Silicon Image SSD-C08G(I)-3150 manual Standby 96h, E2h

Page 91

ATA COMMAND BLOCK AND SET DESCRIPTION

SSD-CXXX(I)-3150 DATA SHEET

Standby — 96h, E2h

When the Standby command is issued by the host, it transitions the device into standby mode. If the Sector Count register is set to a value other than 0h, the Auto Powerdown function is enabled and the device returns to Idle mode.

Table 68: Standby — 96h, E2h

Register	D7	D6		D5	D4		D3	D2	D1	D0
Feature						X

Sector Count			Timer Count (5ms x Timer Count)

Sector Number						X

Cylinder Low						X

Cylinder High						X

Drive Head	X	X		X	Drive			X

Command					96h or E2h

SILICONSYSTEMS PROPRIETARY

This document and the information contained within it is confidential and proprietary to SiliconSystems, Inc.

All unauthorized use and/or reproduction is prohibited.

3150C-10DSR

PAGE 81

FEBRUARY 2, 2009

Image 91

Contents Overview FeaturesSisecure Revision History SSD-CXXXI-3150 Data SheetTable of Contents ATA and True IDE Register Decoding Attribute Memory Description and OperationCommon Memory Description and Operation Space Description and OperationATA Command Set Nomenclature Part Numbers Sample Label List of Figures List of Tables SSD-CXXXI-3150 Data Sheet Part Numbering Nomenclature Physical Dimensions Physical SpecificationsSystem Power Requirements Product SpecificationsSystem Performance Reliability SiliconDrive Part# Capacity Service Life GB Written per DayOperational Life Span Environmental Specifications Product Capacity SpecificationsProduct Capacity Number Bytes Sectors Cylinders Heads Track Pin Assignments Electrical SpecificationSignal Name Pin Type Description Signal DescriptionsDasp SpkrInpack CselGround True IDE modeDmarq GNDIowr This signal is not used in this mode PC Card memory ModeIord IordRDY/-BSY ATA SELIreq Dmack Reset+5V, +3.3V power PC Card memory Mode REGIordy This signal is the same for all modes PC Card I/O ModeVoltage Sense Signals WaitIOIS16 Symbol Parameter Minimum Maximum UnitsAbsolute Maximum Ratings Capacitance Symbol Parameter Maximum UnitsDC Characteristics Symbol Parameter V ±10% 5V ±10% Units Minimum MaximumAttribute and Common Memory Read Timing Attribute and Common Memory Read TimingAttribute and Common Memory Write Timing Attribute and Common Memory Write TimingO Access Read Timing Access Read TimingO Access Write Timing Access Write TimingTrue IDE Read/Write Access Timing True IDE Read/Write Access TimingTrue IDE Multiword DMA Read/Write Access Timing True IDE Multiword DMA Read/Write Access TimingFunction REG# CE1# CE2# D158 D70 ModeAttribute Memory Description and Operation Attribute Memory Read OperationsAttribute Memory Write Operations Register Operation Addr CE1# Attribute Memory MapREG# WE# OE# Card Information Structure Attribute Data Description of Contents CIS Function OffsetCistplfunce Tpcemi Tpcefs Tpceio Exponent Nominal voltage = VCC nominal value A6h 1Eh IRQ Configuration table entry tuple Tuple code E4h 12h Exponent Nominal voltage = VCC nominal value F0h 4Dh Siliconsystems Proprietary Card Information Structure Sreset Configuration Option Register 200hBits Description Read Changed SigChg IOis8 PwrDn Int Write Default Value Configuration and Status Register 202hCrdy Pin Placement Register 204hRrdy RFU Copy Number Socket Number Default ValueSocket and Copy Register 206h Read/WriteCommon Memory Write Operations Common Memory Description and OperationCommon Memory Read Operations REG#O Space Write Operations Function Mode REG# CE1# CE2# A0 IORD# IOWR# D158 D70Space Description and Operation O Space Read OperationsMemory-Mapped Register Decoding ATA and True IDE Register DecodingReg# Offset A10 A9A4 OE# = L WE# = L Independent I/O Mode Register Decoding Primary Secondary Primary and Secondary I/O Mapped Register DecodingReg# A10 A9A4 IORD# = L IOWR# = LCS0# CS1# DA02 DA01 DA00 Task File Register SpecificationDIOR# = L DIOW# = L Media Changed MC. Set to Error RegisterTrack 0 Not Found TKONF. Set when the execute drive ATA RegistersByte Feature RegisterOperation Read/WriteSector Count Register Read/Write Sector Count Default ValueLogical Block Number bits A07-A00 LBA Addressing Sector Number RegisterLogical Block Number bits A15-A08 LBA Addressing Cylinder Low RegisterLogical Block Number bits A23-A16 LBA Addressing Cylinder High RegisterHS3 HS2 HS1 HS0 Drive/Head RegisterLBA27 LBA26 LBA25 LBA24 DRQ Corr IDX ERR Drive Write Fault DWF. Always set toStatus Register BSY DrdyOperation Read/Write ATA Command Code Command RegisterAlternate Status Register NIEN Bits Description Device Control RegisterOperation Write SrstDevice Address Register Read/Write NWTG NHS3 NHS2 NHS1 NHS0 NDS1 NDS0 Default ValueClass Command Name Registers Used Code ATA Command Block and SET DescriptionATA Command Block and Set Description ATA Command SetATA Command Set Check Power Mode 98h, E5h Check Power Mode 98h, E5hRegister Executive Drive Diagnostic 90h Executive Drive Diagnostic 90hFormat Track 50h Drive Head Number LBA27-24 Command 50hFormat Track 50h Identify Drive ECh Identify Drive EChID bit in IDE Word Data Default Bytes Data Description AddressIdentify Drive Drive Attribute Data 044Ah fixedWord Data Default Bytes Data Description Address Identify Drive Drive Attribute Data Idle 97h, E3h Idle 97h, E3hIdle Immediate 95h, E1h Idle Immediate 95h, E1hInitialize Drive Parameters 91h Initialize Drive Parameters 91hRecalibrate 1Xh Drive Command 1XhRecalibrate 1Xh Read Buffer E4h Read Buffer E4hLBA Drive Head Number LBA27-24 Command C8hRead DMA C8h Read DMA C8hRead Multiple C4h Drive Head Number LBA27-24 Command C4hRead Multiple C4h Read Sector 20h, 21h Drive Head Number LBA27-24 Command 20h or 21hRead Sector 20h, 21h Read Long Sectors 22h, 23h Drive Head Number LBA27-24 Command 22h or 23hRead Long Sectors 22h, 23h Read Verify Sectors 40h, 41h Drive Head Number LBA27-24 Command 40h or 41hRead Verify Sectors 40h, 41h Seek 7Xh Drive Head Number LBA27-24 Command 7XhSeek 7Xh Feature Operation Set Features EFhSet Features EFh Set Features’ AttributesSet Multiple Mode C6h Set Multiple Mode C6hSet Sleep Mode 99h, E6h Set Sleep Mode 99h, E6hStandby 96h, E2h Standby 96h, E2hStandby Immediate 94h, E0h Standby Immediate 94h, E0hWrite Buffer E8h Write Buffer E8hWrite DMA CAh Drive Head NumberLBA27-24 Command CAhWrite DMA CAh Write Multiple C5h Drive Head NumberLBA27-24 Command C5hWrite Multiple C5h Write Sectors 30h, 31h Drive Head Number LBA27-24 Command 30h or 31hWrite Sectors 30h, 31h Write Long Sectors 32h, 33h Drive Head Number LBA27-24 Command 32h or 33hWrite Long Sectors 32h, 33h Erase Sectors C0h Drive Head Number LBA27-24 Command C0hErase Sectors C0h Request Sense 03h Extended Error CodesExtended Error Codes Description Request Sense 03hTranslate Sector 87h Drive Head Number LBA27-24 Command 87hTranslate Sector 87h Wear-Level F5h Wear-Level F5hWrite Multiple w/o Erase CDh Drive Head Number LBA27-24 Command CDhWrite Multiple w/o Erase CDh Write Sectors w/o Erase 38h Drive Head Number LBA27-24 Command 38hWrite Sectors w/o Erase 38h Write Verify 3Ch Drive Head Number LBA27-24 Command 3ChWrite Verify 3Ch SSD YYY Sales and SupportPart Numbering Part Numbering NomenclaturePart Number Capacity Part NumbersRelated Documentation Related Documentation