Silicon Image SSDS00-3650H-R manual Idle 97h, E3h

Page 47

ATA COMMAND BLOCK AND SET DESCRIPTION

SSD-HXXX(I)-3650 DATA SHEET

Idle — 97h, E3h

When issued by the host, the device’s internal controller sets the BSY bit, enters the Idle mode, clears the BSY bit, and generates an interrupt. If the sector count is non-zero, it is interpreted as a timer count with each count being 5ms, and the automatic power-down mode is enabled. If the sector count is zero, the automatic power-down mode is disabled.

Table 36: Idle — 97h, E3h

Register	D7	D6	D5	D4		D3	D2	D1	D0
Feature					X

Sector Count			Timer Count (5ms increments)

Sector Number					X

Cylinder Low					X

Cylinder High					X

Drive Head	X	X	X	Drive			X

Command				97h or E3h

SILICONSYSTEMS PROPRIETARY

This document and the information contained within it is confidential and proprietary to SiliconSystems, Inc.

All unauthorized use and/or reproduction is prohibited.

DOCUMENT: 3650H-02DSR

JUNE 17, 2008

PAGE 35

Image 47

Contents Host and/or software IP FeaturesOverview SisecureDocument No Release Date Changes UpdatedRevision History Table of Contents SSD-HXXXI-3650 Data Sheet Related Documentation Sales and Support Part NumberingSSD-HXXXI-3650 Data Sheet List of Figures List of Figures List of Tables ATA Command Block and Set Description Write Long Sectors 32h, 33h SSD-HXXXI-3650 Data Sheet Physical Dimensions Physical SpecificationsPin Locations System Reliability Product SpecificationsSystem Power Requirements System Performance098,446,336 098,528 4066 Product Capacity SpecificationsEnvironmental Specifications 047,674,880 046,240 2030Pin Electrical SpecificationPin Assignments Disk Active/Slave Present. This open Signal DescriptionsSignal Name Pins Type Description Data Inputs/Outputs. This is the 8-bit orInterrupt Request. This signal is an active DMA Request. This signal is used for DMAController by -IORD and -IOWR. This signal Ground. The device ground signalCapacitance Absolute Maximum RatingsSymbol Parameter 5V ±10% Units Minimum Maximum DC CharacteristicsO Access Read Timing Access Read TimingO Access Write Timing Access Write TimingTrue IDE Read/Write Access Timing True IDE Read/Write Access TimingTrue IDE Multiword DMA Read/Write Access Timing True IDE Multiword DMA Read/Write Access TimingCS0# CS1# DA02 DA01 DA00 Task File Register SpecificationATA and True IDE Register Decoding ATA Registers Error RegisterOperation Feature RegisterRead/Write Feature Byte Sector Count Register Read/Write Sector Count Default ValueLogical Block Number bits A07-A00 LBA Addressing Sector Number RegisterRead/Write Logical Block Number bits A15-A08 LBA Addressing Cylinder Low RegisterLow Logical Block Number bits A23-A16 LBA Addressing Cylinder High RegisterLBA27 LBA26 LBA25 LBA24 Drive/Head RegisterCorrected Data CORR. Always set to Drive Write Fault DWF. Always set toStatus Register Operation Read/Write ATA Command Code Command RegisterAlternate Status Register NIEN Bits Description Device Control RegisterOperation Write Device Address Register Read/Write NWTG NHS3 NHS2 NHS1 NHS0 NDS1 NDS0 Default ValueClass Command Name Registers Used Code ATA Command Block and SET DescriptionATA Command Block and Set Description ATA Command SetATA Command Set Register Check Power Mode 98h, E5hCheck Power Mode 98h, E5h Executive Drive Diagnostic 90h Executive Drive Diagnostic 90hFormat Track 50h Drive Head Number LBA27-24 Command 50hFormat Track 50h Identify Drive ECh Identify Drive EChIdentify Drive Drive Attribute Data Word Data Default Bytes Data Description AddressIdentify Drive Drive Attribute Data Idle 97h, E3h Idle 97h, E3hIdle Immediate 95h, E1h Idle Immediate 95h, E1hInitialize Drive Parameters 91h Initialize Drive Parameters 91hRecalibrate 1Xh Drive Command 1XhRecalibrate 1Xh Read Buffer E4h Read Buffer E4hRead DMA C8h Drive Head Number LBA27-24 Command C8hRead DMA C8h Read Multiple C4h Drive Head Number LBA27-24 Command C4hRead Multiple C4h Read Sector 20h, 21h Drive Head Number LBA27-24 Command 20h or 21hRead Sector 20h, 21h Read Long Sectors 22h, 23h Drive Head Number LBA27-24 Command 22h or 23hRead Long Sectors 22h, 23h Read Verify Sectors 40h, 41h Drive Head Number LBA27-24 Command 40h or 41hRead Verify Sectors 40h, 41h Seek 7Xh Drive Head Number LBA27-24 Command 7XhSeek 7Xh Feature Operation Set Features EFhSet Features EFh Set Features’ AttributesSet Multiple Mode C6h Set Multiple Mode C6hSet Sleep Mode 99h, E6h Set Sleep Mode 99h, E6hStandby 96h, E2h Standby 96h, E2hStandby Immediate 94h, E0h Standby Immediate 94h, E0hWrite Buffer E8h Write Buffer E8hWrite DMA CAh Drive Head NumberLBA27-24 Command CAhWrite DMA CAh Write Multiple C5h Drive Head NumberLBA27-24 Command C5hWrite Multiple C5h Write Sectors 30h, 31h Drive Head Number LBA27-24 Command 30h or 31hWrite Sectors 30h, 31h Write Long Sectors 32h, 33h Drive Head Number LBA27-24 Command 32h or 33hWrite Long Sectors 32h, 33h Erase Sectors C0h Drive Head Number LBA27-24 Command C0hErase Sectors C0h Request Sense 03h Extended Error CodesExtended Error Codes Description Request Sense 03hTranslate Sector 87h Drive Head Number LBA27-24 Command 87hTranslate Sector 87h Wear-Level F5h Wear-Level F5hWrite Multiple w/o Erase CDh Drive Head Number LBA27-24 Command CDhWrite Multiple w/o Erase CDh Write Sectors w/o Erase 38h Drive Head Number LBA27-24 Command 38hWrite Sectors w/o Erase 38h Write Verify 3Ch Drive Head Number LBA27-24 Command 3ChWrite Verify 3Ch 3650 Sales and SupportPart Numbering Part Numbering NomenclaturePart Number Capacity Part NumbersRelated Documentation Related DocumentationStandard Back Label with Lot Front Label Code InformationClick here