Braun MCA166-USB user manual Power management, Switching on

Page 7

2.2.1 Power management

The MCA166-USB works with a built in rechargeable Li-Ion battery, which has no memory effect and is deep discharge and short circuit protected. If the device is working, the remaining battery life time is permanently checked. When the battery voltage has dropped down to 6.8 Volts, while a data collection is in progress, the MCA166-USB gives out a warning to the user (the lamp will flash irregularly and the software will show an error message). The running measurement is automatically stopped and the detector high voltage together with the preamplifier power supply will be switched off.

Now the user can transfer the measured spectrum to the computer, but should switch the device off afterwards or connect the charger. If the user does not respond, and the battery life time is nearly used up (battery voltage 6.5 Volts) , the device switches off automatically. It is made sure, that the set up and the spectrum gathered previously is saved in the memory of the MCA166-USB for at least several month.

The remaining battery life time is sufficient to transfer the measured spectrum to a computer. It is recommended, before reading out the MCA166-USB, to connect it to the charger.

In the case that the battery voltage drops below its lowest value, the battery itself switches off. This can be, for example, the result of a lasting short circuit at the preamplifier power supply. As a consequence the internal setup and the measured values are lost. The MCA166-USB has to be connected to the charger to recharge the battery.

2.2.2 Switching on

The MCA166-USB is set into operation by turning the power switch on (see Figure 1). After that, the green power ON LED flashes with a frequency of 2.5 Hz if no MMCA software runs on the connected computer. If the power switch is already in position ON (for example after an automatic switch off due to a complete loss of battery power) switch OFF and to ON again. When the power ON LED does not flash, connect the MCA166- USB with the charger and repeat once more. The MCA166-USB is on line with the computer if the LED flashes with 1.2 Hz. Irregular flashing of the lamp indicates an error.

Figure 1:

Front

Panel of

MCA166-

USB

7

Image 7
Contents MCA166-USB Exclusion of liability MCA166-USBTable of Contents Appendix Introduction Hardware Users safety informationGeneral Description Switching on Power managementCharging the MCA166-USB Connecting the MCA166-USB to a ComputerConnection of detectors Software Additional external battery pack and Power PackOverview UF6 MS-DOS, WinUF6 Spec MS-DOS, WinSPEC WindowsMCS MS-DOS, WinMCS Windows U235 MS-DOS, WinU235 WindowsWinSCAN RateIdentify Source Target MCAPlot and MCAPrintMiscellaneous MCA166-USB parameters for use with different detectorsIsotope Half-life Energy keV Branching ratio % Some of the most important photon energiesMCA166-USB Hardware Specifications Technical DataAmplifier 2 ADC High Voltage Power supplyBattery Preamplifier VoltagesComputer Interface Mechanical specificationEnvironmental ratings Block Diagram of the MCA166-USB Diagrams and pin connectionsContact Voltage Max. Current Contact SignalHV-Inhibit mode2 Troubleshooting Page MCA166-USB $SPECREM File Content ExplanationFile Content Explanation $ROI File Content Explanation $ENERFIT$INPUT File Content $ADC$PRESETS $FASTDISCR 400 $SLOWDISCR$MCSTIME $POWERSTATE$MCSCHANNELS $MCSINPUT$SPECINTEGRAL File Content Explanation $RECCOUNTER$RECERRORCOUNTER File Content Explanation $WINSPECINFOAnalysismga AnalysiscsratioIcod $WINSPECINFOLOT LOT ID MBA File Content Explanation $UF6INSPINFO$WINSCANINFO OUTMBA LOT LOT ID File Content Explanation $INSPINFOArea and the Area Uncertainty Function Appendix 2 MCA166-USB algorithm, formulasSmooth CentroidStrip Appendix 3 Description of the communication DLLs8 MCA166-USB A3.1.3 Functions to work with the MCA Mmcastartacquire MmcaresetMmcacleartime MmcasetmodemcaMmcasetmodemcs MmcaclearmemoryMmcasetpresetintegral MmcasetpresetnoneMmcasetpresetlivetime MmcasetpresetrealtimeMmcasetmcschannel MmcasetadcresdiscrMmcasetroi MmcasetrepeatMmcasetmcsinputttl MmcasetmcsinputicrMmcasetmcsinputdiscr Mmcasetmcainputdirectpos MmcasetgainMmcasetmcainputamplifierpos MmcasetmcainputamplifiernegMmcasetpileuprejection MmcasetthresholdMmcasetshapingtimelow MmcasetshapingtimehighMMCASETPZCVALUE19 MmcasetfastMmcasetslow MMCASETPZCMANUAL18Mmcasethighvoltages MmcasetpreamplifierpowerMmcasetstabilisation MmcasetstabparamMmcasetuserdata MmcasettdfMMCASETUF6ROIS Mmcaqueryuserdata Contents of the Mmca User Date memory21Page Mmcaquerypower Mcamode MODEMCA, Modemcs MmcaquerystateMcastabresult STABSTARTED, Stabactive DTC STABIDLE, StaberrorMcainputadc Adcamplifier ADC Directpos Adcdirectneg Mcainputpol Inputpolaritypositive InputpolaritynegativeMmcaquerysystemdata MMCAQUERYIMAGE36 Mmcaqueryenrichment MmcaqueryspectraMmcaqueryonline MMCAQUERYUF6INFOMMCAQUERYUF6ROIS MmcaquerycentroidMmcaqueryvoltagecurrent Statestop CmdinitCmdstart CmdstopClearmemory = Cleartime Clearroi Clearall CmdsetmodeModemca Modemcs CmdclearLLD, ULD CmdsetpresetsPresetnone Presetreal Presetlive Presetint Presetarea CmdsetadcresdiscrCmdsetmcschannel CmdsetrepeatCmdsettimeperchannel Cmdsetinputpolarity CmdsetgainCmdsetmcainput Cmdsetthreshold CmdsetmcsinputCmdsetshapingtime Cmdsetfast CmdsetpurCmdsetslow Cmdsetpzctimeoffset CmdsetpzcCmdsetstabparam Cmdsetbias CmdsetpreamplifierpowerCMDSETUF6ROI CmdsettdfCmdsetuserdata Cmdqueryimage CmdquerypowerCmdquerystate CmdqueryspectraCmdsystemdata CmdqueryuserdataCmdquerycentroid CMDQUERYUF6ROIS CmdqueryenrichmentAppendix 5 Changing the MCA166-USB Firmware

MCA166-USB specifications

The Braun MCA166-USB is a compact and versatile charging device designed for modern lifestyles. This product expertly combines functionality with portability, making it an essential accessory for people on the go. One of the key features of the Braun MCA166-USB is its dual charging capability. It comes equipped with multiple USB ports, allowing users to charge various devices simultaneously, from smartphones to tablets. This multi-device functionality eliminates the need for multiple chargers cluttering your workspace or travel bag.

The device supports fast charging technology, which is particularly beneficial for users who need quick power boosts. With a maximum output of 2.4A per port, the Braun MCA166-USB ensures that your devices are energized swiftly, reducing downtime and keeping you connected during busy days. Additionally, the device is compatible with a wide range of charging protocols, offering versatility for different brands and models.

The Braun MCA166-USB features an intelligent charging system that recognizes the connected device and delivers the optimal charging current. This not only enhances the efficiency of charging but also protects your devices from any potential damage caused by overcharging.

Constructed with a sleek and sturdy design, the Braun MCA166-USB is not just about functionality; it is also aesthetically pleasing. Its compact size makes it perfect for portability, easily fitting into a pocket or small bag. The durability of the materials used ensures that the charger withstands the rigors of travel while remaining stylish.

Another highlight of the Braun MCA166-USB is its safety features. It incorporates multiple protection mechanisms, including short-circuit prevention and temperature control, ensuring a safe charging environment for your devices.

In summary, the Braun MCA166-USB emerges as an innovative solution for those seeking a reliable charging option. Its robust features, such as dual USB ports, fast charging capabilities, intelligent charging control, and safety measures, make it an ideal choice for anyone looking to stay powered up while balancing a busy lifestyle. With its sleek design and durable construction, the Braun MCA166-USB undoubtedly stands out as a multifaceted charging device for the modern user.