Lanner electronic FW-7890 user manual Radio Frequency Emissions Notice, Copyright and Disclaimers

Page 2

Copyright and Disclaimers

© Copyright 2004 - Lanner Electronics Inc.

All Rights Reserved

The contents in this publication have been thoroughly checked and considered accurate. The publisher and manufacturer of this product, Lanner Electronics, is not responsible for any violation of patents or other rights of third parties resulting from its use. Neither does Lanner Electronics assume any responsibility for any inaccuracies contained in this manual, nor make any commitment to keep the information in this document up-to-date.

Lanner reserves the right to make improvements to this document and/or this product at any given time without notice.

No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means (electronic, mechanical, photocopying, recording, or otherwise, without the formal consent from Lanner.

Trademark Acknowledgments

All products and/or brand names stated in this publication are the trademarks of their rightful and associated companies.

Radio Frequency Emissions Notice

This equipment has been tested and found to comply with the digital device limits pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when operate in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area may cause harmful interference, in which case the user will be required to correct the interference at his expense.

ii

Image 2
Contents FW-7890 Series User’s ManualTrademark Acknowledgments Radio Frequency Emissions NoticeCopyright and Disclaimers Federal Communications Commission FCC Statement Safety Instructions Getting Technical Assistance About this ManualTable of Contents LCD Module and Key Pad For FW-7890 P e n d i x E Introduction FeaturesGetting Started Mechanical/ Environmental Form Factor Technical SpecificationsModel Name FW-7890A FW-7890B HumidityPacking Contents MB-X77 System Board Board LayoutJumper Settings and I/O Connector Connector Pin AssignmentsPKMB1PS/2 Keyboard & Mouse Connector 2x4 Header 2.54mm IDEB1 FAN4~6 3 Pin FAN Connector PSC124 Pin ATX Power Connector PCIB1124 Pin Mini PCI Socket CLK RST Ground PSW1For ATX Power Button PCIXA1 184 Pin 3V Pcix Socket FRAME# IRDY# PAR64 PS4S1~24-Pin Power Connector Small-4P LUSBCOM1:BOXHEADER2X202.00DIP VCC3 USBF1:USB Port #1 & #2 Connector 2x5 Pin 2.54mm Face Panel LED Status and Behavior FW-7890 19 2U Rackmount Firewall MechanismsFace Panel Rear View FW-7890 Rear ViewSystem Memory FW-7890 Hardware Installation GuideCPU Installation Installing Compact Flash Card Installing the Mini-PCI CardStarting Setup Award Bios SetupBios Setup Using SetupGetting Help Main MenuNavigating through the menu bar „ Standard Cmos Features Standard Cmos Features Options Description DateIDE Adapters Advanced Bios Features EnabledConfiguration options 9600 / 19200 / 38400 / 57600 Advanced Chipset Features Shadow AreasDram Data Integrity Mode Integrated PeripheralsPrimary Slave Serial ATA Port0 Mode Primary MasterOn-Chip Serial ATA Signal Dual Status LED Power Management Setup Resume by Alarm Suspend ModeHDD Power Down Suspend TypeResource controlled by PnP/PCI ConfigurationReset Configuration Data PCI/VGA Palette SnoopPC Health Status CPU TemperatureSystem Temperature FAN 1 / FAN 2 / FANLoad Optimized Defaults Y/N ? N Load Optimized DefaultsSupervisor/User Password Setting Quit without saving Y/N? Y Save and Exit SetupExit Without Saving Output Specifications Power SupplyPower Supply Specification AC Input Spec FeatureWatchdog Timer Appendix BP e n d i x C Console RedirectionLCD Module and Key Pad For FW-7890 LCM & KeyPad Function Library descriptionPage P e n d i x E LAN Bypass FunctionWarranty Policy Terms and ConditionsRMA Service Request Form Without this form your RMA will be RejectedPEXNSD01-040709 Version 1.0 Printed and published in Taiwan