Printek FormsPro 4300 Option Switches When Configured for Coaxial Operation, CX/TX Interface

Page 60

Optional Coaxial/Twinaxial Interface

In the DSC/DSE type LU3 mode, both formatted and unformatted data streams are supported.

Interface diagnostics are available at the end of this appendix in the section titled “Coaxial/Twinaxial Interface Diagnostics”.

CX/TX Interface.

Option Switches When Configured for Coaxial Operation

The dipswitches as shown above have the following meanings when the interface is configured for coaxial operation. An asterisk (*) indicates the factory default setting.

Switch/Position

Function

SW1-1 OFF*

Select IBM 3287 Emulation.

SW1-1 ON

Select IBM 3262 Emulation.

SW1-2 OFF*

Reserved for future use.

SW1-3 OFF*

Reserved for factory use.

SW1-4 OFF*

Reserved for factory use.

SW1-5 OFF*

Set default Maximum Print Position to 132

 

 

columns.

SW1-5 ON

Set default Maximum Print Position to none.

SW1-6 OFF*

Set default Maximum Print Line to none.

SW1-6 ON

Set default Maximum Print Line to 66 lines.

SW1-7 SW1-8

Parallel multiplexer timeout.

OFF*

OFF*

Short (15 seconds)

ON

OFF

Medium.

Page C-2

Page 59 Page 61
Image 60
Page 59 Page 61
Contents FormsPro 4300, FormsPro Serial Matrix PrintersPage Table of Contents Appendix F Control Code & Escape Sequence Summaries HOW to USE this Manual IntroductionPrinter Model Descriptions KEY Features Installation and Quick Setup Selecting AN Appropriate Installation LocationInstallation and Quick Setup Installing the Ribbon Ribbon Cartridge Installation Lowering closing Ribbon Loading BailInstalling Paper Opening Latch PanelFormsPro 4503 With Form Installed Front Tractors Installation and Quick Setup Testing the Printer Connecting the Printer to a ComputerEntering the Interface Menu AT the Control Panel Parallel Interface Connector Parallel InterfaceRS-232C Serial Interface Connector Matching the Printer to Your Application SoftwareRS-232C Serial Interface Selecting Ansi X3.64 Emulation Selecting Epson EmulationSelecting Proprinter Emulation Selecting DEC LA 120-RA Emulation Selecting TTY EmulationSelecting Printek Emulation Page Control Panel Operation and Setup Menus Control Panel Display and IndicatorsOperation IntroductionOperation Control Panel Buttons Load / Form FeedAlign UP This button enters and exits the setup menus that are Introduction to Setup Entering the Forms Setup Menu# CPI Operation FX DF Entering the Interface Setup Menu DTR Operation Changing the Paper Changing the Form in the TractorsOpening The Latch Panel FormsPro 4503 With Forms Installed Front Tractor Path FormsPro 4503 Changing to a Form Installed in Another Path Using Printek Ribbons Changing the RibbonRemoving the Old Ribbon Installing the New Ribbon Lowering closing Ribbon Loading Bail Using Special Features Unloading and Selecting FormsHandling a Paper Error Condition Standard Paper Error HandlingHandling Paper Errors With Page Reprint Enabled Using the Ribbon Check Feature Checking Setup ConfigurationMatching the Ribbon Wear Indicator to Printer Use Turning Off Ribbon CheckingPrinting Setup Information Parking the Formspro 4503 Tractors for ShipmentPage Symptoms and Possible Causes Case of DifficultyCase of Difficulty Case of Difficulty Using the HEX Dump Mode Replacing the AC Power Fuse Selecting a Quality FormPrinter is now ready to be put back into service Advanced Control Panel Features Setup OptionsAppendix a Advanced Control Panel Features Advanced Control Panel Features Setup Security Advanced Control Panel Features A-6 RS-422 Serial Interface Connector Appendix B Optional RS-422 Interface Page Appendix C Optional COAXIAL/TWINAXIAL InterfaceCoaxial Operation Option Switches When Configured for Coaxial Operation CX/TX InterfaceLong Twinaxial Operation Option Switches When Configured for Twinaxial Operation Twinaxial Address SwitchTwinaxial Installation Preparation Getting On-lineTwinaxial Verification Problems COAXIAL/TWINAXIAL Interface Diagnostics Code Dump Mode Address 0 through Configuration Printout AddressC-10 Appendix D Optional Buffer ExpansionElectronics Cover Screws Buffer and Jumper Locations on Main Circuit BoardOptional Buffer Expansion Page Appendix E Ascii Character TablesAscii Character Tables PC Fast Draft PC Draft PC Letter Quality E-3 Ebcdic Fast Draft Ebcdic Draft Ebcdic Letter Quality E-4 Ascii Character Tables OCR a OCR B DECIMAL-TO-OCTAL-TO-HEXADECIMAL-TO-ASCII Conversion Table Oct Hex Ascii DecPage Appendix F Control Code and Escape Sequence SummariesAnsi x3.64 Emulation Epson FX Emulation ESC * m n1 n2 dataF-3 IBM Proprinter Emulation ESC @ n1 n2 m1 m2 m3 m4LA-120 Emulation Simple TTY Emulation Printek Emulation ESC CPage Printer Reset Conditions Appendix GPage Cloning Printer Setup Appendix HCloning from Printer to Printer Using a Setup Unit for Cloning Possible Cloning ErrorsInformation that is Cloned Cloning from a Printer to a Setup Unit Cloning from a Setup Unit to a PrinterCloning Printer Setup Printer Specifications AppendixLine Spacing Computer Interface Reliability Specifications subject to change without notice Page Setup Menu Summaries Appendix JSetup Interface Glossary AsciiGlossary Glossary-1
Top Page Image Contents