Milwaukee 2291-20 manual Maintenance, Accessories, Five Year Tool Limited Warranty

Page 3
STUD
PLACE ON SURFACE TO CALIBRATE 0.5” DEPTH
PRESS ‘CAL’ TO START
OR ‘STUD’
TO CHANGE DEPTH
STUD
CALIBRATING
0.5” DEPTH

STUD Mode

In Stud mode, the Sub-Scanner will detect wood or metal studs and joists behind wall board, wooden panels, plaster or other non-metallic wall materials. The Sub-Scanner can not reliably detect studs behind material of varying densities. Materials such as carpet, wire metal mesh backing, damp walls, and stucco may affect readings. Alternating surfaces, such as thick grout lines or extremely heavy plaster on drywall, may be detected or show as metal or studs.

1.Turn on the Sub-Scanner. 2.Select Stud mode. 3.Depth of scan is

defaulted to 0.5" (standard wallboard t h i c k n e s s ) . To change the depth of scan (0.5", 1", or 1.5"), press the STUD button.

4.Hold the Sub- Scanner against

the surface and press the Calibrate button.

NOTE: The Sub- Scanner will not

calibrate correctly over studs. To find a location without studs, locate an outlet box and move the Sub-Scanner 6" to either side before beginning

calibration.

 

 

 

5.When SCANNING

 

 

 

STUD

is displayed, move

 

 

the Sub-Scanner

 

SCANNING...

across the surface.

 

Keep

your

free

 

 

hand

and

other

 

0.5” DEPTH

objects at least 6”

 

 

(152 mm) away to

 

 

avoid false readings.

 

NOTE: The Sub-Scanner must remain flat against and in contact with the surface during the entire scan.

6.When a stud is de-

 

STUD

tected, the edge is

 

displayed. Contin-

 

ue moving the Sub-

 

Scanner to detect

EDGE

the entire stud.

 

7.When the center

 

of the stud is de-

 

tected, both arrows

STUD

are displayed.

 

NOTE: If electric

 

MAINTENANCE

WARNING To reduce the risk of injury, always remove the batteries from the tool before performing any maintenance. Never disassemble the tool. Contact a MILWAUKEE service facility for ALL repairs.

Maintaining Tool

Keep your tool in good repair by adopting a regular maintenance program. If the tool does not start or operate at full power with fully charged batter- ies, clean the contacts on the battery. If the tool still does not work properly, return the tool to a MILWAUKEE service facility for repairs.

WARNING To reduce the risk of per- sonal injury and damage, never immerse your tool, battery pack or charger in liquid or allow a liquid to flow inside them.

Cleaning

Clean dust and debris from tool vents. Keep tool handles clean, dry and free of oil or grease. Use only mild soap and a damp cloth to clean the tool since certain cleaning agents and solvents are harmful to plastics and other insulated parts. Some of these include gasoline, turpentine, lacquer thin- ner, paint thinner, chlorinated cleaning solvents, ammonia and household detergents containing ammonia. Never use flammable or combustible solvents around tools.

Repairs

For repairs, return the tool to the nearest service center

listed on the back cover of this operator's manual.

ACCESSORIES

WARNING Always remove battery pack before changing or removing accessories.

Only use accessories specifically recommend- ed for this tool. Others may be hazardous.

For a complete listing of accessories refer to your MILWAUKEE Electric Tool catalog or go online to www.milwaukeetool.com. To obtain a catalog, contact your local distributor or service center.

FIVE YEAR TOOL LIMITED WARRANTY

MILWAUKEE Test & Measurement Product (including bare tool, battery pack(s) and battery charger) is warranted to the original purchaser only to be free from defects in material and workmanship. Subject to certain exceptions, MILWAUKEE will repair or replace any part on this product which, after examination, is determined by MILWAUKEE to be defective in material or workmanship for a period of five (5) years* after the date of purchase. Return of the Test & Measurement tool to the nearest MILWAUKEE Electric Tool Corporation - factory Service Center, freight prepaid and insured is required. A copy of the proof of purchase should be included with the return product. This warranty does not apply to damage that MILWAUKEE determines to be from repairs made or attempted by anyone other than MILWAUKEE authorized personnel, misuse, alterations, abuse, normal wear and tear, lack of maintenance, or accidents.

*The warranty period for the LITHIUM-ION battery pack that ships with Test & Measurement Product is two (2) years from the date of purchase. *Alkaline battery that ships with Test & Measurement Product is separately warranted by the battery manufacture.

*The warranty period for a NON-CONTACT VOLTAGE DETECTOR – 2201 20 or Plumb 2-Beam Plumb Laser – 2230 20 is one (1) year from the date of purchase.

Warranty Registration is not necessary to obtain the applicable warranty on MILWAUKEE product. The manufacturing date of the product will be used to determine the warranty period if no proof of purchase is provided at the time warranty service is requested.

ACCEPTANCE OF THE EXCLUSIVE REPAIR AND REPLACEMENT REMEDIES DESCRIBED HEREIN IS A CONDITION OF THE CONTRACT FOR THE PURCHASE OF EVERY MILWAUKEE PRODUCT. IF YOU DO NOT AGREE TO THIS CONDITION, YOU SHOULD NOT PURCHASE THE PRODUCT. IN NO EVENT SHALL MILWAUKEE BE LIABLE FOR ANY INCIDENTAL, SPECIAL, CONSEQUENTIAL OR PUNITIVE DAMAGES, OR FOR ANY COSTS, ATTORNEY FEES, EXPENSES, LOSSES OR DELAYS ALLEGED TO BE AS A CONSEQUENCE OF ANY DAMAGE TO, FAILURE OF, OR DEFECT IN ANY PRODUCT INCLUDING, BUT NOT LIMITED TO, ANY CLAIMS FOR LOSS OF PROFITS. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES, WRITTEN OR ORAL. TO THE EXTENT PERMITTED BY LAW, MILWAUKEE DISCLAIMS ANY IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR USE OR PURPOSE; TO THE EXTENT SUCH DISCLAIMER IS NOT PERMITTED BY LAW, SUCH IMPLIED WARRANTIES ARE LIMITED TO THE DURATION OF THE APPLICABLE EXPRESS WARRANTY AS DESCRIBED ABOVE. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU, THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.

This warranty applies to product sold in the U.S.A. and Canada only.

LIMITED WARRANTY - MEXICO, CENTRAL AMERICA AND CARIBBEAN

TECHTRONIC INDUSTRIES' warranty is for 5 year since the original purchase date. This warranty card covers any defect in material and workmanship on this Power Tool.

To make this warranty valid, present this warranty card, sealed/stamped by the distributor or store where you purchased the product, to the Authorized Service Center (ASC). Or, if this card has not been sealed/stamped, present the original proof of purchase to the ASC.

Call toll-free 1 800 832 1949 to find the nearest ASC, for service, parts, accessories or components.

Procedure to make this warranty valid

Take the product to the ASC, along with the warranty card sealed/stamped by the distributor or store where you purchased the product, and there any faulty piece or component will be replaced without cost for you. We will cover all freight costs relative with this warranty process.

Exceptions

This warranty is not valid in the following situations:

a)When the product is used in a different manners from the end-user guide or instruction manual.

b)When the conditions of use are not normal.

c)When the product was modified or repaired by people not authorized by TECHTRONIC INDUSTRIES. Note: If cord set is damaged, it should be replaced by an Authorized Service Center to avoid electric risks.

wires or metal/

pipes are in contact

with the backside of

the wallboard, they

may be identified as

a stud.

Model:

Date of Purchase: Distributor or Store Stamp:

SERVICE AND ATTENTION CENTER

Rafael Buelna No.1.

Col. Tezozomoc Mexico, Azcapotzalco D.F.

Ph. 01 800 832 1949

IMPORTED AND COMMERCIALIZED BY: TECHTRONIC INDUSTRIES MEXICO, .S.A. DE C.V. Av. Santa Fe 481 piso 6, Col. Curz Manca.

CP 05349, Cuajimalpa, D.F.

4

5

Image 3
Contents Operators Manual Service Work Area SafetyPersonal Safety Battery USE and CareLimited Warranty MEXICO, Central America and Caribbean MaintenanceAccessories Five Year Tool Limited WarrantyUtilisation ET Entretien ManiementSécurité Individuelle PictographieNettoyage Mode « Stud » MontantAccesoires Entretien de l’outilMantenimiento Seguridad EN EL Área DE TrabajoSeguridad Personal USO Y Cuidado DE LAS Herramientas CON BateríaDescripción Funcional OperacionEnsamblaje Garantía Limitada E.U.A. Y Canadá Accesoriosmantenimiento800.729.3878 Call 1-800-SAWDUST FaxWest Lisbon Road Brookfield, Wisconsin, U.S.A