Topcom WBR 7101GMR Parameters Default Description, IP Subnet Mask, 802.1d Spanning Tree Disabled

Page 39

2.3 LAN

The LAN Port screen below allows you to specify a private IP address for your router’s LAN ports as well as a subnet mask for your LAN segment.

Parameters

Default

Description

 

 

 

LAN IP

 

 

IP address

192.168.1.1

This is the router’s LAN port IP address (Your

 

 

LAN clients default gateway IP address)

IP Subnet Mask

255.255.255.0

Specify a Subnet Mask for your LAN segment

802.1d Spanning Tree Disabled

If 802.1d Spanning Tree function is enabled, this

 

 

router will use the spanning tree protocol to

 

 

prevent from network loop happened in the LAN

 

 

ports.

DHCP Server

Enabled

You can enable or disable the DHCP server. By

 

 

enabling the DHCP server the router will

 

 

automatically give your LAN clients an IP

 

 

address. If the DHCP is not enabled then you’ll

have to manually set your LAN client’s IP addresses; make sure the LAN Client is in the same subnet as this broadband router if you

39

Page 38 Page 40
Image 39
Page 38 Page 40
Contents Skyr@cer WBR 7101gmr Get to know the Broadband Router Setup DiagramIntroduction Minimum RequirementsAppendix a Glossary Package Content FeaturesWide Area Network WAN ResetGet to know the Broadband Router Back Panel Local Area Network LANOff Front PanelLight Status Description WAN 10/100MBelow shows a typical setup for a Local Area Network LAN 2a Windows 95/98/Me Configure your PC to obtain an IP address automaticallyDNS Configuration Select Disable DNS Getting started2b Windows XP 2c Windows 2d Windows NT IP Address Select Obtain an IP address from a Dhcp server Quick Setup Wizard Chapter Status Information Chapter Quick Setup Wizard ChapterGeneral Setup Chapter Menu DescriptionLogout Tools ChapterEnable Daylight Savings Time Server AddressEnd Daylight Savings Time Click on Next to proceed to the next page Broadband Type MAC Address Parameters Description Host NameParameters Description Gateway IPSubnet Mask Password Service NameParameter Description User Name Interface. The WAN connection will not disconnected due When you click Connect manually from the Web userTo the idle timeout. If the WAN line breaks down and latter If you select Manual, the router will connect to ISP onlyUser ID GatewayBezeq in Israel Select this item if you are using the service provided byPptp Gateway Connection ID This is the ID given by ISP. This is optionalL2TP L2TP Gateway Router When YOU Finished Using the InternetPage Enter the User Name provided by your ISP for the Telstra Big Menu Description System WANLAN Firewall System End Daylight Savings Time New Password Parameters Description Current PasswordPort Port number of remote management web interface Parameters Description Host AddressEnabled Your ISP has given you an IP address already Dynamic IP Secondary DNS Address optional Parameters Description Domain Name Server DNS ServerDomain name Parameters Default Description Enable/DisablePassword/Key ProviderDhcp Server Parameters Default Description802.1d Spanning Tree Disabled IP Subnet MaskLease Time IP Address PoolTo End IP 192.168.1.199. If you Wireless module Function AP Mode setting AP Bridge-Point to Point mode setting AP Bridge-Point to Multi-Point mode setting Band Parameters Default Description ModePage Fragment Threshold specifies the maximum CTS Protection Data RatePreamble Type Broadcast EssidKey Format Ascii Characters guest 3.2 802.1x only 3.3 802.1x WEP Static key Wpatkip Page WPA Radius QoS Page Edit QoS Rule Parameters Description Rule NameBandwidth Remote IP Address ResetLocal IP Address Local Port RangeUPnP Setting Parameter Description Port ForwardingVirtual Server Static Routing ALG SettingParameter Description Enable Port Forwarding It and want to retype again, just click Clear Parameters Description Enable Virtual Server Private IP Private PortType Address host in your LAN Example Virtual Server Special Applications Comment Description of this setting Example Special ApplicationsExample Page UPnP Settings ALG Settings Static Routing Page 4 DMZ Parameters Description Access ControlFill IP Filtering Table to filter PC clients by IP Filter client PCs by IPPage Add PC Page Example Access Control URL Blocking Port Scan Intrusion Detection FeaturePing of Death Discard Ping From WANParameters Description Enable DMZ Enable/disable DMZ Public IP AddressClient PC IP Address Security Log ParametersDescriptionDevice Status System LogParameters Description Information Primary DNS and Secondary DNS being used Parameters Description Internet ConnectionParameters Description Device Status Parameters Description System Log Parameters Description Security Log Parameters Description Active Dhcp Client Statistics You can reset the router’s system should any problem exist Parameters Description Configuration Tools Parameters Description Firmware Upgrade Parameters Description Reset ResetAppendix a How to Manually find your PC’s IP and MAC addressGlossary TCP FTP Smtp POP3
Top Page Image Contents