Topcom WBR 7101GMR manual Fragment Threshold specifies the maximum

Page 47

2.4.2 Advanced Settings

You can set advanced wireless LAN parameters of this router. The parameters include Authentication Type, Fragment Threshold, RTS Threshold, Beacon Interval, Preamble Type …… You should not change these parameters unless you know what effect the

changes will have on this router.

Parameters

Default

Description

 

 

 

Fragment Threshold

 

"Fragment Threshold" specifies the maximum

 

 

size of packet during the fragmentation of data

 

 

to be transmitted. If you set this value too low, it

 

 

will result in bad performance.

RTS Threshold

 

When the packet size is smaller the RTS

 

 

threshold, the wireless router will not use the

 

 

RTS/CTS mechanism to send this packet.

Beacon Interval

 

The interval of time that this wireless router

 

 

broadcast a beacon. Beacon is used to

 

 

synchronize the wireless network.

DTIM Period

 

The DTIM period you specify here indicates

 

 

how often the clients served by this access

 

 

point should check for buffered data still on

 

 

the AP awaiting pickup.

 

 

 

47

Image 47
Contents Skyr@cer WBR 7101gmr Get to know the Broadband Router Setup DiagramIntroduction Minimum RequirementsAppendix a Glossary Package Content FeaturesWide Area Network WAN ResetGet to know the Broadband Router Back Panel Local Area Network LANOff Front PanelLight Status Description WAN 10/100MBelow shows a typical setup for a Local Area Network LAN 2a Windows 95/98/Me Configure your PC to obtain an IP address automaticallyDNS Configuration Select Disable DNS Getting started2b Windows XP 2c Windows 2d Windows NT IP Address Select Obtain an IP address from a Dhcp server Quick Setup Wizard Chapter Status Information Chapter Quick Setup Wizard ChapterGeneral Setup Chapter Menu DescriptionLogout Tools ChapterEnd Daylight Savings Time Enable Daylight SavingsTime Server Address Click on Next to proceed to the next page Broadband Type MAC Address Parameters Description Host NameSubnet Mask Parameters DescriptionGateway IP Parameter Description User Name PasswordService Name Interface. The WAN connection will not disconnected due When you click Connect manually from the Web userTo the idle timeout. If the WAN line breaks down and latter If you select Manual, the router will connect to ISP onlyUser ID GatewayBezeq in Israel Select this item if you are using the service provided byPptp Gateway Connection ID This is the ID given by ISP. This is optionalL2TP L2TP Gateway Router When YOU Finished Using the InternetPage Enter the User Name provided by your ISP for the Telstra Big LAN Menu Description SystemWAN Firewall System End Daylight Savings Time New Password Parameters Description Current PasswordPort Port number of remote management web interface Parameters Description Host AddressEnabled Your ISP has given you an IP address already Dynamic IP Secondary DNS Address optional Parameters Description Domain Name Server DNS ServerDomain name Parameters Default Description Enable/DisablePassword/Key ProviderDhcp Server Parameters Default Description802.1d Spanning Tree Disabled IP Subnet MaskTo End IP 192.168.1.199. If you Lease TimeIP Address Pool Wireless module Function AP Mode setting AP Bridge-Point to Point mode setting AP Bridge-Point to Multi-Point mode setting Band Parameters Default Description ModePage Fragment Threshold specifies the maximum CTS Protection Data RatePreamble Type Broadcast EssidKey Format Ascii Characters guest 3.2 802.1x only 3.3 802.1x WEP Static key Wpatkip Page WPA Radius QoS Page Bandwidth Edit QoS RuleParameters Description Rule Name Remote IP Address ResetLocal IP Address Local Port RangeVirtual Server UPnP SettingParameter Description Port Forwarding Static Routing ALG SettingParameter Description Enable Port Forwarding It and want to retype again, just click Clear Type Parameters Description Enable Virtual Server Private IPPrivate Port Address host in your LAN Example Virtual Server Special Applications Example Comment Description of this settingExample Special Applications Page UPnP Settings ALG Settings Static Routing Page 4 DMZ Parameters Description Access ControlFill IP Filtering Table to filter PC clients by IP Filter client PCs by IPPage Add PC Page Example Access Control URL Blocking Port Scan Intrusion Detection FeaturePing of Death Discard Ping From WANClient PC IP Address Parameters Description Enable DMZ Enable/disable DMZPublic IP Address Security Log ParametersDescriptionDevice Status System LogParameters Description Information Primary DNS and Secondary DNS being used Parameters Description Internet ConnectionParameters Description Device Status Parameters Description System Log Parameters Description Security Log Parameters Description Active Dhcp Client Statistics You can reset the router’s system should any problem exist Parameters Description Configuration Tools Parameters Description Firmware Upgrade Parameters Description Reset ResetAppendix a How to Manually find your PC’s IP and MAC addressGlossary TCP FTP Smtp POP3