Printronix ANSI Printer manual Setting Bar Code Parameters, P1 Values, If p1 = Style, UPC a, Upc E

Page 49

Setting Bar Code Parameters

NOTE: If no values are set for parameters p2-p10, the default values will be used. If you have sent a value from the host, this value is active until you replace it or the printer is reset.

In this example the following parameters are changed on Line 10:

p1 = style (Code 128)

p2 = height (3/12 inch)

p9 = human readable font (use special font)

The semicolons are “place holders” for the parameters not being changed.

A list of the 10 parameters and their values follows.

p1

Selects the style.

	Table 17. p1 Values

If p1 =	Style


0	Interleaved 2/5
1	German PTT Interleaved 2 of 5
2	Matrix 2 of 5
3	Industrial 2 of 5
4	Code 3/9
5	EAN-8
6	EAN-13
7	Code 11
8	Reserved
9	Codabar a/t
10	Codabar b/n
11	Codabar c/*
12	Codabar d/e
13	UPC A
14	UPC E

49

Image 49

Contents Programmer’s Reference Manual Page Ansi Printers Trademark Acknowledgements Trademark AcknowledgementsCopyright  1998, 2002 Printronix, Inc Table of Contents Vertical Page Formatting Table of ContentsConversion Tables Glossary Table of Contents About This Manual Software FeaturesRelated Product Information AudienceInstalling Printer Emulations Installing Printer EmulationsDownloading Software Through the Serial or Parallel Port Downloading Software Through the Serial or Parallel PortDebug This is the file you will download into the printer Navigating to the Appropriate Emulation File on the CDCd \downloadEnter Downloading Software Through Network Interface Card NIC This is the file you will download into the NIC Downloading Software Through the Network Interface Card NICPut filename.prgEnter Downloading Optional Font Files to Flash MemoryCopy /b filename.dwn LPT2Enter Downloading Optional Font Files to Flash MemoryCopy /b filename1.dwn+filename2.dwn+...LPT1Enter Flash Memory Message Guide Flash Memory Message GuideMessage Explanation Required Action Error Security PAL Error Program notError Short AT Error Writing toFlash Memory Message Guide Explanation Required Action Installing Printer Emulations Overview Ansi Emulation Default SettingsLPI CPICR = CR CPI Configuring The Ansi Emulation Configuring The Ansi EmulationControl Codes Control Codes DC3 Device Control-3 13HFormat For Control Code Descriptions Format For Control Code Descriptions Escape Control Codes OverviewVertical Formatting Commands Graphics CommandsControl Codes Index Character Sets, International Character Sets, InternationalAscii Code ESC p1 Hex Code 1B 5B p1 Dec Code 27 91 p1 Ansi International Character SetsISO Italian Expanded Mode Expanded ModeAscii Code ESC p1p2 SP B Ascii Code ESC p1p2p3 r Forms Length, Top Margin, Bottom MarginGraphic Rendition Graphic RenditionAscii Code ESC p1p2...pn m Character Types and Enhancements ParameterLine Spacing Margins, Left and Right Margins, Left and RightAscii Code ESC p1p2 s Private Mode, Enable Private Mode, DisableProportional Print Mode Resetting ResettingHardcoded Reset Values Ascii Code ESC c Hex Code Dec CodeSuperscript SubscriptTab, Clear Tab Set, Multiple Horizontal Vertical Position Absolute Terminate Loading of DataVertical Position Relative Dot Patterns And Densities GraphicsDot Patterns And Densities 0X0X0X0 LSB LSB Msbx MSB654321 Graphics Ascii Character Dot Patterns Hex DotsVertical Format Horizontal FormatHorizontal Format Ascii Character Dot Patterns Hex Dots Horizontal Format Byte → Byte n Row ↓Dot Graphics Other Graphics ConsiderationsRepeat Graphics Character Select Graphics Mode Default Bar Code Parameters Setting Bar Code ParametersBar Codes Entering And Exiting Bar CodesP1 Values Setting Bar Code ParametersIf p1 = Style UPC aPostnet Bar Codes P1 ValuesRotation/Font P9 ValuesSpacing Between Bar Codes Human Readable Line HRLBar Code Readers Bar Code ReadersVertical Bar Codes Test ProgramVertical Bar Codes Entering And Exiting Oversize Oversize Character Font OptionOversize Character Font Option Selecting Size Selecting SizeOversize Character Font Option Planning a Vertical Page Format Vertical Page FormattingProprinter And Epson Vertical Tab Table VFU CharacteristicsExecuting Vertical Tabs Vertical Tab PositionsForm Data Form Line Number Vertical Tabs Vertical Tab PositionsStart Load Code 1E or 6E Hex Series EvfuChannel Assignment End Load 1F or 6F HexUsing The Evfu Using The EvfuSeries Evfu Codes PI Line Enabled Data Bits Hex Dec Code ChannelSeries Evfu Codes PI Line Disabled or Not Used Series Evfu Series Evfu Codes PI Line EnabledDLE DC1 DC2 DC3 DC4 NAK SYN ETB Can SUB ESCRelative Line Slewing Clearing The Evfu MemoryData Bits Hex Dec Code Channel End Load Data Bits Lines Hex Dec Code Ansi Evfu Series Evfu Line SlewingDLE DC1 DC2 DC3 DC4 NAK SYN ETB Can SUB ESC Loading the Table Loading the TableAscii Code ESC Hex Code 1B 5D Dec Code 27 93 Two Byte Channel Control Code FormatChannel Control Codes Decimal Value Binary Value Ansi EvfuRemarks CharacterDefault Evfu Table DefaultDescription Ansi Evfu Default Evfu Table Channel Description Skip to Channel CommandDownloading The Evfu Using The PI Line Downloading The Evfu Using The PI LineSkip To Channel Example Program Instruction Remarks Output Ansi Evfu Two Byte Channel Control Code Format Skip to Channel Command Ansi Evfu Standard Ascii Character Set Appendix a 13.3 16.7 Equivalent Columns Conversion Table InchesDecipoints for Column vs. CPI Values Appendix BMargin CPI Column 111 Margin CPI Column Appendix B Margin Column CPI Appendix B Ascii AciaFor example Bold refers to a heavy or thick Character weight, as shown in this sentenceCT+ CPUCTA Cvfu CTSDavfu DCDDTR DSRDvfu EbcdicFifo Ieee HGSIGP LCD LACLED MPLNLQ NackNvfu NvramPCB PALPcba PGLPSA PORRAM ROMSAA RTSSCS SLD SfccSNA SOHTTL TOFUPC UsetOFF 100 Ansi Diagnostics PassedError Occurred / Flushing QUEUES*, 20 ESC Sequence Loading Program from Port XX% Please WAIT... Reset in ProgressSecurity Code Violation 104 Page 164305-001D