![](/images/new-backgrounds/1121442/12144255x1.webp)
1
2
3
4
5
6
7
=================================
Press paper feed to change configuration
SET-UP INSTRUCTIONS
PRESSING THE PAPER FEED BUTTON WHILE THE
GREEN LIGHT IS FLASHING WILL REJECT THE
LAST PRINTED PARAMETER. IF THE BUTTON IS
NOT PRESSED WITHIN 5 SECONDS. THE PARAM-
ETER WILL BE ACCEPTED AND THE NEXT
OPTION WILL BE LISTED.
PRESS THE PAPER FEED BUTTON NOW TO
REJECT THE CURRENT CONFIGURATION AND
CONTINUE WITH THE PRINTER
Printer Control Language
PCL: | ACL Language |
Diag: | Standard Print |
Auto LF: | CR=CR |
Font: |
|
Font: | ACL Language |
Font Quality: | Draft |
Intl Char Set: | USA |
Code Page: | 437 USA |
Receipt LPI: | 6 PLI |
Validation LPI | :6LPI |
RS232 Serial (when used) | |
Baud Rate: | 57.6K |
Data Bits: | 8 Bits |
Stop Bits: | 1 |
Parity: | None |
Flow Control: | Hardware |
Baud Rate Options: |
|
9600 |
|
19.2K |
|
38.4K |
|
57.6K |
|
Baud Rate: | 57.6 |
Baud Rate: | 9600 |
Stop Bit Options: |
|
| |
| |
Stop Bits: | 1 Bit |
Parity Options: |
|
None |
|
Even |
|
Odd |
|
Parity: | None |
Flow Control Options:
Hardware
Software
Flow Control: Hardware
Flow Control: Software
USB (when used) |
|
Descriptor: | Model Number |
Hardware
Mechanism Model:JRNL / VAL
Validation Clamp: Closed
Paper Low Stop: Disabled
Ink Status Reset: Automatic
Document Stop: 1.75 inches
Column Alignment
Half Speed: X
Full Speed: X
Tallies
Printed Lines:
Dot Count:
Validation Opens:
Feed Distance:
Hours On;
Flash Updates:
Cover Opens:
Diagnostic:
0 0 0
Configuration Report to follow
Configuration Example:
Configure the RS232 Serial parameters for the printer using the configuration menu.
| Current Param- | Change to: |
| eters |
|
Baud Rate | 57.6 | 9600 |
Data Bits | 8 | 8 |
Stop Bits | 1 | 1 |
Parity | None | None |
Flow Control | Hardware | Software |
Press and hold the Paper Feed Button and then press the Power Switch to turn the printer on.
Release the Paper Feed Button after 4 seconds for the configu- ration report to begin printing.
1
At the end of the configuration report the printer will prompt “ Press Paper Feed to Change Configuration” .
Press the Paper Feed Button.
2
The Setup instructions will print and prompt to:
“PRESS THE PAPER FEED BUTTON NOW TO REJECT THE CURRENT CONFIGURATION AND CONTINUE WITH THE PRINTER
Press the Paper Feed Button.
3
The First Menu Item will appear “Printer Control Language”. Wait 5 seconds and the next Menu Item will appear “Font”. Wait 5 seconds and the “RS232 Serial (When Used)” Menu will ap- pear.
Press the Paper Feed Button
4
The “Baud Rate Options” will appear
Press the Paper Feed Button
5
The currently selected Baud Rate “57.6K” will appear Press the feed button until the 9600 parameter appears then wait 5 seconds for the next option.
6
The “Stop Bits” parameter will appear
Wait 5 seconds and the next Menu Item will appear “Parity Options”. Wait 5 seconds and the next Menu Item will appear “Flow Control Options”.
Press the Paper Feed Button
7
The currently selected Flow Control Option, “Hardware” will appear
Press the Paper Feed Button until the “Software” parameter appears then wait until the printer goes through the rest of the menus and prints off the configuration Report.
Check the New Report with the old to make sure the setting are now correct.
Pertech Resources Inc. | November 2005 | 220321A | 22 |