Philips FW-V520 manual Clock/Timer, View Clock, Clock Setting, Timer Setting

Clock/Timer

E n g l i s h

FW-

STANDBY-ON

	ECO POWER
TITLE/	MP3-CD
BY
DOLALBUM
NAMEB NR
PBC
	V	PRESE		T	NE
	E	ITL
RETURN	P R	T	E		X
					T
	DEMO		PLAY•
	STOP/		PAUSE
	CLEAR
	S
	EA A L BUMING
	RCH • TUN

VCD MINI HIFI SYSTEM

				INTERACTIVE VU METER
DISPLAY PROG	CLOCK•	AUTO	DUBBING REC
	TIMER	REPLAY
		CD 1•2•3	BAND
	VCD		TUNER	MAX
	PAL/			SOUND
	NTSC
			SOURCE	• MAX BASS DYNAMIC AMPLIFICATION
				CONTROL (DAC)
	TAPE		AUX
	TAPE 1•2		CDR / DVD	MIC/
				LEVEL

VOLUME

			I
			AV GATI	ON
			D N		- J
			UN
		O			O
	S					G
				D
					SC
L	E	N	D
IB						V
D		U
E O						A
R R
CR						C
NU
IS
					B
				DB

OSD				2
VCD 123	AUX	TUNER TAPE 1/2
MP3 123
1		2		3
4		5		6
7		8		9
PROG		0	REPEAT
	VOLUME
	ÉÅ
TITLE				TITLE
_	í		ë	+

àÇ á

ALBUM	ALBUM
_	+

View Clock

The clock (if it is set) will be shown in Standby mode.

To view the clock in any source mode (VCD or TUNER for example)

●Press CLOCK•TIMER.

➜The clock will be displayed for a few seconds.

➜If the clock has not been set, "--:--" will be displayed.

Clock Setting

The clock can be set in either 12-hour or

24-hour mode ("AM 12:00" or "00:00" for example)

1Press CLOCK•TIMER twice.

2Press PROG on the system repeatedly to select clock mode.

➜If 12-hour mode is selected, "AM12:00" will start flashing.

➜If 24-hour mode is selected, "00:00" will start flashing.

3Press à or á on the system repeatedly to set the hour.

4Press í or ë on the system repeatedly to set the minute.

5Press CLOCK•TIMER again to store the setting.

➜The clock will start working.

To exit without storing the setting

●Press Çon the system.

Notes:

–The clock setting will be cancelled when the power cord is disconnected or if a power failure occurs.

–During clock setting, if no button is pressed within 90 seconds, the system will exit clock setting mode automatically.

Timer Setting

The system can switch on to VCD,TUNER, or TAPE 2 mode automatically at a preset time, serving as an alarm to wake you up.

IMPORTANT!

–Before setting the timer, ensure that the clock is set correctly.

–The timer will always be switched on after it has been set.

–The timer will not start if a recording is in progress.

–The volume of the timer will increase gradually from the minimum level to the last tuned volume level.

1Press and hold CLOCK•TIMER for more than two seconds to select timer mode.

➜ "AM12:00" or "00:00" or the last timer setting will start flashing.

➜ TIMER will start flashing.

➜ The selected source will be lighted while other available sources are flashing.

2Press VCD, TUNER or TAPE to select the desired source.

28

pg 001-032/V520/21-Eng 28 12/11/01, 5:05 PM 3139 115 21093