5.1.2 Parameter 2 — Address

This is the address of the SDM-SIO4 that the instruction applies to.

See Section 2 – ‘Installation and Hardware Set-Up’ for information on setting the

SDM-SIO4 address

5.1.3 Parameter 3 — Mode

This defines which port the command applies to:

Code	Port
1	Send/Receive port 1
2	Send/Receive port 2
3	Send/Receive port 3
4	Send/Receive port 4
5	Send to all four ports (global)

5.1.4 Parameters 4, 5 and 6 — SDM-SIO4 Command

This command (with up to two options) defines exactly what the instruction will do. Where no options are needed, enter values of 0000 for parameters 5 and 6.

5-1

Image 31

Contents Issued Page Guarantee Page Contents Appendix A. Ascii Table Data Error DetectionIntroduction What is the SDM-SIO4?Datalogger Command Control Serial Port Buffers SpecificationsSDM-SIO4 Serial Port Pin Configuration Serial PortsEnvironmental Operating Range Power RequirementsSDM Port CaseOther Key Features Page Selector Block Settings SDM Address Installation and Hardware Set-UpSetting the SDM Address Address SettingsConnections to the SDM-SIO4 Selecting RS232 or 5V Logic for Each PortTransient Protection and Grounding Status LED Error Codes Power-on Tests the Status LEDNo. of Flashes Description of error/status Page Introduction Understanding How the SDM-SIO4 Handles DataMethod of Entering Special / Control Characters Filter Types Input FiltersSimple Filters Filter Strings Ibn8Ficn8F Filter No Filter String Used Output FormattingSimple Output Formatter Predefined Filter StringsOutput Format Strings CR10X Program Example Fmtst 123 z261 f62 iBattery z257 f61z273Get panel temperature Get battery voltageEntering Commands Command Line Operation and StructureProgramming the SDM-SIO4 Basic Commands Advanced Commands WD n Wderr n Wdaddr n ErrorresHexdump start address number of bytes Bytewr address byteTestio returns Testio test#Page Instruction 113 Parameters Programming the DataloggerParameters 9 and 10 Multiplier and Offset Commands and Options Parameters 4, 5Parameter 7 Values per Rep Parameter 8 Starting Input LocationUnderstanding Parameter Options and Returned Values Command 1 Poll of Available DataCommand 5 Status Command 2 SignaturesCommand 3 Flush all Receive Buffers Command 4 Send Data to DataloggerCommand 9 Flush Converted Data Buffer Command 6 Flush Transmit BufferCommand 7 Activate Command Line Command 8 Poll Tx Buffers for DataProgram Example for P113 Command Command 67 Get Return CodeCommand 320 Send Byte Data to SDM-SIO4 Command 321 Execute Command Line CommandExecute the command line string First Value Returned Command 1024 Send String to DeviceCommand 1025 Transmit a Byte Command 1026 Serial Port StatusFourth Value Returned First Command Option Reset Error CountersSecond Value Returned Third Value ReturnedCommand 2049 Set Communications Parameters Command 1027 ‘Manual’ Handshake ModeSecond Command Option Parameter First Command Option ParameterCommand 2054 Set Up Receive Filter String Number or Character Code Command 2305 Transmit Bytes SDM-SIO4 Configuration ExamplesExample CR10X Program Set flag one high so the above will only be done once End of serial and filter setupGet two floating point numbers into locations 1 Strst 101 Send DataJM Example CR10X Program Using Instruction P113 CommandWait long enough for sensor to send data Set up the filter and then send stringInstantaneous sample form the sensor Sensors Which Send Data Out Without PromptingGet data from SDM-SIO4 and put into locations 1 Time stampFltst 200 tdataA5xff Example CR10X Program without Polling or InterruptsInstantaneous values stored to final storage Example CR10X Program using the Polling MethodEnd of set up Get the two floating point values from the SDM-SIO4Set flag one high so the filter set-up is only done once Set up string filterDelay required by filter set-up command Do filter set-up only if flag one is clearGet voltages into locations 3 and 4 if poll was true Example CR10X Program using InterruptsInstantaneous value stored into final storage Delay required by filter setup command Do filter setup only if flag one is clearSet control port 8 to i/p so it can be used as an interrupt End of interrupt routine Interrupt routine for control portGet voltages into locations 3 Instantaneous readings stored into final storageOutputting Datalogger Data Flushing the Input and Output Buffers Return Error CodesError Detection with the SDM-SIO4 Data Error DetectionReceived Data SDM-SIO4 User Guide 2 CR10X Program Example Example of Using Received Data FiltersFltst 100 TFrequency=xg2n10fCCG8 End of filter setup Minimum delay of 4ms is required by the above P113Tell the SDM-SIO4 to use filter string End of get data CRC32 Transmitted DataFmtst 100 g1i123456789G8 Example of Using Transmitted Data FiltersFmtst 100 g1 Fmtst 101 isome data Fmtst 102 f62 G8 Alternative CR10X ProgramSend the Ascii characters ‘Y’ and ‘Z’ to port Use formatter string 100 to set up the CRC16 on portMinimum delay of 1ms is required after this command Minimum delay of 3.8ms is required after this commandCRC16-CCITT-IBM Data Error Detection Page Dec Char Appendix A. Ascii TablePage Data Length Appendix B. Serial Port Data Transfer ModesBaud rates Stop BitsSerial Handshake Modes Parity Bits