Printronix ANSI Printer manual Hgs, Ieee, Igp

Page 91

 

G

GL Characters

Graphic left: Graphic left characters map half of the

 

character set table. The GL characters reside at 0 -

 

127 hex and comprise the ASCII portion of the table.

GR Characters

Graphic right: Graphic right characters map half of

 

the character set table. The GR characters reside at

 

128 - 255 hex and comprise the graphics portion of

 

the table.

 

H

hammer

An assembly consisting of a hammer spring and a

 

hammer tip.

hammer spring

The flat piece of metal, made of spring steel, which

 

supports and pushes the hammer tip.

hammer tip

The small, round point, located near the end of the

 

hammer spring, which strikes the ribbon and leaves a

 

dot on the paper.

hex codes

Based on a numeral system with a radix of 16.

hex dump

A hex dump is a translation of all host interface data

 

to its hexadecimal equivalent. A hex dump is a

 

printer self-test typically used to troubleshoot printer

 

data reception problems.

HGS

Horizontal Grid Size

host computer

The computer that stores, processes, and sends

 

data to be printed, and which communicates directly

 

with the printer. The term “host” indicates the

 

controlling computer, since modern printers are

 

themselves microprocessor-controlled computer

 

systems.

HS

High Speed or Draft Print characters.

HT

Horizontal Tab.

Hz

Hertz. Cycles per second. Frequency.

 

I

IEEE

Institute of Electrical and Electronic Engineers, Inc.

IGP

Intelligent Graphics Processor. An interface that

 

converts graphics commands received from the host

 

computer to binary plot data that is usable by the

 

printer. The IGP is the board-installed Intelligent

 

Graphics Processor. The IGP provides on-line forms,

91

Image 91
Contents Programmer’s Reference Manual Page Ansi Printers Trademark Acknowledgements Trademark AcknowledgementsCopyright  1998, 2002 Printronix, Inc Table of Contents Vertical Page Formatting Table of ContentsConversion Tables Glossary Table of Contents Audience Software FeaturesAbout This Manual Related Product InformationInstalling Printer Emulations Installing Printer EmulationsDownloading Software Through the Serial or Parallel Port Downloading Software Through the Serial or Parallel PortDebug This is the file you will download into the printer Navigating to the Appropriate Emulation File on the CDCd \downloadEnter Downloading Software Through Network Interface Card NIC This is the file you will download into the NIC Downloading Software Through the Network Interface Card NICPut filename.prgEnter Downloading Optional Font Files to Flash MemoryCopy /b filename.dwn LPT2Enter Downloading Optional Font Files to Flash MemoryCopy /b filename1.dwn+filename2.dwn+...LPT1Enter Flash Memory Message Guide Flash Memory Message GuideMessage Explanation Required Action Error Writing to Error Program notError Security PAL Error Short ATFlash Memory Message Guide Explanation Required Action Installing Printer Emulations Overview Ansi Emulation Default SettingsLPI CPICR = CR CPI Configuring The Ansi Emulation Configuring The Ansi EmulationControl Codes Control Codes DC3 Device Control-3 13HFormat For Control Code Descriptions Format For Control Code Descriptions Escape Control Codes OverviewVertical Formatting Commands Graphics CommandsControl Codes Index Ansi International Character Sets Character Sets, InternationalCharacter Sets, International Ascii Code ESC p1 Hex Code 1B 5B p1 Dec Code 27 91 p1ISO Italian Expanded Mode Expanded ModeAscii Code ESC p1p2 SP B Ascii Code ESC p1p2p3 r Forms Length, Top Margin, Bottom MarginCharacter Types and Enhancements Parameter Graphic RenditionGraphic Rendition Ascii Code ESC p1p2...pn mLine Spacing Margins, Left and Right Margins, Left and RightAscii Code ESC p1p2 s Private Mode, Enable Private Mode, DisableProportional Print Mode Ascii Code ESC c Hex Code Dec Code ResettingResetting Hardcoded Reset ValuesSuperscript SubscriptTab, Clear Tab Set, Multiple Horizontal Vertical Position Absolute Terminate Loading of DataVertical Position Relative 0X0X0X0 LSB LSB Msbx MSB GraphicsDot Patterns And Densities Dot Patterns And Densities654321 Graphics Ascii Character Dot Patterns Hex DotsHorizontal Format Byte → Byte n Row ↓ Horizontal FormatVertical Format Horizontal Format Ascii Character Dot Patterns Hex DotsDot Graphics Other Graphics ConsiderationsRepeat Graphics Character Select Graphics Mode Entering And Exiting Bar Codes Setting Bar Code ParametersDefault Bar Code Parameters Bar CodesUPC a Setting Bar Code ParametersP1 Values If p1 = StylePostnet Bar Codes P1 ValuesRotation/Font P9 ValuesSpacing Between Bar Codes Human Readable Line HRLBar Code Readers Bar Code ReadersVertical Bar Codes Test ProgramVertical Bar Codes Entering And Exiting Oversize Oversize Character Font OptionOversize Character Font Option Selecting Size Selecting SizeOversize Character Font Option Planning a Vertical Page Format Vertical Page FormattingVertical Tab Positions VFU CharacteristicsProprinter And Epson Vertical Tab Table Executing Vertical TabsForm Data Form Line Number Vertical Tabs Vertical Tab PositionsEnd Load 1F or 6F Hex Series EvfuStart Load Code 1E or 6E Hex Channel AssignmentData Bits Hex Dec Code Channel Using The EvfuUsing The Evfu Series Evfu Codes PI Line EnabledDC1 DC2 DC3 DC4 NAK SYN ETB Can SUB ESC Series Evfu Series Evfu Codes PI Line EnabledSeries Evfu Codes PI Line Disabled or Not Used DLERelative Line Slewing Clearing The Evfu MemoryData Bits Hex Dec Code Channel End Load Data Bits Lines Hex Dec Code Ansi Evfu Series Evfu Line SlewingDLE DC1 DC2 DC3 DC4 NAK SYN ETB Can SUB ESC Two Byte Channel Control Code Format Loading the TableLoading the Table Ascii Code ESC Hex Code 1B 5D Dec Code 27 93Character Ansi EvfuChannel Control Codes Decimal Value Binary Value RemarksDefault Evfu Table DefaultDescription Ansi Evfu Default Evfu Table Channel Description Skip to Channel CommandDownloading The Evfu Using The PI Line Downloading The Evfu Using The PI LineSkip To Channel Example Program Instruction Remarks Output Ansi Evfu Two Byte Channel Control Code Format Skip to Channel Command Ansi Evfu Standard Ascii Character Set Appendix a 13.3 16.7 Equivalent Columns Conversion Table InchesDecipoints for Column vs. CPI Values Appendix BMargin CPI Column 111 Margin CPI Column Appendix B Margin Column CPI Appendix B Ascii AciaFor example Bold refers to a heavy or thick Character weight, as shown in this sentenceCT+ CPUCTA DCD CTSCvfu DavfuEbcdic DSRDTR DvfuFifo Ieee HGSIGP MPL LACLCD LEDNvram NackNLQ NvfuPGL PALPCB PcbaROM PORPSA RAMSAA RTSSCS SOH SfccSLD SNAUset TOFTTL UPCOFF 100 Ansi Diagnostics PassedError Occurred / Flushing QUEUES*, 20 ESC Sequence Loading Program from Port XX% Please WAIT... Reset in ProgressSecurity Code Violation 104 Page 164305-001D