Printek FormsPro 4300, 4500, 4503 operation manual Twinaxial Operation

Page 62

Optional Coaxial/Twinaxial Interface

TWINAXIAL OPERATION

When you attach devices such as the FormsPro 4000 series printer to the System 3X, the devices must be configured onto the system by device type, so that they may be supported and used to their utmost ability. Once a device has been configured onto the system, the system utilizes the device type information to communicate with the device. The device responds to the system's polls and commands in accordance to its device description. The system being configured for a 4214 Model 01 printer, for example, as address 10 (port 1, device 0) will expect a response from a 4214 Model 01 at that address location. Should there be a 5256 Model 3 printer at device address 10 when the system sends a print job to the printer, the system would generate a “HARDWARE FAILURE” error message (for System

38)or a “PROGRAM ERROR” error message (for Systems 34/36). It is very important to observe the device and System 3X configurations.

The FormsPro 4000 series printers may emulate three different IBM models as listed in the following table. The DIP switches allow you to select these emulations. As shipped from the factory, the printer is set for 4214 Model 2 emulation.

CX/TX Interface.

Page C-4

Page 61 Page 63
Image 62
Page 61 Page 63
Contents FormsPro 4300, FormsPro Serial Matrix PrintersPage Table of Contents Appendix F Control Code & Escape Sequence Summaries HOW to USE this Manual IntroductionPrinter Model Descriptions KEY Features Installation and Quick Setup Selecting AN Appropriate Installation LocationInstallation and Quick Setup Installing the Ribbon Ribbon Cartridge Installation Lowering closing Ribbon Loading BailInstalling Paper Opening Latch PanelFormsPro 4503 With Form Installed Front Tractors Installation and Quick Setup Testing the Printer Connecting the Printer to a ComputerEntering the Interface Menu AT the Control Panel Parallel Interface Connector Parallel InterfaceRS-232C Serial Interface RS-232C Serial Interface ConnectorMatching the Printer to Your Application Software Selecting Proprinter Emulation Selecting Ansi X3.64 EmulationSelecting Epson Emulation Selecting Printek Emulation Selecting DEC LA 120-RA EmulationSelecting TTY Emulation Page Operation Control Panel Operation and Setup MenusControl Panel Display and Indicators IntroductionOperation Control Panel Buttons Load / Form FeedAlign UP This button enters and exits the setup menus that are Introduction to Setup Entering the Forms Setup Menu# CPI Operation FX DF Entering the Interface Setup Menu DTR Operation Opening The Latch Panel Changing the PaperChanging the Form in the Tractors FormsPro 4503 With Forms Installed Front Tractor Path FormsPro 4503 Changing to a Form Installed in Another Path Removing the Old Ribbon Using Printek RibbonsChanging the Ribbon Installing the New Ribbon Lowering closing Ribbon Loading Bail Using Special Features Unloading and Selecting FormsHandling a Paper Error Condition Standard Paper Error HandlingHandling Paper Errors With Page Reprint Enabled Matching the Ribbon Wear Indicator to Printer Use Using the Ribbon Check FeatureChecking Setup Configuration Turning Off Ribbon CheckingPrinting Setup Information Parking the Formspro 4503 Tractors for ShipmentPage Symptoms and Possible Causes Case of DifficultyCase of Difficulty Case of Difficulty Using the HEX Dump Mode Replacing the AC Power Fuse Selecting a Quality FormPrinter is now ready to be put back into service Appendix a Advanced Control Panel FeaturesSetup Options Advanced Control Panel Features Advanced Control Panel Features Setup Security Advanced Control Panel Features A-6 Optional RS-422 Interface RS-422 Serial Interface ConnectorAppendix B Page Coaxial Operation Appendix COptional COAXIAL/TWINAXIAL Interface Option Switches When Configured for Coaxial Operation CX/TX InterfaceLong Twinaxial Operation Option Switches When Configured for Twinaxial Operation Twinaxial Address SwitchTwinaxial Installation Preparation Getting On-lineTwinaxial Verification Problems COAXIAL/TWINAXIAL Interface Diagnostics Code Dump Mode Address 0 through Configuration Printout AddressC-10 Appendix D Optional Buffer ExpansionElectronics Cover Screws Buffer and Jumper Locations on Main Circuit BoardOptional Buffer Expansion Page Appendix E Ascii Character TablesAscii Character Tables PC Fast Draft PC Draft PC Letter Quality E-3 Ebcdic Fast Draft Ebcdic Draft Ebcdic Letter Quality E-4 Ascii Character Tables OCR a OCR B DECIMAL-TO-OCTAL-TO-HEXADECIMAL-TO-ASCII Conversion Table Oct Hex Ascii DecPage Ansi x3.64 Emulation Appendix FControl Code and Escape Sequence Summaries Epson FX Emulation ESC * m n1 n2 dataF-3 IBM Proprinter Emulation ESC @ n1 n2 m1 m2 m3 m4LA-120 Emulation Simple TTY Emulation Printek Emulation ESC CPage Printer Reset Conditions Appendix GPage Cloning from Printer to Printer Cloning Printer SetupAppendix H Information that is Cloned Using a Setup Unit for CloningPossible Cloning Errors Cloning from a Printer to a Setup Unit Cloning from a Setup Unit to a PrinterCloning Printer Setup Printer Specifications AppendixLine Spacing Computer Interface Reliability Specifications subject to change without notice Page Setup Menu Summaries Appendix JSetup Interface Glossary AsciiGlossary Glossary-1

4500, 4503, FormsPro 4300 specifications

Printek FormsPro 4300, 4500, and 4503 are high-performance printers designed to meet the demands of businesses that require high-quality, reliable printing for forms and transactional documents. These models are well-regarded for their durability, ease of use, and advanced features tailored to enhance productivity in various work environments.

One of the key features of the FormsPro series is its robust printing technology. Utilizing impact dot matrix printing, these printers can produce clear and sharp text as well as graphics on multipart forms, making them ideal for applications such as invoicing, receipts, and shipping documents. The FormsPro 4300 offers a print speed of up to 550 characters per second, while the 4500 and 4503 models offer even higher speeds, enabling businesses to streamline their operations and reduce wait times.

Another important characteristic of these printers is their ability to handle a wide range of paper types and sizes. The FormsPro series supports continuous forms, single sheets, and labels, accommodating various printing needs. The adjustable paper feed allows for easy handling of different materials, ensuring that users can seamlessly print on standard forms or custom configurations.

In addition to versatility, the FormsPro printers boast user-friendly features such as an intuitive control panel and easy connectivity options. They are equipped with USB and parallel interfaces, allowing for easy integration with existing systems. This makes setup and operation straightforward, even for those who may not be tech-savvy.

Durability is also a hallmark of the Printek FormsPro series. Built with high-quality components, these printers are designed to withstand the rigors of daily use in busy environments. They feature a durable print head and are engineered to minimize maintenance costs, making them a smart investment for businesses.

Furthermore, the FormsPro 4500 and 4503 models come with enhanced memory options, allowing for faster processing of larger print jobs. This improvement translates to reduced processing time, which is critical for businesses that rely on efficiency and quick turnaround.

In conclusion, the Printek FormsPro 4300, 4500, and 4503 printers represent an excellent choice for businesses requiring reliable and efficient printing solutions. With their robust performance, versatility, and durability, these printers are designed to meet the diverse needs of modern enterprises, making them a valuable addition to any office setting.
Top Page Image Contents